Index: firmware/App/Modes/ModeChemicalDisinfect.c
===================================================================
diff -u -r94a190522ce398399c7b93c59f788d7666ec0060 -r353d01d31bc69d4d1901ff09097ee610bb1c9dbc
--- firmware/App/Modes/ModeChemicalDisinfect.c	(.../ModeChemicalDisinfect.c)	(revision 94a190522ce398399c7b93c59f788d7666ec0060)
+++ firmware/App/Modes/ModeChemicalDisinfect.c	(.../ModeChemicalDisinfect.c)	(revision 353d01d31bc69d4d1901ff09097ee610bb1c9dbc)
@@ -501,7 +501,7 @@
             // TODO turn on the concentrate pumps
 
             // Set the RO pump to run at full pressure
-            setROPumpTargetFlowRate( RO_PUMP_TARGET_FLUSH_FILL_FLOW_RATE_LPM, MAX_RO_PUMP_FLUSH_FILL_PRESSURE_PSI );
+            setROPumpTargetFlowRateLPM( RO_PUMP_TARGET_FLUSH_FILL_FLOW_RATE_LPM, MAX_RO_PUMP_FLUSH_FILL_PRESSURE_PSI );
 
             // Done with final draining
             isThisLastDrain = FALSE;
@@ -610,7 +610,7 @@
              ( getConductivityValue( CONDUCTIVITYSENSORS_CPI_SENSOR )  <=  MAX_INLET_CONDUCTIVITY_US_PER_CM ) )
         {
             setValveState( VPD, VALVE_STATE_OPEN_C_TO_NC );
-            setROPumpTargetFlowRate( RO_PUMP_TARGET_FLUSH_FILL_FLOW_RATE_LPM, MAX_RO_PUMP_FLUSH_FILL_PRESSURE_PSI );
+            setROPumpTargetFlowRateLPM( RO_PUMP_TARGET_FLUSH_FILL_FLOW_RATE_LPM, MAX_RO_PUMP_FLUSH_FILL_PRESSURE_PSI );
             stateTimer = getMSTimerCount();
             stateTrialCounter = 0;
             state = DG_CHEM_DISINFECT_STATE_FLUSH_CIRCULATION;
@@ -1004,7 +1004,7 @@
             setValveState( VRF, VALVE_STATE_R1_C_TO_NC );
 
             // Turn on the RO pump
-            setROPumpTargetFlowRate( RO_PUMP_TARGET_FLUSH_FILL_FLOW_RATE_LPM, MAX_RO_PUMP_FLUSH_FILL_PRESSURE_PSI );
+            setROPumpTargetFlowRateLPM( RO_PUMP_TARGET_FLUSH_FILL_FLOW_RATE_LPM, MAX_RO_PUMP_FLUSH_FILL_PRESSURE_PSI );
 
             // Start heating the water while we are filling up the reservoirs
             setHeaterTargetTemperature( DG_PRIMARY_HEATER, CHEM_DISINFECT_TARGET_TEMPERATURE_C );
@@ -1087,7 +1087,7 @@
             // Set the drain pump to control mode
             setDrainPumpTargetOutletPressure( CHEM_DISINFECT_TARGET_DRAIN_PRES_PSI );
 
-            setROPumpTargetFlowRate( CHEM_DISINFECT_TARGET_RO_FLOW_LPM, CHEM_DISINFECT_MAX_RO_PRESSURE_PSI );
+            setROPumpTargetFlowRateLPM( CHEM_DISINFECT_TARGET_RO_FLOW_LPM, CHEM_DISINFECT_MAX_RO_PRESSURE_PSI );
 
             // Get the current volumes of R1 & R2. These values will be used to make sure the reservoirs'
             // volume does not change more than a certain amount during the actual chemical disinfect cycle
@@ -1389,7 +1389,7 @@
         setValveState( VRF, VALVE_STATE_R1_C_TO_NC );
         setValveState( VRO, VALVE_STATE_R1_C_TO_NO );
         setValveState( VRI, VALVE_STATE_R2_C_TO_NC );
-        setROPumpTargetFlowRate( RO_PUMP_TARGET_FLUSH_FILL_FLOW_RATE_LPM, MAX_RO_PUMP_FLUSH_FILL_PRESSURE_PSI );
+        setROPumpTargetFlowRateLPM( RO_PUMP_TARGET_FLUSH_FILL_FLOW_RATE_LPM, MAX_RO_PUMP_FLUSH_FILL_PRESSURE_PSI );
 
         rsrvr1Status = DG_RESERVOIR_BELOW_TARGET;
         rsrvr2Status = DG_RESERVOIR_BELOW_TARGET;