[0]
Title     = 
ListTitle = 
Message   = 

[1]
Title     = Stuck Button
ListTitle = HD POST: Stuck Button
Message   = A button was pressed during start up and appears stuck. \n- Press and release the power and stop buttons on the\nfront of the device.\n- Turn device off, then back on.\n- If problem continues, call service to schedule a repair.

[2]
Title     = Service Required: Hemodialysis Device
ListTitle = HD POST: FPGA Compatibility
Message   = A problem was detected with the hemodialysis device.\n- Locate the ID code found in the bottom left corner\nof the alarm screen.\n- Call service to report the issue and schedule a repair.

[3]
Title     = Service Required: Dialysate Device
ListTitle = DG POST: FPGA Compatibility
Message   = A problem was detected with the dialysate device.\n- Locate the ID code found in the bottom left corner\nof the alarm screen.\n- Call service to report the issue and schedule a repair.
SRSDG 602
SRSDG 814
SRSDG 1061 = 

[4]
Title     = Service Required: Hemodialysis Device
ListTitle = HD POST: WD Safestate
Message   = A problem was detected with the hemodialysis device.\n- Locate the ID code found in the bottom left corner\nof the alarm screen.\n- Call service to report the issue and schedule a repair.

[5]
Title     = Service Required: Dialysate Device
ListTitle = DG POST: WD Safestate
Message   = A problem was detected with the dialysate device.\n- Locate the ID code found in the bottom left corner\nof the alarm screen.\n- Call service to report the issue and schedule a repair.
SRSDG 53 = 

[6]
Title     = Service Required: Hemodialysis Device
ListTitle = HD POST: Proc- UI Comm
Message   = A problem was detected with the hemodialysis device.\n- Locate the ID code found in the bottom left corner\nof the alarm screen.\n- Call service to report the issue and schedule a repair.

[7]
Title     = Service Required: Hemodialysis Device
ListTitle = HD Alarm (Low): RTC Bat Low
Message   = A non- critical problem was detected with the hemodialysis\n device.\n- Call service to report the issue and schedule a repair.

[8]
Title     = Service Required: Hemodialysis Device
ListTitle = HD POST: Acc Vector
Message   = A problem was detected with the hemodialysis device.\n- Locate the ID code found in the bottom left corner\nof the alarm screen.\n- Call service to report the issue and schedule a repair.

[9]
Title     = Service Required: Dialysate Device
ListTitle = DG POST: Acc Vector
Message   = A problem was detected with the dialysate device.\n- Locate the ID code found in the bottom left corner\nof the alarm screen.\n- Call service to report the issue and schedule a repair.
SRSDG 323 = 

[10]
Title     = Service Required: Hemodialysis Device
ListTitle = HD POST: BLD Config Emb Mode
Message   = A problem was detected with the hemodialysis device.\n- Locate the ID code found in the bottom left corner\nof the alarm screen.\n- Call service to report the issue and schedule a repair.

[11]
Title     = Low Dialysate Temperature
ListTitle = Dial. Gen: Dialysate Temp Low
Message   = Dialysate temperature is low. \n- Treatment is currently paused.\n- When dialysate temperature is within target range,\n treatment will need to be resumed.

[12]
Title     = Service Required: Hemodialysis Device
ListTitle = HD POST: HD Image
Message   = A problem was detected with the hemodialysis device.\n- Locate the ID code found in the bottom left corner\nof the alarm screen.\n- Call service to report the issue and schedule a repair.

[13]
Title     = Service Required: Dialysate Device
ListTitle = DG POST: DG Image
Message   = A problem was detected with the dialysate device.\n- Locate the ID code found in the bottom left corner\nof the alarm screen.\n- Call service to report the issue and schedule a repair.
SRSDG 813 = 

[14]
Title     = Service Required: Dialysate Device
ListTitle = DG POST: Usage Rec NVRAM CRC
Message   = A problem was detected with the dialysate device.\n- Locate the ID code found in the bottom left corner\nof the alarm screen.\n- Call service to report the issue and schedule a repair.
SRSDG 957 = 

[15]
Title     = High Dialysate Temperature
ListTitle = Dial. Gen: Dialysate Temp High
Message   = Dialysate temperature is high. \n- Treatment is currently paused.\n- When dialysate temperature is within target range,\n treatment will need to be resumed.

[16]
Title     = Service Required: Hemodialysis Device
ListTitle = HD POST: Primary Alarm Current
Message   = A problem was detected with the hemodialysis device.\n- Locate the ID code found in the bottom left corner\nof the alarm screen.\n- Call service to report the issue and schedule a repair.

[17]
Title     = Service Required: Hemodialysis Device
ListTitle = HD POST: UI POST Not Complete
Message   = A problem was detected with the hemodialysis device.\n- Locate the ID code found in the bottom left corner\nof the alarm screen.\n- Call service to report the issue and schedule a repair.

[18]
Title     = Communication Error
ListTitle = Loss of DG Comm (DG ACK)
Message   = A communication problem has been detected.\n- Treatment must be terminated.\n- Locate the ID code found in the bottom left corner\nof the alarm screen.\n- Call service to report the issue and schedule a repair.

[19]
Title     = High Dialysate Temperature
ListTitle = Dial. Gen: Dialysate Temp High
Message   = Dialysate temperature is high. \n- Treatment is currently paused.\n- When dialysate temperature is within target range,\n treatment will need to be resumed.

[20]
Title     = Service Required: Dialysate Device
ListTitle = DG POST: Conductivity Cal
Message   = A problem was detected with the dialysate device.\n- Locate the ID code found in the bottom left corner\nof the alarm screen.\n- Call service to report the issue and schedule a repair.
SRSDG 16 = 

[21]
Title     = Service Required: Dialysate Device
ListTitle = DG POST: Drain Line Vol Cal
Message   = A problem was detected with the dialysate device.\n- Locate the ID code found in the bottom left corner\nof the alarm screen.\n- Call service to report the issue and schedule a repair.
SRSDG 936 = 

[22]
Title     = Service Required: Dialysate Device
ListTitle = DG POST: Reservoir Vol Cal
Message   = A problem was detected with the dialysate device.\n- Locate the ID code found in the bottom left corner\nof the alarm screen.\n- Call service to report the issue and schedule a repair.
SRSDG 935 = 

[23]
Title     = Service Required: Dialysate Device
ListTitle = DG POST: Acid Conc Cal
Message   = A problem was detected with the dialysate device.\n- Locate the ID code found in the bottom left corner\nof the alarm screen.\n- Call service to report the issue and schedule a repair.
SRSDG 934 = 

[24]
Title     = Service Required: Dialysate Device
ListTitle = DG POST: Bicarb Conc Cal
Message   = A problem was detected with the dialysate device.\n- Locate the ID code found in the bottom left corner\nof the alarm screen.\n- Call service to report the issue and schedule a repair.
SRSDG 933 = 

[25]
Title     = Service Required: Dialysate Device
ListTitle = DG POST: Acc Cal
Message   = A problem was detected with the dialysate device.\n- Locate the ID code found in the bottom left corner\nof the alarm screen.\n- Call service to report the issue and schedule a repair.
SRSDG 817 = 

[26]
Title     = Service Required: Hemodialysis Device
ListTitle = HD POST: Acc Cal
Message   = A problem was detected with the hemodialysis device.\n- Locate the ID code found in the bottom left corner\nof the alarm screen.\n- Call service to report the issue and schedule a repair.

[27]
Title     = Self Test: Blood Leak
ListTitle = Process: Pre- Tx Wet Self- Test
Message   = A problem has been detected with the blood leak sensor.\n- Confirm cartridge is properly installed.\n- If problem persists, terminate treatment preparation and \n begin again using a new cartridge.

[28]
Title     = Service Required: Dialysate Device
ListTitle = DG Fault: Conductivity RTD Comm
Message   = A problem was detected with the dialysate device. \n- Treatment must be terminated.\n- Locate the ID code found in the bottom left corner\nof the alarm screen.\n- Call service to report the issue and schedule a repair.
SRSDG 864 = 

[29]
Title     = Service Required: Hemodialysis Device
ListTitle = HD POST: SP DAC Cal
Message   = A problem was detected with the hemodialysis device.\n- Locate the ID code found in the bottom left corner\nof the alarm screen.\n- Call service to report the issue and schedule a repair.

[30]
Title     = Service Required: Hemodialysis Device
ListTitle = HD Fault: SW Invalid State
Message   = A problem was detected with the hemodialysis device. \n- Treatment must be terminated.\n- Locate the ID code found in the bottom left corner\nof the alarm screen.\n- Call service to report the issue and schedule a repair.

[31]
Title     = Service Required: Hemodialysis Device
ListTitle = HD Fault: BP Current
Message   = A problem was detected with the hemodialysis device. \n- Treatment must be terminated.\n- Locate the ID code found in the bottom left corner\nof the alarm screen.\n- Call service to report the issue and schedule a repair.

