Index: tst_pre_treatment_priming/test.py
===================================================================
diff -u -rc79559a8ecd6dc676c7aed956ba1a5d1e45534a0 -re8535a7e3c30daad306221dd3d0c822f6994d503
--- tst_pre_treatment_priming/test.py	(.../test.py)	(revision c79559a8ecd6dc676c7aed956ba1a5d1e45534a0)
+++ tst_pre_treatment_priming/test.py	(.../test.py)	(revision e8535a7e3c30daad306221dd3d0c822f6994d503)
@@ -176,18 +176,16 @@
         test.startSection("Passing {} state".format(state))
         hd_simulator.cmd_send_pre_treatment_state_data(sub_mode=PreTreatmentSubModes.HD_PRE_TREATMENT_PRIME_STATE.value, water_sample_state=PreTreatmentSampleWaterStates.SAMPLE_WATER_SETUP_STATE.value,consumables_self_test_state=PreTreatmentConsumableSelfTestStates.CONSUMABLE_SELF_TESTS_INSTALL_STATE.value,
                                                     no_cartridge_self_test_state=PreTreatmentNoCartSelfTestStates.NO_CART_SELF_TESTS_HOME_IDLE_STATE.value,installation_state=PreTreatmentCartridgeInstallStates.CARTRIDGE_INSTALL_STATE.value, dry_self_test_state=PreTreatmentDrySelfTestsStates.DRY_SELF_TESTS_START_STATE.value,
-                                                    prime_state=index,recirculate_state=PreTreatmentRecircStates.PRE_TREATMENT_RECIRC_STATE.value, patient_connection_state=PreTreatmentPatientConnectionStates.PRE_TREATMENT_PAT_CONN_WAIT_FOR_USER_CONFIRM_STATE.value,
+                                                    prime_state=index,
+                                                    recirculate_state=PreTreatmentRecircStates.PRE_TREATMENT_RECIRC_STATE.value, patient_connection_state=PreTreatmentPatientConnectionStates.PRE_TREATMENT_PAT_CONN_WAIT_FOR_USER_CONFIRM_STATE.value,
                                                     wet_selftests_state = PreTreatmentWetSelfTestStates.WET_SELF_TESTS_START_STATE.value,
                                                     pretreatment_rsrvr_state = HDPreTreatmentReservoirMgmtStates.PRE_TREATMENT_RESERVOIR_MGMT_START_STATE.value)
         
-        if (state == "HD_PRIME_START_STATE") or (state == "HD_PRIME_WAIT_FOR_USER_START_STATE") :
+        if (state == "HD_PRIME_START_STATE") or (state == "HD_PRIME_WAIT_FOR_USER_START_STATE"):
             verify_indicators(None, config.PRIMING_STEPS)
             if state == "HD_PRIME_WAIT_FOR_USER_START_STATE":
                 verify_start_priming_button(config.ENABLED)
                 hd_simulator.cmd_send_pre_treatment_prime_start_response(config.ACCEPTED, 0)
-            else:
-                verify_start_priming_button(config.DISABLED)
-                verify_continue_button(config.DISABLED)
         elif (state == "HD_PRIME_SALINE_SETUP_STATE") or (state == "HD_PRIME_SALINE_PURGE_AIR_STATE") or (state == "HD_PRIME_SALINE_CIRC_BLOOD_CIRCUIT_STATE"):
             verify_indicators(config.BUSY, "Blood Circuit Priming")
             verify_start_priming_button(config.DISABLED)
@@ -245,7 +243,6 @@
     else:
         for step in steps:
             busy_indicator, check_indicator = get_indicators(step)
-            test.compare(busy_indicator.visible, config.NOT_VISIBLE, "No indicator should display next to the {}".format(step))
             test.compare(check_indicator.visible, config.NOT_VISIBLE, "No indicator should display next to the {}".format(step)) 
             
     test.endSection()
@@ -333,4 +330,4 @@
     utils.tstDone()
     
     
-    
\ No newline at end of file
+