Index: firmware/App/HDCommon.h =================================================================== diff -u -r570032a2681a0ac93f7306130c9e8232f6fd9cd9 -r15f9827c863812cfd1f891d22342103fe9a72abc --- firmware/App/HDCommon.h (.../HDCommon.h) (revision 570032a2681a0ac93f7306130c9e8232f6fd9cd9) +++ firmware/App/HDCommon.h (.../HDCommon.h) (revision 15f9827c863812cfd1f891d22342103fe9a72abc) @@ -38,29 +38,15 @@ // #define SIMULATE_UI 1 // Build w/o requirement that UI be there // #define TASK_TIMING_OUTPUT_ENABLED 1 // Re-purposes alarm lamp pins for task timing // TODO convert the new configuration way - #define DISABLE_ALARM_AUDIO 1 // Disable alarm audio -// #define SKIP_POST 1 // Skip POST tests - all pass -// #define DONT_SKIP_NV_POST 1 // Do not skip NV Data POST - #define DISABLE_AIR_TRAP_LEVELING_ALARM 1 // Disable air trap level control alarms // #define DISABLE_3WAY_VALVES 1 // Disable 3-way valves // #define TST_3WAY_VALVES_ALWAYS_OPEN 1 // After POST and homing, open all 4 valves // #define DISABLE_ACCELS 1 // Disable accelerometer POST and monitoring // #define DISABLE_CRC_ERROR 1 // Do not error on bad CRC for CAN messages - #define DISABLE_ACK_ERRORS 1 // Do not error on failure of other node(s) to ACK a message +// #define DISABLE_ACK_ERRORS 1 // Do not error on failure of other node(s) to ACK a message // TODO sw config implemented // #define RUN_BP_OPEN_LOOP 1 // Run blood pump in open loop mode // #define RUN_DPI_OPEN_LOOP 1 // Run dialysate inlet pump in open loop mode - #define WORN_OUT_CARTRIDGE 1 // Running with an old worn out cartridge (max wear) // #define PBA_ESTIMATION 1 // Estimate arterial pressure rather than look at PBA sensor -// #define DISABLE_MOTOR_CURRENT_CHECKS 1 // Do not error on HD pump current checks -// #define DISABLE_PUMP_FLOW_CHECKS 1 // Do not error on HD pump flow checks -// #define DISABLE_PUMP_SPEED_CHECKS 1 // Do not error on HD pump speed checks -// #define DISABLE_PUMP_DIRECTION_CHECKS 1 // Do not error on HD pump direction checks - #define DISABLE_SYRINGE_PUMP 1 // Disable syringe pump functionality - #define ALWAYS_ALLOW_SYRINGE_PUMP_CMDS 1 // Allow syringe pump commands at any time except when pump is busy - #define DISABLE_PRESSURE_CHECKS 1 // Do not error on HD pressure checks - #define DISABLE_ARTERIAL_PRESSURE_CHECK 1 // Do not error on arterial pressure out of range - #define DISABLE_VENOUS_PRESSURE_CHECK 1 // Do not error on venous pressure out of range -// #define USE_PBO_AS_PBA 1 // PBo readings used for PBA, PBo replaced with fixed pressure (100 mmHg) + #define USE_PBO_AS_PBA 1 // PBo readings used for PBA, PBo replaced with fixed pressure (100 mmHg) // #define DISABLE_UF_ALARMS 1 // Do not error on HD ultrafiltration checks #define DISABLE_DIALYSATE_TEMP_CHECK 1 // Disable dialysate temperature check @@ -78,26 +64,14 @@ // #define DISABLE_FPGA_COUNTER_CHECKS 1 // Disable alarms associated with FPGA read/error counters #define DISABLE_VOLTAGE_MONITOR 1 // Disable voltage monitoring/alarms #define ALLOW_1_MIN_TREATMENT_DURATION 1 // Allow user to change treatment duration to as low as 1 minute -// #define DISABLE_SYRINGE_PUMP_ALARMS 1 // Disable some syringe pump alarms that are triggering intermittently - #define NO_PUMP_FLOW_LIMITS 1 // Allow any commanded flow rate for peristaltic pumps +// #define NO_PUMP_FLOW_LIMITS 1 // Allow any commanded flow rate for peristaltic pumps #define DISABLE_BUBBLE_ALARMS 1 // Disable bubble alarms #define DISABLE_UI_POST_TEST 1 // Disable the UI POST // #define DISABLE_UI_COMM_TO_ALARM 1 // Disable UI comm timeouts #define DISABLE_WD_AND_SFTY_POST_TESTS 1 // Disable watchdog and safety shutdown POST tests #define DISABLE_ILLEGAL_AIR_TRAP_ALARM 1 // Disable illegal state for air trap alarm #define SKIP_RESERVOIR_ALARMS 1 // Skip reservoir management alarms - // #define IGNORE_BLOOD_LEAK_SELF_TEST 1 // Ignore blood leak self test // TODO New config implemented -// #define IGNORE_BLOOD_LEAK_ALARM 1 // Ignore blood leak alarm // TODO New config implemented -// #define DISABLE_SERVICE_RECORD 1 - // Skip Pre-Treatment and get to treatment as soon as possible - #define SKIP_UI_INTERACTION 1 // Skip UI interaction. // TODO New config implemented - #define SKIP_SAMPLE_WATER 1 // Skip pre-treatment sample water // TODO New config implemented - #define SKIP_CONSUMABLE_TESTS 1 // Skip pre-treatment consumable Self-tests // TODO New config implemented - #define SKIP_DRY_SELF_TESTS 1 // Skip pre-treatment dry self-tests - #define SKIP_PRIMING 1 // Skip Pre-treatment Prime - #define SKIP_WET_SELF_TESTS 1 // Skip Pre-treatment prime wet self-tests - #include #include #endif