[32]
Title     = Service Required: Hemodialysis Device
ListTitle = HD Fault: BP Speed
Message   = A problem was detected with the hemodialysis device. \n- Treatment must be terminated.\n- Locate the ID code found in the bottom left corner\nof the alarm screen.\n- Call service to report the issue and schedule a repair.

[33]
Title     = Service Required: Hemodialysis Device
ListTitle = HD Fault: BP Direction
Message   = A problem was detected with the hemodialysis device. \n- Treatment must be terminated.\n- Locate the ID code found in the bottom left corner\nof the alarm screen.\n- Call service to report the issue and schedule a repair.

[34]
Title     = Blood Pump Error
ListTitle = HD Fault: BP Rotor
Message   = A problem has been detected with the blood pump.\n- Treatment must be terminated.\n- Locate the ID code found in the bottom left corner\nof the alarm screen.\n- Call service to report the issue.

[35]
Title     = Service Required: Hemodialysis Device
ListTitle = HD Fault: DPi Current
Message   = A problem was detected with the hemodialysis device. \n- Treatment must be terminated.\n- Locate the ID code found in the bottom left corner\nof the alarm screen.\n- Call service to report the issue and schedule a repair.

[36]
Title     = Service Required: Hemodialysis Device
ListTitle = HD Fault: DPi Speed
Message   = A problem was detected with the hemodialysis device. \n- Treatment must be terminated.\n- Locate the ID code found in the bottom left corner\nof the alarm screen.\n- Call service to report the issue and schedule a repair.

[37]
Title     = Service Required: Hemodialysis Device
ListTitle = HD Fault: DPi Direction
Message   = A problem was detected with the hemodialysis device. \n- Treatment must be terminated.\n- Locate the ID code found in the bottom left corner\nof the alarm screen.\n- Call service to report the issue and schedule a repair.

[38]
Title     = Dialysate Pump Error
ListTitle = HD Fault: DPi Rotor
Message   = A problem has been detected with the dialysate pump.\n- Treatment must be terminated.\n- Locate the ID code found in the bottom left corner\nof the alarm screen.\n- Call service to report the issue.

[39]
Title     = Service Required: Hemodialysis Device
ListTitle = HD Fault: DPo Current
Message   = A problem was detected with the hemodialysis device. \n- Treatment must be terminated.\n- Locate the ID code found in the bottom left corner\nof the alarm screen.\n- Call service to report the issue and schedule a repair.

[40]
Title     = Service Required: Hemodialysis Device
ListTitle = HD Fault: DPo Speed
Message   = A problem was detected with the hemodialysis device. \n- Treatment must be terminated.\n- Locate the ID code found in the bottom left corner\nof the alarm screen.\n- Call service to report the issue and schedule a repair.

[41]
Title     = Service Required: Hemodialysis Device
ListTitle = HD Fault: DPo Direction
Message   = A problem was detected with the hemodialysis device. \n- Treatment must be terminated.\n- Locate the ID code found in the bottom left corner\nof the alarm screen.\n- Call service to report the issue and schedule a repair.

[42]
Title     = Dialysate Pump Error
ListTitle = HD Fault: DPo Rotor
Message   = A problem has been detected with the dialysate pump.\n- Treatment must be terminated.\n- Locate the ID code found in the bottom left corner\nof the alarm screen.\n- Call service to report the issue.

[43]
Title     = Service Required: Dialysate Device
ListTitle = DG Fault: Iso ADC Comm
Message   = A problem was detected with the dialysate device. \n- Treatment must be terminated.\n- Locate the ID code found in the bottom left corner\nof the alarm screen.\n- Call service to report the issue and schedule a repair.
SRSDG 954 = 

[44]
Title     = Service Required: Hemodialysis Device
ListTitle = HD Fault: UI Comm
Message   = A problem was detected with the hemodialysis device. \n- Treatment must be terminated.\n- Locate the ID code found in the bottom left corner\nof the alarm screen.\n- Call service to report the issue and schedule a repair.

[45]
Title     = Service Required: Hemodialysis Device
ListTitle = HD Fault: CAN CRC Com
Message   = A problem was detected with the hemodialysis device. \n- Treatment must be terminated.\n- Locate the ID code found in the bottom left corner\nof the alarm screen.\n- Call service to report the issue and schedule a repair.

[46]
Title     = Service Required: Hemodialysis Device
ListTitle = HD Fault: CAN ACK UI Com
Message   = A problem was detected with the hemodialysis device. \n- Treatment must be terminated.\n- Locate the ID code found in the bottom left corner\nof the alarm screen.\n- Call service to report the issue and schedule a repair.

[47]
Title     = Service Required: Dialysate Device
ListTitle = DG Fault: RO Pump High
Message   = A problem was detected with the dialysate device. \n- Treatment must be terminated.\n- Locate the ID code found in the bottom left corner\nof the alarm screen.\n- Call service to report the issue and schedule a repair.

[48]
Title     = Service Required: Hemodialysis Device
ListTitle = HD Fault: UF Rate Tare Err
Message   = A problem was detected with the hemodialysis device. \n- Treatment must be terminated.\n- Locate the ID code found in the bottom left corner\nof the alarm screen.\n- Call service to report the issue and schedule a repair.

[49]
Title     = Service Required: Hemodialysis Device
ListTitle = HD Fault: FPGA Com
Message   = A problem was detected with the hemodialysis device. \n- Treatment must be terminated.\n- Locate the ID code found in the bottom left corner\nof the alarm screen.\n- Call service to report the issue and schedule a repair.

[50]
Title     = Service Required: Dialysate Device
ListTitle = DG Fault: Valve Control
Message   = A problem was detected with the dialysate device. \n- Treatment must be terminated.\n- Locate the ID code found in the bottom left corner\nof the alarm screen.\n- Call service to report the issue and schedule a repair.
SRSDG 26 = 

[51]
Title     = Service Required: Hemodialysis Device
ListTitle = HD Fault: BP Speed
Message   = A problem was detected with the hemodialysis device. \n- Treatment must be terminated.\n- Locate the ID code found in the bottom left corner\nof the alarm screen.\n- Call service to report the issue and schedule a repair.

[52]
Title     = Service Required: Hemodialysis Device
ListTitle = HD Fault: DPi Speed
Message   = A problem was detected with the hemodialysis device. \n- Treatment must be terminated.\n- Locate the ID code found in the bottom left corner\nof the alarm screen.\n- Call service to report the issue and schedule a repair.

[53]
Title     = Service Required: Hemodialysis Device
ListTitle = HD Fault: DPo Speed
Message   = A problem was detected with the hemodialysis device. \n- Treatment must be terminated.\n- Locate the ID code found in the bottom left corner\nof the alarm screen.\n- Call service to report the issue and schedule a repair.

[54]
Title     = Service Required: Hemodialysis Device
ListTitle = HD Fault: Critical Data Err
Message   = A problem was detected with the hemodialysis device. \n- Treatment must be terminated.\n- Locate the ID code found in the bottom left corner\nof the alarm screen.\n- Call service to report the issue and schedule a repair.

[55]
Title     = Service Required: Dialysate Device
ListTitle = DG Fault: Critical Data Err
Message   = A problem was detected with the dialysate device. \n- Treatment must be terminated.\n- Locate the ID code found in the bottom left corner\nof the alarm screen.\n- Call service to report the issue and schedule a repair.
SRSDG 921 = 

[56]
Title     = Service Required: Hemodialysis Device
ListTitle = HD Fault: Acc Com
Message   = A problem was detected with the hemodialysis device. \n- Treatment must be terminated.\n- Locate the ID code found in the bottom left corner\nof the alarm screen.\n- Call service to report the issue and schedule a repair.

[57]
Title     = Service Required: Dialysate Device
ListTitle = DG Fault: Acc Com
Message   = A problem was detected with the dialysate device. \n- Treatment must be terminated.\n- Locate the ID code found in the bottom left corner\nof the alarm screen.\n- Call service to report the issue and schedule a repair.
SRSDG 869
SRSDG 870 = 

[58]
Title     = Service Required: Hemodialysis Device
ListTitle = HD Fault: Valve Home
Message   = A problem was detected with the hemodialysis device. \n- Treatment must be terminated.\n- Locate the ID code found in the bottom left corner\nof the alarm screen.\n- Call service to report the issue and schedule a repair.

[59]
Title     = Service Required: Hemodialysis Device
ListTitle = HD Fault: Valve Transition Err
Message   = A problem was detected with the hemodialysis device. \n- Treatment must be terminated.\n- Locate the ID code found in the bottom left corner\nof the alarm screen.\n- Call service to report the issue and schedule a repair.

[60]
Title     = Service Required: Hemodialysis Device
ListTitle = HD Fault: Valve Control
Message   = A problem was detected with the hemodialysis device. \n- Treatment must be terminated.\n- Locate the ID code found in the bottom left corner\nof the alarm screen.\n- Call service to report the issue and schedule a repair.

[61]
Title     = Service Required: Hemodialysis Device
ListTitle = HD Fault: Valve Current
Message   = A problem was detected with the hemodialysis device. \n- Treatment must be terminated.\n- Locate the ID code found in the bottom left corner\nof the alarm screen.\n- Call service to report the issue and schedule a repair.

