[Sample^Water Sample]
Place cup in the water sampling pocket. Press and hold the "Water Sample" button. = 07 water_sampling_v2.png

[Sample^Water Sample Result]
Test the water sample per your clinic's instructions and enter the result. = 29 water test_v2.png

[Sample^Water Sample Result Failed]
Water sample result failed. = 30 water test failed_v2.png

[Consumables^Consumables Installation]
Remove the concentrate and dialysate caps. = 09 remove right cap_v2.png
Connect the acid concentrate to the acid port. = 12 install acid line_v2.png
Connect the bicarbonate concentrate to the bicarbonate port. = 14 install bicarb line_v2.png

[Disposables^Cartridge Installation]
Open the front panel door. = 01 door open_v2.png
Unlock the pump track by moving the lever to its upward position. = 06 pump track open_v2.png
Install the cartridge using the alignment pins.\nInsert tubing into blood and dialsyate pumps = 03 insert cassette_v2.png
Lock the pump track by moving the lever to its downward position. = 05 pump track lock_v2.png

[Disposables^Cartridge Connection]
Connect the cartridge blood lines to the dialyzer. = 18 filter connections_v2.png
Connect the cartridge  dialysis fluid lines to the dialyzer. = 18 filter connections_v2.png
Insert dialyzer into the clamps. = 17 load filter unit_v2.png
Connect the cartridge tubing line to the air vent port. = 19 PBo connection_v2.png
Connect the cartridge dialysis fluid lines to the DG fluid ports. = 15 install dialysate to DG_v2.png

[Disposables^Heparin Syringe]
Fill a syringe with heparin and connect the cartridge heparin tubing line. \nInsert syringe into infusion pump housing. = 21 load syringe_v2.png

[Disposables^Saline Bag]
Hang the saline bag on the left side hook. Spike a saline bag and connect it to the cartridge saline line. = 23 saline connect_v2.png
Close the front panel door. = 02 door closed_v2.png

[Connection^Patient Connection]
Wash your hands and establish vascular access per your clinic's instructions. = 31 wash hand_v2.png
Pinch arterial clamp and venous clamp on located on the cartridge patient lines. = 16 pinch tubing_v2.png
Remove arterial and venous line connector. = 25 remove stunt_v2.png
Connect arterial and venous cartridge lines to your patient access lines. = 24 connect fistula_v2.png

[Connection^Start Treatment]
Unpinch arterial clamp and venous clamp located on the cartridge patient lines. = 16 pinch tubing_v2.png


[^Rinseback Setup]
Pinch arterial line and saline bag line. = 27 clamp arterial and saline_v2.png
Connect arterial line to the saline bag. = 26 connect arterial line_v2.png
Unpinch clamps at the arterial line, saline bag line, and Y-connector. = 28 unclamp arterial and saline_v2.png

 
[^Rinseback Complete]
Pinch arterial and venous line after rinseback is complete. = 27 clamp arterial and saline_v2.png

[Disconnection^Patient Disconnection]
Pinch arterial clamp and venous clamp on located on the cartridge patient lines and access lines. = 16 pinch tubing_v2.png
Disconnect arterial and venous cartridge lines from your patient access lines. = 24 connect fistula_v2.png

[Disposables^Disposables Removal]
Disconnect the cartridge tubing line connected to the air vent port. = 20 PBo connection remove_v2.png
Remove heparin syringe from the infusion pump housing. = 22 remove syringe_v2.png
Disconnect acid and bicarbonate concentrates. Install concentrate fluid cap. = 11 install right cap_v2.png
Disconnect cartridge dialysate lines and connect ends together.\nInstall top dialysis fluid cap. = 10 install left cap_v2.png
Unlock the pump track by moving the lever to its upward position. = 06 pump track open_v2.png
Remove cartridge and dialyzer from the HD device. = 04 remove cassette_v2.png


[^Recirculate]
Recirculate 0 =logo.png
Recirculate 1 =logo.png
Recirculate 2 =logo.png

[Disinfection^Disinfection]
Disinfection1=logo.png
Disinfection2=logo.png
Disinfection3=logo.png

[Chemical Disinfect^Chemical Disinfect]
Disinfection1=logo.png