SystemComm.c

Clone Tools
  • last updated a few seconds ago
Constraints
Constraints: committers
 
Constraints: files
Constraints: dates
DEN-11750 addressed the bugs that Code Clinic reported

  1. … 6 more files in changeset.
Merge branch 'DEN-11750-dg_dev-dg-dialysate-temperature-control-tune-up' of ssh://dvm-linux02:7999/dg/dgfirmware into DEN-11750-dg_dev-dg-dialysate-temperature-control-tune-up

  1. … 1 more file in changeset.
DEN-11750: Renamed msg ack ID for consistency with HD code.

  1. … 2 more files in changeset.
DEN-11750 updated the drivers with the new calibration data

  1. … 8 more files in changeset.
DEN-11750 added fans duty cycles override

  1. … 6 more files in changeset.
DEN-11750 updated the NV data and the drivers

  1. … 11 more files in changeset.
Bamboo Commit: Updated the Copyright section and replaced tabs with 4 spaces

  1. … 94 more files in changeset.
DEN-11114, DEN-11553 resovled fans RPM alarm that was not raised properly

  1. … 1 more file in changeset.
DEN-11114, DEN-11542, DEN-11553 updated the fans RPM alarm start time offset

  1. … 5 more files in changeset.
DEN-11114: Addressed DENDRAI-33 to remove debug UART support.

  1. … 7 more files in changeset.
DEN-11114 updated DG to send the concentrate mixing information to HD per request and receive the target fill flow rate

  1. … 8 more files in changeset.
Bamboo Commit: Updated the Copyright section and replaced tabs with 4 spaces

  1. … 25 more files in changeset.
DEN-9906: Fixed merge conflicts from staging.

  1. … 23 more files in changeset.
DEN-9906: Added publication of DG alarm info (safety line status) and override of its broadcast interval.

  1. … 5 more files in changeset.
Bamboo Commit: Updated the Copyright section and replaced tabs with 4 spaces

  1. … 92 more files in changeset.
DEN-9906: DIAL-138 - Added DG alarm condition status and Dialin cmd to clear all DG alarms.

  1. … 4 more files in changeset.
DEN-9906 updated the dialysate flow sensor driver with the calibration data

  1. … 2 more files in changeset.
DEN-9480 addressed the code review comments

  1. … 30 more files in changeset.
DEN-9480, DEN-10788 continued working on the heaters control and added code to be able override the drain pump RPM once the pump is in the open loop mode

  1. … 17 more files in changeset.
DEN-9480 added stop drain mode command and stop RTC clock command

  1. … 3 more files in changeset.
DEN-9906: changed no ack timeout to 150ms.

DEN-9480, DEN-10409 addressed the DG fault and removed the extra flow sensor check'

  1. … 7 more files in changeset.
DEN-9966: Resolved peer code review comments and added functions to handle sensor override reset

  1. … 8 more files in changeset.
DEN-9906: Use trimmer heater stop command enum for response.

  1. … 2 more files in changeset.
DEN-9480 modified code to test flow. DEN-10521 removed autocal code from the override function

  1. … 5 more files in changeset.
DEN-9906: Fixed merge conflict with message ID name change in common.

  1. … 1 more file in changeset.
DEN-10412 updated the concentrate pumps to convert the values to negative once the direction of the pumps i negative

  1. … 5 more files in changeset.
DEN-9480, DEN-10419, DEN-10420 addressed the bugs in the mentioned bugs

  1. … 6 more files in changeset.
DEN-9906: Added support for new Dialin command to block transmission of specific message(s).

  1. … 2 more files in changeset.
DEN-9480 merged staging

  1. … 20 more files in changeset.