[62]
Title     = Service Required: Hemodialysis Device
ListTitle = HD Fault: Valve Position
Message   = A problem was detected with the hemodialysis device. \n- Treatment must be terminated.\n- Locate the ID code found in the bottom left corner\nof the alarm screen.\n- Call service to report the issue and schedule a repair.

[63]
Title     = Service Required: Hemodialysis Device
ListTitle = HD Fault: Pre- Tx Hep. Pump Timeout.
Message   = A problem was detected with the hemodialysis device. \n- Treatment must be terminated.\n- Locate the ID code found in the bottom left corner\nof the alarm screen.\n- Call service to report the issue and schedule a repair.

[64]
Title     = Service Required: Dialysate Device
ListTitle = DG Fault: Baro Range
Message   = A problem was detected with the dialysate device. \n- Treatment must be terminated.\n- Locate the ID code found in the bottom left corner\nof the alarm screen.\n- Call service to report the issue and schedule a repair.
SRSDG 874 = 

[65]
Title     = Communication Error
ListTitle = Loss of DG Comm (Reject)
Message   = A communication problem has been detected.\n- Treatment must be terminated.\n- Locate the ID code found in the bottom left corner\nof the alarm screen.\n- Call service to report the issue and schedule a repair.

[66]
Title     = Service Required: Hemodialysis Device
ListTitle = HD POST: BLD Config Set Point
Message   = A problem was detected with the hemodialysis device.\n- Locate the ID code found in the bottom left corner\nof the alarm screen.\n- Call service to report the issue and schedule a repair.

[67]
Title     = Self Test: Cartridge
ListTitle = Process: Pre- Tx Remove Cartridge
Message   = A cartridge has been detected during self- test.\n- Open door\n- Remove cartridge\n- Close door\n- Press Resume/OK

[68]
Title     = Dialysate Generation Error
ListTitle = Dial. Gen: Dialysate not ready
Message   = A problem has been detected with dialysate generation. \n- Treatment is paused and will need to be resumed when \ndialysate is ready for use.

[69]
Title     = Service Required: Hemodialysis Device
ListTitle = HD POST: BLD Cal
Message   = A problem was detected with the hemodialysis device.\n- Locate the ID code found in the bottom left corner\nof the alarm screen.\n- Call service to report the issue and schedule a repair.

[70]
Title     = Self Test: Cartridge
ListTitle = Process: Pre- Tx Remove Cartridge
Message   = A cartridge has been detected during self- test.\n- Open door\n- Remove cartridge\n- Close door\n- Press Resume/OK

[71]
Title     = Self Test: Cartridge
ListTitle = Process: Pre- Tx Remove Cartridge
Message   = A cartridge was detected during self- test.\n- Open door\n- Remove cartridge\n- Close door\n- Press Resume/OK

[72]
Title     = Communication Error
ListTitle = Loss of DG Comm (LC)
Message   = A communication problem has been detected.\n- Treatment must be terminated.\n- Locate the ID code found in the bottom left corner\nof the alarm screen.\n- Call service to report the issue and schedule a repair.

[73]
Title     = Communication Error
ListTitle = Loss of DG Comm (TDI/TRO)
Message   = A communication problem has been detected.\n- Treatment must be terminated.\n- Locate the ID code found in the bottom left corner\nof the alarm screen.\n- Call service to report the issue and schedule a repair.

[74]
Title     = Service Required: Dialysate Device
ListTitle = DG Fault: UVi On No Flow
Message   = A problem was detected with the dialysate device. \n- Treatment must be terminated.\n- Locate the ID code found in the bottom left corner\nof the alarm screen.\n- Call service to report the issue and schedule a repair.
SRSDG 600 = 

[75]
Title     = Service Required: Hemodialysis Device
ListTitle = HD Fault: Syringe DAC
Message   = A problem was detected with the hemodialysis device. \n- Treatment must be terminated.\n- Locate the ID code found in the bottom left corner\nof the alarm screen.\n- Call service to report the issue and schedule a repair.

[76]
Title     = Service Required: Hemodialysis Device
ListTitle = HD Fault: Voltage Monitor
Message   = A problem was detected with the hemodialysis device. \n- Treatment must be terminated.\n- Locate the ID code found in the bottom left corner\nof the alarm screen.\n- Call service to report the issue and schedule a repair.

[77]
Title     = Service Required: Dialysate Device
ListTitle = DG Fault: Voltage Monitor
Message   = A problem was detected with the dialysate device. \n- Treatment must be terminated.\n- Locate the ID code found in the bottom left corner\nof the alarm screen.\n- Call service to report the issue and schedule a repair.
SRSDG 46
SRSDG 866
SRSDG 1088 = 

[78]
Title     = Service Required: Hemodialysis Device
ListTitle = HD Fault: Syringe Pump Enc Dir
Message   = A problem was detected with the hemodialysis device. \n- Treatment must be terminated.\n- Locate the ID code found in the bottom left corner\nof the alarm screen.\n- Call service to report the issue and schedule a repair.

[79]
Title     = Service Required: Hemodialysis Device
ListTitle = HD Fault: Syringe Pump Drv Dir
Message   = A problem was detected with the hemodialysis device. \n- Treatment must be terminated.\n- Locate the ID code found in the bottom left corner\nof the alarm screen.\n- Call service to report the issue and schedule a repair.

[80]
Title     = Service Required: Hemodialysis Device
ListTitle = HD Fault: Syringe Pump Driver
Message   = A problem was detected with the hemodialysis device. \n- Treatment must be terminated.\n- Locate the ID code found in the bottom left corner\nof the alarm screen.\n- Call service to report the issue and schedule a repair.

[81]
Title     = Service Required: Hemodialysis Device
ListTitle = HD Fault: Syringe Pump OT
Message   = A problem was detected with the hemodialysis device. \n- Treatment must be terminated.\n- Locate the ID code found in the bottom left corner\nof the alarm screen.\n- Call service to report the issue and schedule a repair.

[82]
Title     = Service Required: Hemodialysis Device
ListTitle = HD Fault: Syringe Pump DAC Err
Message   = A problem was detected with the hemodialysis device. \n- Treatment must be terminated.\n- Locate the ID code found in the bottom left corner\nof the alarm screen.\n- Call service to report the issue and schedule a repair.

[83]
Title     = Service Required: Hemodialysis Device
ListTitle = HD Fault: Syringe Pump On Err
Message   = A problem was detected with the hemodialysis device. \n- Treatment must be terminated.\n- Locate the ID code found in the bottom left corner\nof the alarm screen.\n- Call service to report the issue and schedule a repair.

[84]
Title     = Service Required: Dialysate Device
ListTitle = DG POST: DG RTC Time
Message   = A problem was detected with the dialysate device.\n- Locate the ID code found in the bottom left corner\nof the alarm screen.\n- Call service to report the issue and schedule a repair.
SRSDG 815 = 

[85]
Title     = Cartridge Lever is Open
ListTitle = Blood Stop: Cartridge Lever Open
Message   = A problem has been detected with the cartridge.\n- Open the device door and push lever all the way down.\n- Close the device door.\n- Press Resume/OK button to continue.

[86]
Title     = Service Required: Hemodialysis Device
ListTitle = HD POST: HD RTC Time
Message   = A problem was detected with the hemodialysis device.\n- Locate the ID code found in the bottom left corner\nof the alarm screen.\n- Call service to report the issue and schedule a repair.

[87]
Title     = Service Required: Dialysate Device
ListTitle = DG POST: Heat Cal
Message   = A problem was detected with the dialysate device.\n- Locate the ID code found in the bottom left corner\nof the alarm screen.\n- Call service to report the issue and schedule a repair.
SRSDG 929 = 

[88]
Title     = Service Required: Dialysate Device
ListTitle = DG Fault: CP1 CP2 Speed Range
Message   = A problem was detected with the dialysate device. \n- Treatment must be terminated.\n- Locate the ID code found in the bottom left corner\nof the alarm screen.\n- Call service to report the issue and schedule a repair.

[89]
Title     = Service Required: Dialysate Device
ListTitle = DG Fault: UVo On No Flow
Message   = A problem was detected with the dialysate device. \n- Treatment must be terminated.\n- Locate the ID code found in the bottom left corner\nof the alarm screen.\n- Call service to report the issue and schedule a repair.
SRSDG 599 = 

[90]
Title     = Service Required: Dialysate Device
ListTitle = DG Fault: LC A1/B1 Comm
Message   = A problem was detected with the dialysate device. \n- Treatment must be terminated.\n- Locate the ID code found in the bottom left corner\nof the alarm screen.\n- Call service to report the issue and schedule a repair.
SRSDG 604 = 

[91]
Title     = Communication Error
ListTitle = Loss of DG Comm (FMD)
Message   = A communication problem has been detected.\n- Treatment must be terminated.\n- Locate the ID code found in the bottom left corner\nof the alarm screen.\n- Call service to report the issue and schedule a repair.

