Index: firmware/App/HDCommon.h
===================================================================
diff -u -r1467e388082a0d4c9e4b7e03b689a70ba42862db -r1af686275f4fd6a11bb3507f9f128eef9636edae
--- firmware/App/HDCommon.h	(.../HDCommon.h)	(revision 1467e388082a0d4c9e4b7e03b689a70ba42862db)
+++ firmware/App/HDCommon.h	(.../HDCommon.h)	(revision 1af686275f4fd6a11bb3507f9f128eef9636edae)
@@ -43,7 +43,7 @@
     #define DISABLE_AIR_TRAP_LEVELING       1           // Disable air trap level control
 //    #define DISABLE_3WAY_VALVES             1           // Disable 3-way valves
 //    #define TST_3WAY_VALVES_ALWAYS_OPEN     1           // After POST and homing, open all 4 valves
-    #define DISABLE_ACCELS                  1           // Disable accelerometer POST and monitoring
+//    #define DISABLE_ACCELS                  1           // Disable accelerometer POST and monitoring
 //    #define DISABLE_CRC_ERROR               1           // Do not error on bad CRC for CAN messages
 //    #define DISABLE_ACK_ERRORS              1           // Do not error on failure of other node(s) to ACK a message
     #define DISABLE_MOTOR_CURRENT_CHECKS    1           // Do not error on HD pump current checks
@@ -54,27 +54,27 @@
     #define ALWAYS_ALLOW_SYRINGE_PUMP_CMDS  1           // Allow syringe pump commands at any time except when pump is busy
     #define DISABLE_PRESSURE_CHECKS         1           // Do not error on HD pressure checks
 //    #define DISABLE_UF_ALARMS               1           // Do not error on HD ultrafiltration checks
-//    #define DISABLE_VALVE_ALARMS            1           // Do not error on HD valve position
+    #define DISABLE_VALVE_ALARMS            1           // Do not error on HD valve position
     #define DISABLE_CAL_CHECK               1           // Disable calibration checks
 //    #define RUN_PUMPS_OPEN_LOOP             1           // BP and DPi pumps will be run open loop (no flow sensor feedback)
 //    #define RAW_FLOW_SENSOR_DATA            1           // Test build will not filter flow sensor data
 //    #define READ_FPGA_ASYNC_DATA            1           // Test build reads non-priority register page every other time
 //    #define EMC_TEST_BUILD                  1           // EMC test build - HD/DG run separately but connected, HD pumps toggle on/off w/ stop button
     #define ALARMS_DEBUG                    1           // Triggered alarms sent to debug UART
     #define ALARM_VOLUME_DEFAULT_LOW        1           // Set default alarm volume to lowest
-    #define TEMP_UI_ALARM_SILENCE_FIX       1           // Temporary UI fix for handling alarm silence request msg
+//    #define TEMP_UI_ALARM_SILENCE_FIX       1           // Temporary UI fix for handling alarm silence request msg
     #define SKIP_PRIMING                    1           // Skip Pre-treatment Prime
     #define SKIP_WET_SELF_TESTS             1           // Skip Pre-treatment prime wet self-tests
 //    #define V1_5_SYSTEM                     1           // Build for v1.5 system
 //    #define V2_0_SYSTEM                     1           // Build for v2.0 system
-    #define SKIP_SAMPLE_WATER               1           // Skip pre-treatment sample water
+//    #define SKIP_SAMPLE_WATER               1           // Skip pre-treatment sample water
     #define SKIP_CONSUMABLE_TESTS           1           // Skip pre-treatment consumable Self-tests
     #define SKIP_DRY_SELF_TESTS             1           // Skip pre-treatment dry self-tests
-    #define SKIP_UI_INTERACTION             1           // Skip UI interaction.
+//    #define SKIP_UI_INTERACTION             1           // Skip UI interaction.
 //    #define DISABLE_BATT_COMM               1           // Disable battery communication.
     #define SKIP_AIR_BUBBLE_CHECK           1           // Skip air bubble detector self-test.
     #define DISABLE_OCCLUSION_SELF_TEST     1           // Skip occlusion sensor self-test.
-    #define SKIP_CARTRIDGE_REMOVAL          1           // Skip cartridge removal check
+//    #define SKIP_CARTRIDGE_REMOVAL          1           // Skip cartridge removal check
     #define SKIP_EMPTY_RES_CHECK            1           // Skip reservoir empty check
     #define DISABLE_FPGA_COUNTER_CHECKS     1           // Disable alarms associated with FPGA read/error counters