[92]
Title     = 
ListTitle = 
Message   = 

[93]
Title     = Service Required: Dialysate Device
ListTitle = DG Fault: RO Permeate Cond High
Message   = A problem was detected with the dialysate device. \n- Treatment must be terminated.\n- Locate the ID code found in the bottom left corner\nof the alarm screen.\n- Call service to report the issue and schedule a repair.
SRSDG 430 = 

[94]
Title     = Service Required: Dialysate Device
ListTitle = DG Fault: Pressure Sensor Range
Message   = A problem was detected with the dialysate device. \n- Treatment must be terminated.\n- Locate the ID code found in the bottom left corner\nof the alarm screen.\n- Call service to report the issue and schedule a repair.
SRSDG 629 = 

[95]
Title     = Service Required: Dialysate Device
ListTitle = DG Fault: WD Error
Message   = A problem was detected with the dialysate device. \n- Treatment must be terminated.\n- Locate the ID code found in the bottom left corner\nof the alarm screen.\n- Call service to report the issue and schedule a repair.
SRSDG 907 = 

[96]
Title     = Incoming Water Temperature High
ListTitle = Dial. Gen: Inlet Water Temp High
Message   = Incoming water temperature is high.\n- Treatment is currently paused.\n- Check the incoming water supply.\n- When the temperature is within target range\nResume/OK button will be available.\n- Press Resume/OK to continue treatment.
SRSDG 410 = 

[97]
Title     = Conductivity Out of Range
ListTitle = Dial. Gen: Dialysate Cond.
Message   = Treatment is currently paused.\n- Confirm that acid and bicarbonate concentrates\nare securely connected.\n- If empty, replace. \n- Treatment will need to be resumed when conductivity\nis within target range.
SRSDG 397 = 

[98]
Title     = Service Required: Hemodialysis Device
ListTitle = HD Alarm (Low): Battery Com
Message   = A non- critical problem was detected with the hemodialysis\n device.\n- Call service to report the issue and schedule a repair.

[99]
Title     = Service Required: Hemodialysis Device
ListTitle = HD Fault: Syringe Pump Stall
Message   = A problem was detected with the hemodialysis device. \n- Treatment must be terminated.\n- Locate the ID code found in the bottom left corner\nof the alarm screen.\n- Call service to report the issue and schedule a repair.

[100]
Title     = Service Required: Dialysate Device
ListTitle = DG POST: Conductivity Cal
Message   = A problem was detected with the dialysate device.\n- Locate the ID code found in the bottom left corner\nof the alarm screen.\n- Call service to report the issue and schedule a repair.

[101]
Title     = Service Required: Hemodialysis Device
ListTitle = HD POST: UI- Proc Comm
Message   = A problem was detected with the hemodialysis device.\n- Locate the ID code found in the bottom left corner\nof the alarm screen.\n- Call service to report the issue and schedule a repair.

[102]
Title     = Disinfection Interrupted
ListTitle = Cleaning: Tpo THD Temp Delta
Message   = Disinfection terminated unexpectedly.\n- Restart disinfection.\n- If problem persists, call service to schedule a repair.
SRSDG 856
SRSDG 930 = 

[103]
Title     = Service Required: Hemodialysis Device
ListTitle = HD POST: Cal NVRAM CRC
Message   = A problem was detected with the hemodialysis device.\n- Locate the ID code found in the bottom left corner\nof the alarm screen.\n- Call service to report the issue and schedule a repair.

[104]
Title     = Service Required: Hemodialysis Device
ListTitle = HD Fault: Air Trap Sensor
Message   = A problem was detected with the hemodialysis device. \n- Treatment must be terminated.\n- Locate the ID code found in the bottom left corner\nof the alarm screen.\n- Call service to report the issue and schedule a repair.

[105]
Title     = Service Required: Dialysate Device
ListTitle = DG POST: Cal NVRAM CRC
Message   = A problem was detected with the dialysate device.\n- Locate the ID code found in the bottom left corner\nof the alarm screen.\n- Call service to report the issue and schedule a repair.
SRSDG 608 = 

[106]
Title     = Service Required: Dialysate Device
ListTitle = DG POST: Flow Sensor Cal
Message   = A problem was detected with the dialysate device.\n- Locate the ID code found in the bottom left corner\nof the alarm screen.\n- Call service to report the issue and schedule a repair.
SRSDG 820
SRSDG 821
SRSDG 1087 = 

[107]
Title     = Service Required: Dialysate Device
ListTitle = DG Fault: DG Restarted
Message   = A problem was detected with the dialysate device. \n- Treatment must be terminated.\n- Locate the ID code found in the bottom left corner\nof the alarm screen.\n- Call service to report the issue and schedule a repair.

[108]
Title     = Service Required: Hemodialysis Device
ListTitle = HD Fault: Syringe Pump ADC Com
Message   = A problem was detected with the hemodialysis device. \n- Treatment must be terminated.\n- Locate the ID code found in the bottom left corner\nof the alarm screen.\n- Call service to report the issue and schedule a repair.

[109]
Title     = Service Required: Hemodialysis Device
ListTitle = HD Fault: Syringe Pump Vol
Message   = A problem was detected with the hemodialysis device. \n- Treatment must be terminated.\n- Locate the ID code found in the bottom left corner\nof the alarm screen.\n- Call service to report the issue and schedule a repair.

[110]
Title     = Service Required: Hemodialysis Device
ListTitle = HD Fault: Syringe Pump Speed
Message   = A problem was detected with the hemodialysis device. \n- Treatment must be terminated.\n- Locate the ID code found in the bottom left corner\nof the alarm screen.\n- Call service to report the issue and schedule a repair.

[111]
Title     = Service Required: Hemodialysis Device
ListTitle = HD Fault: Syringe Pump Speed
Message   = A problem was detected with the hemodialysis device. \n- Treatment must be terminated.\n- Locate the ID code found in the bottom left corner\nof the alarm screen.\n- Call service to report the issue and schedule a repair.

[112]
Title     = Service Required: Dialysate Device
ListTitle = DG Fault: LC A2/B2 Comm
Message   = A problem was detected with the dialysate device. \n- Treatment must be terminated.\n- Locate the ID code found in the bottom left corner\nof the alarm screen.\n- Call service to report the issue and schedule a repair.
SRSDG 953 = 

[113]
Title     = Service Required: Dialysate Device
ListTitle = DG Fault: DRP Current
Message   = A problem was detected with the dialysate device. \n- Treatment must be terminated.\n- Locate the ID code found in the bottom left corner\nof the alarm screen.\n- Call service to report the issue and schedule a repair.
SRSDG 890 = 

[114]
Title     = Self Test: Venous Air Detector
ListTitle = Process: Pre- Tx Wet Self- Test
Message   = A problem has been detected with the venous air detector.\n- Check cartridge installation.\n- If problem persists, terminate treatment preparation and \n begin again using a new cartridge.

[115]
Title     = Service Required: Dialysate Device
ListTitle = DG Fault: Temp Sensor Range
Message   = A problem was detected with the dialysate device. \n- Treatment must be terminated.\n- Locate the ID code found in the bottom left corner\nof the alarm screen.\n- Call service to report the issue and schedule a repair.
SRSDG 224 = 

[116]
Title     = Service Required: Dialysate Device
ListTitle = HD Alarm (Low): SD- Card Error
Message   = A non- critical problem was detected with the hemodialysis\n device.\n- Call service to report the issue and schedule a repair.

[117]
Title     = Communication Error
ListTitle = Loss of HD Comm (HD ACK)
Message   = A communication problem has been detected.\n- Treatment must be terminated.\n- Locate the ID code found in the bottom left corner\nof the alarm screen.\n- Call service to report the issue and schedule a repair.
SRSDG 909 = 

[118]
Title     = Service Required: Dialysate Device
ListTitle = DG Fault: RTC Config
Message   = A problem was detected with the dialysate device. \n- Treatment must be terminated.\n- Locate the ID code found in the bottom left corner\nof the alarm screen.\n- Call service to report the issue and schedule a repair.
SRSDG 43 = 

[119]
Title     = Service Required: Dialysate Device
ListTitle = DG Alarm (Low): RTC Bat Low
Message   = A non- critical problem was detected with the dialysate device.\n- Call service to report the issue and schedule a repair.
SRSDG 908 = 

[120]
Title     = Self Test: Venous Air Detector
ListTitle = Process: Pre- Tx Wet Self- Test
Message   = A problem has been detected with the venous air detector\n- Check cartridge installation.\n- If problem persists, terminate treatment preparation and \n start over using a new cartridge.

[121]
Title     = Service Required: Dialysate Device
ListTitle = DG Fault: Prim Heater Lg Control
Message   = A problem was detected with the dialysate device. \n- Treatment must be terminated.\n- Locate the ID code found in the bottom left corner\nof the alarm screen.\n- Call service to report the issue and schedule a repair.
SRSDG 611 = 

[122]
Title     = Service Required: Dialysate Device
ListTitle = DG Fault: Prim Heater Sm Control
Message   = A problem was detected with the dialysate device. \n- Treatment must be terminated.\n- Locate the ID code found in the bottom left corner\nof the alarm screen.\n- Call service to report the issue and schedule a repair.
SRSDG 612 = 

[123]
Title     = Service Required: Dialysate Device
ListTitle = DG Fault: Trimmer Heater Control
Message   = A problem was detected with the dialysate device. \n- Treatment must be terminated.\n- Locate the ID code found in the bottom left corner\nof the alarm screen.\n- Call service to report the issue and schedule a repair.
SRSDG 613 = 

[124]
Title     = Blood Pump Stop Time Exceeded
ListTitle = Blood Stop: Blood Clot Risk
Message   = The blood pump has been off for too long.\n- Treatment must be terminated without rinseback.

[125]
Title     = Blood Pump Stop Time Exceeded
ListTitle = Blood Stop: Blood Clot Risk
Message   = The blood pump has been off for too long.\n- Treatment must be terminated without rinseback.

[126]
Title     = Blood Leak
ListTitle = Blood Stop: Dialyzer Blood Leak
Message   = A blood leak has been detected. \n- Visually inspect dialysate return line for blood.\n- Press Resume/OK to proceed to the next step. Dialysate will\n remain in bypass.

[127]
Title     = Low Venous Pressure
ListTitle = Blood Stop: Venous Pres. Low
Message   = Venous pressure is low.\n- Ensure venous access connections are properly secured.\n- Check needle placement and resolve access issues, \nif applicable.\n- Check air trap for foam and that transducers are secured.\n- Inspect transducer for moisture and change, if applicable.\n- Inspect dialyzer for clots. If clots are present, follow\n facility policy to end treatment.\n- Press Resume/OK to continue treatment.

[128]
Title     = Venous Air Detected
ListTitle = Blood Stop: Venous Air Bubble
Message   = Air detected in the venous air trap.\n- Confirm arterial access placement and confirm\nconnections are secure.\n- Treatment must be terminated without rinseback.

[129]
Title     = Blood Leak: Bypass
ListTitle = Blood Stop: Dialyzer Blood Leak Bypass
Message   = The device is currently in bypass due to a potential blood leak.\n- If blood is present upon visual inspection, press\n END TREATMENT to terminate treatment without rinseback.\n- If blood is not visualized, check dialysate for blood using\n test strip.\n- Follow facility policy to Resume/OK or END TREATMENT.

[130]
Title     = High Venous Pressure
ListTitle = Blood Stop: Venous Pres. High
Message   = Venous pressure is high. \n- Check venous bloodlines for kinks or clamps.\n- Check needle placement and/or access position.\n- Resolve access issues, if applicable.\n- Check air trap for foam and that transducers are secured.\n- Inspect transducer for moisture and change, if applicable.\n- If clots are present, end treatment without rinseback.\n- Press Resume/OK to continue treatment.

[131]
Title     = Low Arterial Pressure
ListTitle = Blood Stop: Arterial Pres. Low
Message   = Arterial pressure is low.\n- Inspect arterial bloodlines for kinks or clamps.\n- Check needle placement or access position.\n- Resolve access issues, if applicable.\n- Check to ensure transducers are securely connected.\n- Inspect transducer for moisture and change if applicable.\n- If clots are present, end treatment without rinseback.

[132]
Title     = High Arterial Pressure
ListTitle = Blood Stop: Arterial Pres. High
Message   = Arterial pressure is high.\n- Check venous bloodlines for kinks or clamps.\n- Check needle placement and/or access position.\n- Resolve access issues if applicable.\n- Check to ensure transducers are securely connected.\n- Inspect transducer for moisture and change if applicable.\n- If clots are present, end treatment without rinseback.

[133]
Title     = Dialysate Device Fluid Leak
ListTitle = DG Fault: Fluid Leak in DG
Message   = Fluid leak detected in the dialysate device.\n- Treatment must be terminated.\n- Turn off water source. \n- Disconnect water and electrical connections from the device.\n- Locate the ID code found in the bottom left corner\nof the alarm screen.\n- Call service to report the issue and schedule a repair.
SRSDG 328 = 

[134]
Title     = Fluid Leak
ListTitle = Blood Stop: Fluid Leak in HD
Message   = Fluid leak detected in hemodialysis device.\n- If in treatment, blood pump is off.\n- Identify and correct the cause of the fluid leak.\n- Clean up fluid and dry leak sensor.\n- Once fluid has been cleaned up, Resume/OK treatment.

[135]
Title     = Blood Pump Stopped: Excessive Movement
ListTitle = Blood Stop: HD Shock Detected
Message   = Excessive movement of the hemodialysis device has been\ndetected. \n- Treatment is currently paused.  \n- When system movement has stablized, \ntreatment will need to be resumed.\n- To resume treatment, press Resume/OK.

[136]
Title     = Dialysate Device: Excessive Movement
ListTitle = Dial. Gen: Shock- Vibration
Message   = Excessive movement of the dialysate device has been\ndetected. \n- Treatment is currently paused.  \n- When system movement has stablized, \ntreatment will need to be resumed.\n- To resume treatment, press Resume/OK.
SRSDG 327 = 

[137]
Title     = Blood Pump Stopped: Excessive Tilt
ListTitle = Blood Stop: HD Tilted
Message   = Excessive tilt of the hemodialysis device has been detected. \n- Treatment is currently paused.  \n- When the device is stationary and level, \ntreatment will need to be resumed.\n- To resume treatment, press Resume/OK.

[138]
Title     = Dialysate Device: Excessive Tilt
ListTitle = Dial. Gen: Tilt
Message   = Excessive tilt of the dialysate device has been detected.\n- Treatment is paused.\n- Confirm the device is stationary and level before continuing.
SRSDG 326 = 

[139]
Title     = Power Loss
ListTitle = Loss of AC Power
Message   = AC Power has been lost.\n- Check all electrical connections.\n- Press Resume/OK to return to welcome screen.

[140]
Title     = Communication Error
ListTitle = Loss of DG Comm (Timeout)
Message   = A communication problem has been detected.\n- Treatment must be terminated.\n- Locate the ID code found in the bottom left corner\nof the alarm screen.\n- Call service to report the issue and schedule a repair.

[141]
Title     = Blood Pump Stopped: Venous Air Detector
ListTitle = Blood Stop: Air Trap Fill
Message   = A problem was detected with the venous air detector.\n- Confirm arterial access placement and ensure\nconnections are secure.\n- Treatment must be terminated without rinseback.

[142]
Title     = Blood Pump Stopped: Occlusion
ListTitle = Blood Stop: Blood Pump Occlusion
Message   = Occlusion detected after the blood pump.\n- Inspect bloodlines for kinks or clamps.\n- Check needle placement or access position.\n- Resolve access issues, if applicable.\n- If clots are present, end treatment without rinseback.

[143]
Title     = Service Required: Dialysate Device
ListTitle = DG Fault: TRo TDi Delta
Message   = A problem was detected with the dialysate device. \n- Treatment must be terminated.\n- Locate the ID code found in the bottom left corner\nof the alarm screen.\n- Call service to report the issue and schedule a repair.
SRSDG 912 = 

[144]
Title     = Disinfection: Water Conductivity High
ListTitle = Cleaning: Inlet Water Cond High
Message   = Incoming water conductivity is too high.\n- Disinfection has been terminated.\n- Check incoming water before initiating disinfection again.
SRSDG 1066
SRSDG 1054
SRSDG 970 = 

[145]
Title     = Conductivity Error During Prime
ListTitle = Dial. Gen: Acid Conc. Cond.
Message   = Conductivity out of range during prime.\n- Confirm that acid and bicarbonate concentrates\nare securely connected.\n- If empty, replace. \n- Treatment will need to be resumed when conductivity\nis within target range.
SRSDG 846 = 

[146]
Title     = Service Required: Dialysate Device
ListTitle = DG POST: DG RTC Timer
Message   = A problem was detected with the dialysate device.\n- Locate the ID code found in the bottom left corner\nof the alarm screen.\n- Call service to report the issue and schedule a repair.
SRSDG 312 = 

[147]
Title     = Dialysate Generation Error
ListTitle = Dial. Gen: Dialysate not ready
Message   = A problem has been detected with dialysate generation. \n- Treatment is paused and will need to be resumed when \nthe dialysate is ready for use.
SRSDG 398 = 

[148]
Title     = Disinfection: Water Temperature High
ListTitle = Cleaning: Inlet Water Temp High
Message   = Incoming water temperature is too high.\n- Disinfection has been terminated.\n- Check incoming water before initiating disinfection again.
SRSDG 1065
SRSDG 1053
SRSDG 969 = 

[149]
Title     = Service Required: Hemodialysis Device
ListTitle = HD Fault: WD Error
Message   = A problem was detected with the hemodialysis device. \n- Treatment must be terminated.\n- Locate the ID code found in the bottom left corner\nof the alarm screen.\n- Call service to report the issue and schedule a repair.

[150]
Title     = Incoming Water Conductivity High
ListTitle = Dial. Gen: Inlet Water Cond High
Message   = Conductivity of incoming water is high.\n- Treatment is currently paused.\n- Check the incoming water supply.\n- When the conductivity is within target range\nResume/OK button will be available.\n- Press Resume/OK to continue treatment.
SRSDG 391 = 

[151]
Title     = Incoming Water Conductivity Low
ListTitle = Dial. Gen: Inlet Water Cond Low
Message   = Conductivity of incoming water is low.\n- Treatment is currently paused.\n- Check the incoming water supply.\n- When the conductivity is within target range\nResume/OK button will be available.\n- Press Resume/OK to continue treatment.
SRSDG 826 = 

[152]
Title     = Incoming Water Pressure Low
ListTitle = Dial. Gen: Inlet Water Pres Low
Message   = Water pressure of incoming water is low.\n- Treatment is currently paused.\n- Check the incoming water supply.\n- When the pressure is within target range\nResume/OK button will be available.\n- Press Resume/OK to continue treatment.
SRSDG 417 = 

[153]
Title     = Pre-Treatment Process Terminated
ListTitle = Process: Pre- Tx Terminated
Message   = The pre- treatment process has been terminated because \ntreatment did not begin within two hours of priming. \n- Press Resume/OK for continue with next steps to remove \ncartridge from the device.

[154]
Title     = Disinfection: Water Conductivity Low
ListTitle = Cleaning: Inlet Water Cond Low
Message   = Incoming water conductivity is too low.\n- Disinfection has been terminated.\n- Check incoming water before initiating disinfection again.
SRSDG 1067
SRSDG 1055
SRSDG 971 = 

[155]
Title     = Communication Error
ListTitle = Loss of DG Comm (Reservoir)
Message   = A communication problem has been detected.\n- Treatment must be terminated.\n- Locate the ID code found in the bottom left corner\nof the alarm screen.\n- Call service to report the issue and schedule a repair.

[156]
Title     = Communication Error
ListTitle = Loss of DG Comm (Op Mode)
Message   = A communication problem has been detected.\n- Treatment must be terminated.\n- Locate the ID code found in the bottom left corner\nof the alarm screen.\n- Call service to report the issue and schedule a repair.

[157]
Title     = Chemical Disinfectant Not Detected
ListTitle = Cleaning: Chem Disinf PAA Prime
Message   = Unable to sense proper chemical disinfectant.\n- Disinfection process has terminated.\n- Confirm chemical disinfectant is connected to the\nconcentrate inlet. \n- Confirm chemical disinfectant container is not empty.\n- Restart disinfection.\n- If problem persists, call service to schedule a repair.
SRSDG 988 = 

[158]
Title     = Incoming Water Temperature Low
ListTitle = Dial. Gen: Inlet Water Temp Low
Message   = Incoming water temperature is low.\n- Treatment is currently paused.\n- Check the incoming water supply.\n- When the temperature is within target range\nResume/OK button will be available.\n- Press Resume/OK to continue treatment.
SRSDG 408 = 

[159]
Title     = Remove Chemical Disinfectant
ListTitle = Cleaning: Chem Disinf Connect Cap
Message   = The chemical disinfectant is no longer needed. \n- Disconnect chemical disinfectant from the device. \n- Place the concentrate connection cap on the device.\n- Keep dialysate cap on the device.
SRSDG 1044 = 

[160]
Title     = Service Required: Hemodialysis Device
ListTitle = HD Fault: BP Rotor Max Speed
Message   = A problem was detected with the hemodialysis device. \n- Treatment must be terminated.\n- Locate the ID code found in the bottom left corner\nof the alarm screen.\n- Call service to report the issue and schedule a repair.

[161]
Title     = Service Required: Dialysate Device
ListTitle = DG Fault: HD- DG Comm
Message   = A problem was detected with the dialysate device. \n- Treatment must be terminated.\n- Locate the ID code found in the bottom left corner\nof the alarm screen.\n- Call service to report the issue and schedule a repair.
SRSDG 122 = 

[162]
Title     = Service Required: Dialysate Device
ListTitle = DG Fault: Proc- FPGA Clock
Message   = A problem was detected with the dialysate device. \n- Treatment must be terminated.\n- Locate the ID code found in the bottom left corner\nof the alarm screen.\n- Call service to report the issue and schedule a repair.
SRSDG 867 = 

[163]
Title     = Ultrafiltration Error
ListTitle = Dial. Gen: UF Rate Check
Message   = A problem was detected with the dialysate device. \n- Confirm the device is level with minimal movement. \n- Resume/OK treatment. \n- If problem persists, call service to report the issue and\nschedule a repair.

[164]
Title     = Ultrafiltration Error
ListTitle = Dial. Gen: UF Rate Check
Message   = A problem was detected with the dialysate device. \n- Confirm the device is level with minimal movement. \n- Resume/OK treatment. \n- If problem persists, call service to report the issue and\nschedule a repair.

[165]
Title     = Blood Pump Stop Time Exceeded
ListTitle = Blood Stop: Blood Clot Risk
Message   = The blood pump has been off for too long.\n- Treatment must be terminated without rinseback.

[166]
Title     = Test Alarm - Alarm 166
ListTitle = 
Message   = 

[167]
Title     = Blood Pump Stopped: Door Open
ListTitle = Blood Stop: Door Open
Message   = The device door is open.\n Close the device door. \n- Press Resume/OK to continue.

[168]
Title     = Test Alarm - Alarm 168
ListTitle = 
Message   = 

[169]
Title     = Service Required: Dialysate Device
ListTitle = DG Fault: Dialysate Flow Sens Rg
Message   = A problem was detected with the dialysate device. \n- Treatment must be terminated.\n- Locate the ID code found in the bottom left corner\nof the alarm screen.\n- Call service to report the issue and schedule a repair.
SRSDG 643 = 

[170]
Title     = Heparin Syringe Empty
ListTitle = Heparin Syringe Empty
Message   = Heparin syringe is empty.\n- Treatment will continue without heparin.\n- Refer to facility policy if additional heparin is needed to\ncomplete treatment.

[171]
Title     = Heparin Pump Occlusion
ListTitle = Process: Pre- Tx Hep. Pump Occ.
Message   = A problem has been detected with the heparin pump.\n- Ensure heparin line is not kinked or clamped.

[172]
Title     = Not Enough Heparin
ListTitle = Process: Pre- Tx Not Enough Hep.
Message   = There is not enough heparin available for treatment.\n- Ensure the syringe pump is touching the syringe plunger.\n- If the syringe pump is touching the syringe plunger,\nend treatment.\n- If syringe pump is not touching the syringe plunger, \nensure the correct amount of heparin has been drawn and\nreload the syringe.

[173]
Title     = Service Required: Hemodialysis Device
ListTitle = HD Fault: RTC Config
Message   = A problem was detected with the hemodialysis device. \n- Treatment must be terminated.\n- Locate the ID code found in the bottom left corner\nof the alarm screen.\n- Call service to report the issue and schedule a repair.

[174]
Title     = Service Required: Hemodialysis Device
ListTitle = HD POST: HD RTC Timer
Message   = A problem was detected with the hemodialysis device.\n- Locate the ID code found in the bottom left corner\nof the alarm screen.\n- Call service to report the issue and schedule a repair.

[175]
Title     = Service Required: Hemodialysis Device
ListTitle = HD Fault: Pump Commutation Err
Message   = A problem was detected with the hemodialysis device. \n- Treatment must be terminated.\n- Locate the ID code found in the bottom left corner\nof the alarm screen.\n- Call service to report the issue and schedule a repair.

[176]
Title     = Test Alarm - Alarm 176
ListTitle = 
Message   = 

[177]
Title     = Service Required: Dialysate Device
ListTitle = DG Fault: Software Invalid State
Message   = A problem was detected with the dialysate device. \n- Treatment must be terminated.\n- Locate the ID code found in the bottom left corner\nof the alarm screen.\n- Call service to report the issue and schedule a repair.
SRSDG 919 = 

[178]
Title     = Service Required: Hemodialysis Device
ListTitle = HD Fault: UI- Proc Comm
Message   = A problem was detected with the hemodialysis device.\n- Locate the ID code found in the bottom left corner\nof the alarm screen.\n- Call service to report the issue and schedule a repair.
 = SRSUI 1066

[179]
Title     = Service Required: Dialysate Device
ListTitle = DG Fault: FPGA Com
Message   = A problem was detected with the dialysate device. \n- Treatment must be terminated.\n- Locate the ID code found in the bottom left corner\nof the alarm screen.\n- Call service to report the issue and schedule a repair.
SRSDG 605 = 

[180]
Title     = Service Required: Dialysate Device
ListTitle = DG Fault: RO Flow Sensor Range
Message   = A problem was detected with the dialysate device. \n- Treatment must be terminated.\n- Locate the ID code found in the bottom left corner\nof the alarm screen.\n- Call service to report the issue and schedule a repair.
SRSDG 883 = 

[181]
Title     = Service Required: Dialysate Device
ListTitle = DG Fault: Tare Out of Range
Message   = A problem was detected with the dialysate device. \n- Treatment must be terminated.\n- Locate the ID code found in the bottom left corner\nof the alarm screen.\n- Call service to report the issue and schedule a repair.
SRSDG 849
SRSDG 838 = 

[182]
Title     = Service Required: Dialysate Device
ListTitle = DG POST: LC Cal
Message   = A problem was detected with the dialysate device.\n- Locate the ID code found in the bottom left corner\nof the alarm screen.\n- Call service to report the issue and schedule a repair.
SRSDG 162 = 

[183]
Title     = Disinfection Interrupted
ListTitle = Cleaning: Invalid Resv Transfer
Message   = Disinfection terminated unexpectedly.\n- Restart disinfection.\n- If problem persists, call service to schedule a repair.
SRSDG 851 = 

[184]
Title     = Service Required: Dialysate Device
ListTitle = DG Fault: UVi Error
Message   = A problem was detected with the dialysate device. \n- Treatment must be terminated.\n- Locate the ID code found in the bottom left corner\nof the alarm screen.\n- Call service to report the issue and schedule a repair.
SRSDG 559 = 

[185]
Title     = Service Required: Dialysate Device
ListTitle = DG Alarm (Low): Fan Speed
Message   = A non- critical problem was detected with the dialysate device.\n- Call service to report the issue and schedule a repair.
SRSDG 628 = 

[186]
Title     = Service Required: Dialysate Device
ListTitle = DG Fault: CP1/CP2 Fault
Message   = A problem was detected with the dialysate device. \n- Treatment must be terminated.\n- Locate the ID code found in the bottom left corner\nof the alarm screen.\n- Call service to report the issue and schedule a repair.
SRSDG 891 = 

[187]
Title     = Service Required: Dialysate Device
ListTitle = DG Fault: CP1 Speed Fault
Message   = A problem was detected with the dialysate device. \n- Treatment must be terminated.\n- Locate the ID code found in the bottom left corner\nof the alarm screen.\n- Call service to report the issue and schedule a repair.
SRSDG 905 = 

[188]
Title     = Service Required: Dialysate Device
ListTitle = DG Fault: CP2 Speed Fault
Message   = A problem was detected with the dialysate device. \n- Treatment must be terminated.\n- Locate the ID code found in the bottom left corner\nof the alarm screen.\n- Call service to report the issue and schedule a repair.
SRSDG 906 = 

[189]
Title     = Service Required: Dialysate Device
ListTitle = DG Fault: DRP Speed Fault
Message   = A problem was detected with the dialysate device. \n- Treatment must be terminated.\n- Locate the ID code found in the bottom left corner\nof the alarm screen.\n- Call service to report the issue and schedule a repair.
SRSDG 448 = 

[190]
Title     = Service Required: Dialysate Device
ListTitle = DG Fault: DRP Speed Not Off
Message   = A problem was detected with the dialysate device. \n- Treatment must be terminated.\n- Locate the ID code found in the bottom left corner\nof the alarm screen.\n- Call service to report the issue and schedule a repair.

[191]
Title     = Service Required: Dialysate Device
ListTitle = DG Fault: RO Flow High
Message   = A problem was detected with the dialysate device. \n- Treatment must be terminated.\n- Locate the ID code found in the bottom left corner\nof the alarm screen.\n- Call service to report the issue and schedule a repair.
SRSDG 885 = 

[192]
Title     = Service Required: Dialysate Device
ListTitle = DG Fault: RO Flow Low
Message   = A problem was detected with the dialysate device. \n- Treatment must be terminated.\n- Locate the ID code found in the bottom left corner\nof the alarm screen.\n- Call service to report the issue and schedule a repair.
SRSDG 945 = 

[193]
Title     = Blood Pump Stopped: Partial Occlusion
ListTitle = Blood Stop: Blood Pump Partial Occlusion
Message   = Partial occlusion detected after the blood pump.\n- Inspect bloodlines for kinks or clamps.\n- Check needle placement or access position.\n- Resolve access issues, if applicable.\n- Inspect dialyzer for clots. If clots are present, follow\n facility policy to end treatment.

[194]
Title     = Service Required: Dialysate Device
ListTitle = DG Fault: RO Driver Feedback
Message   = A problem was detected with the dialysate device. \n- Treatment must be terminated.\n- Locate the ID code found in the bottom left corner\nof the alarm screen.\n- Call service to report the issue and schedule a repair.
SRSDG 881 = 

[195]
Title     = Service Required: Dialysate Device
ListTitle = DG Fault: RO Pump High Pressure
Message   = A problem was detected with the dialysate device. \n- Treatment must be terminated.\n- Locate the ID code found in the bottom left corner\nof the alarm screen.\n- Call service to report the issue and schedule a repair.
SRSDG 925 = 

[196]
Title     = Service Required: Dialysate Device
ListTitle = DG Fault: CPi/CPo Comm
Message   = A problem was detected with the dialysate device. \n- Treatment must be terminated.\n- Locate the ID code found in the bottom left corner\nof the alarm screen.\n- Call service to report the issue and schedule a repair.
SRSDG 955 = 

[197]
Title     = Service Required: Dialysate Device
ListTitle = DG Fault: CD1/CD2 Comm
Message   = A problem was detected with the dialysate device. \n- Treatment must be terminated.\n- Locate the ID code found in the bottom left corner\nof the alarm screen.\n- Call service to report the issue and schedule a repair.
SRSDG 956 = 

[198]
Title     = Service Required: Dialysate Device
ListTitle = DG Fault: HP On With No Flow
Message   = A problem was detected with the dialysate device. \n- Treatment must be terminated.\n- Locate the ID code found in the bottom left corner\nof the alarm screen.\n- Call service to report the issue and schedule a repair.
SRSDG 872 = 

[199]
Title     = Service Required: Dialysate Device
ListTitle = DG Fault: HR On With No Flow
Message   = A problem was detected with the dialysate device. \n- Treatment must be terminated.\n- Locate the ID code found in the bottom left corner\nof the alarm screen.\n- Call service to report the issue and schedule a repair.
SRSDG 871 = 

[200]
Title     = Service Required: Dialysate Device
ListTitle = DG Fault: Thermistor Range
Message   = A problem was detected with the dialysate device. \n- Treatment must be terminated.\n- Locate the ID code found in the bottom left corner\nof the alarm screen.\n- Call service to report the issue and schedule a repair.
SRSDG 178 = 

[201]
Title     = Self Test: Dialysate Flow Rate
ListTitle = Process: Pre- Tx Wet Self- Test
Message   = A problem has been detected when measuring dialysate flow.\n- Confirm cartridge is properly installed and primed.\n- If problem persists, terminate treatment preparation and \n start over using a new cartridge.

[202]
Title     = Self Test: Pressure
ListTitle = Process: Pre- Tx Dry Self- Test
Message   = A problem has been detected during self- test. \n- Confirm the cartridge is properly installed. \n- Ensure arterial and venous pressure sensor lines are\nnot kinked.\n- Press Resume/OK to resume. \n- If problem persists, install a new cartridge.

[203]
Title     = Service Required: Dialysate Device
ListTitle = DG POST: Fill Cond Cal
Message   = A problem was detected with the dialysate device.\n- Locate the ID code found in the bottom left corner\nof the alarm screen.\n- Call service to report the issue and schedule a repair.

[204]
Title     = Service Required: Dialysate Device
ListTitle = DG Fault: RO Rejection
Message   = A problem was detected with the dialysate device. \n- Treatment must be terminated.\n- Locate the ID code found in the bottom left corner\nof the alarm screen.\n- Call service to report the issue and schedule a repair.
SRSDG 429 = 

[205]
Title     = Service Required: Dialysate Device
ListTitle = DG Fault: Cond Sensors Error
Message   = A problem was detected with the dialysate device. \n- Treatment must be terminated.\n- Locate the ID code found in the bottom left corner\nof the alarm screen.\n- Call service to report the issue and schedule a repair.
SRSDG 913 = 

[206]
Title     = Service Required: Dialysate Device
ListTitle = DG Fault: Reservoir Fill Timeout
Message   = A problem was detected with the dialysate device. \n- Treatment must be terminated.\n- Locate the ID code found in the bottom left corner\nof the alarm screen.\n- Call service to report the issue and schedule a repair.
SRSDG 437 = 

[207]
Title     = Service Required: Dialysate Device
ListTitle = DG Fault: FMP Flow Rate Error
Message   = A problem was detected with the dialysate device. \n- Treatment must be terminated.\n- Locate the ID code found in the bottom left corner\nof the alarm screen.\n- Call service to report the issue and schedule a repair.
SRSDG 240 = 

[208]
Title     = High Venous Pressure
ListTitle = Blood Stop: Venous Pres. High
Message   = Venous pressure is high. \n- Check venous bloodlines for kinks or clamps.\n- Check needle placement and/or access position.\n- Resolve access issues, if applicable.\n- If clots are present, end treatment without rinseback.

[209]
Title     = Disinfection Interrupted
ListTitle = Cleaning: Flush Circ Error
Message   = Disinfection terminated unexpectedly.\n- Restart disinfection.\n- If problem persists, call service to schedule a repair.
SRSDG 980 = 

[210]
Title     = Service Required: Hemodialysis Device
ListTitle = HD Alarm (Low): Battery Fault
Message   = A non- critical problem was detected with the hemodialysis\n device.\n- Call service to report the issue and schedule a repair.

[211]
Title     = Approaching MAX Blood Pump Stop Time
ListTitle = Blood Stopped:  Warning
Message   = The blood has been stopped for nearly 5 minutes.\n- You must resume treatment before the blood pump stop time\ntimer expires.\n- If treatment is not resumed before the timer expires,\ntreatment will be terminated without rinseback.

[212]
Title     = Approaching MAX Blood Pump Stop Time
ListTitle = Blood Stopped:  Warning
Message   = The blood has been stopped for nearly 5 minutes.\n- You must Resume/OK treatment before the blood pump stop \ntime timer expires.\n- If treatment is not Resume/OK before the timer expires,\ntreatment will be terminated without rinseback.

[213]
Title     = Prime Complete - 30 MIN WARNING
ListTitle = Process: Pre- Tx Prime Complete
Message   = The priming process completed 90 minutes ago. \n- Treatment must begin within 30 minutes or the\npre- treatment process will be terminated.\n- Press Resume/OK to continue.

[214]
Title     = Service Required: Dialysate Device
ListTitle = DG POST: Conc Pump Cal
Message   = A problem was detected with the dialysate device.\n- Locate the ID code found in the bottom left corner\nof the alarm screen.\n- Call service to report the issue and schedule a repair.

[215]
Title     = 
ListTitle = 
Message   = 

[216]
Title     = Treatment Complete
ListTitle = Process: End of Dialysis Tx
Message   = Dialysis treatment is complete.\n- Press RINSEBACK to end treatment and rinseback.

[217]
Title     = 
ListTitle = 
Message   = 

[218]
Title     = Syringe Detected
ListTitle = Process: Remove Syringe
Message   = Heparin syringe was not removed from device.\n- Remove heparin syringe.\n- Press Resume/OK to continue.

[219]
Title     = Blood Stopped: Syringe Not Detected
ListTitle = Blood Stop: Syringe Not Detected
Message   = There is a problem detecting a syringe in the heparin pump.\n- Confirm the heparin syringe is properly installed. \n- Press Resume/OK to resume treatment.

[220]
Title     = Service Required: Dialysate Device
ListTitle = DG Fault: THD RTD Comm
Message   = A problem was detected with the dialysate device. \n- Treatment must be terminated.\n- Locate the ID code found in the bottom left corner\nof the alarm screen.\n- Call service to report the issue and schedule a repair.
SRSDG 947 = 

[221]
Title     = Blood Pump Stopped: Saline Bag Empty
ListTitle = Blood Stop: Saline Bag Empty
Message   = The saline bag appears empty.\n- Check the saline bag and replace if empty.

[222]
Title     = Service Required: Hemodialysis Device
ListTitle = HD Fault: BP Occ Com
Message   = A problem was detected with the hemodialysis device. \n- Treatment must be terminated.\n- Locate the ID code found in the bottom left corner\nof the alarm screen.\n- Call service to report the issue and schedule a repair.

[223]
Title     = Service Required: Hemodialysis Device
ListTitle = HD Fault: Art. Pres. Com
Message   = A problem was detected with the hemodialysis device. \n- Treatment must be terminated.\n- Locate the ID code found in the bottom left corner\nof the alarm screen.\n- Call service to report the issue and schedule a repair.

[224]
Title     = Blood Pump Stopped: Treatment Paused
ListTitle = Blood Stopped: Treatment Pause
Message   = Treatment has been stopped by user.\n- Press Resume/OK to resume treatment. \n- If treatment is not resumed within five minutes,\ntreatment will be terminated without rinseback.

[225]
Title     = Treatment Complete
ListTitle = Process: End of Treatment
Message   = Dialysis treatment is complete.\n- If blood sampling is required, draw blood at\n the arterial sample port\n- Press RINSEBACK to end treatment and rinseback.

[226]
Title     = Priming Complete
ListTitle = Process: Pre- Tx Priming Complete
Message   = Priming is complete. \n- Treatment must begin within 120 minutes \nor the pre- treatment process will be terminated.\n- Press Resume/OK to continue.

[227]
Title     = 
ListTitle = 
Message   = 

[228]
Title     = Priming Error
ListTitle = Process: Pre- Tx Prime Timeout
Message   = A problem has been detected during prime. \n- Prime was unable to complete. \n - Check blood and dialysate lines for clamps, kinks or leaks.

[229]
Title     = Priming Error
ListTitle = Process: Pre- Tx Prime Timeout
Message   = A problem has been detected during prime. \n- Prime was unable to complete. \n - Check blood and dialysate lines for clamps, kinks or leaks.

[230]
Title     = Priming Error
ListTitle = Process: Pre- Tx Prime Timeout
Message   = A problem has been detected during prime. \n- Prime was unable to complete. \n - Check blood and dialysate lines for clamps, kinks or leaks.

[231]
Title     = Self Test: Cartridge Check
ListTitle = Process: Pre- Tx Dry Self- Test
Message   = A problem has been detected during self- test. \n- Confirm cartridge is properly installed without kinks or clamps.\n- Ensure all connections are secure. \n- Press Resume/OK to resume. \n- If problem persists, install a new cartridge.

[232]
Title     = Self Test: Dialysate Flow Rate
ListTitle = Process: Pre- Tx Wet Self- Test
Message   = A problem has been detected when measuring dialysate flow.\n- Confirm cartridge is properly installed and primed.\n- If problem persists, terminate treatment preparation and \n start over using a new cartridge.

[233]
Title     = Service Required: Dialysate Device
ListTitle = DG Fault: Baro Cal CRC
Message   = A problem was detected with the dialysate device. \n- Treatment must be terminated.\n- Locate the ID code found in the bottom left corner\nof the alarm screen.\n- Call service to report the issue and schedule a repair.
SRSDG 964
SRSDG 949
SRSDG 1089 = 

[234]
Title     = Incoming Water Pressure High
ListTitle = Dial. Gen: Inlet Water Pres High
Message   = Incoming water pressure is high.\n- Treatment is currently paused.\n- Check the incoming water supply.\n- When the pressure is within target range\nResume/OK button will be available.\n- Press Resume/OK to continue treatment.
SRSDG 1037 = 

[235]
Title     = Rinseback Complete
ListTitle = Process: Rinseback Complete
Message   = Rinseback is complete. \n- Follow facililty policy prior to disconnecting patient. \n- Press Resume/OK to continue.

[236]
Title     = Self Test: Fluid Present
ListTitle = Process: Pre- Tx Dry Self- Test
Message   = A problem has been detected during self- test.  \n- Cartridges are single- use only and fluid is present.\n- Install new cartridge to resume.

[237]
Title     = 
ListTitle = 
Message   = 

[238]
Title     = Cartridge Not Detected
ListTitle = Process: Pre- Tx Dry Self- Test
Message   = A problem has been detected during self- test. \n- Cartridge is not detected.\n- Confirm cartridge is properly installed.

[239]
Title     = Cartridge Still Detected
ListTitle = Process: Post- Tx Remove Cartridge
Message   = A problem has been detected during self- test. \n- Cartridge is still present or was unloaded incorrectly.\n- Confirm the cartridge has been fully removed.

[240]
Title     = Conductivity Error During Prime
ListTitle = Dial. Gen: Bicarb Conc. Cond.
Message   = Conductivity out of range during prime.\n- Confirm that acid and bicarbonate concentrates\nare securely connected.\n- If empty, replace. \n- Treatment will need to be resumed when conductivity\nis within target range.
SRSDG 482 = 

[241]
Title     = Disinfection Interrupted
ListTitle = Cleaning: Resv Drain Timeout
Message   = Disinfection terminated unexpectedly.\n- Restart disinfection.\n- If problem persists, call service to schedule a repair.
SRSDG 848
SRSDG 90
SRSDG 561
SRSDG 577
SRSDG 590
SRSDG 591
SRSDG 336
SRSDG 879
SRSDG 340
SRSDG 496
SRSDG 501
SRSDG 505
SRSDG 532
SRSDG 535
SRSDG 556
SRSDG 557
SRSDG 1048
SRSDG 1049
SRSDG 651
SRSDG 655
SRSDG 744
SRSDG 745
SRSDG 1004
SRSDG 1008
SRSDG 1019
SRSDG 1023
SRSDG 1033
SRSDG 1034 = 

[242]
Title     = Disinfection Interrupted
ListTitle = Cleaning: Resv Fill Timeout
Message   = Disinfection terminated unexpectedly.\n- Restart disinfection.\n- If problem persists, call service to schedule a repair.
SRSDG 850
SRSDG 573
SRSDG 574
SRSDG 579
SRSDG 580
SRSDG 492
SRSDG 493
SRSDG 498
SRSDG 499
SRSDG 508
SRSDG 509
SRSDG 519
SRSDG 690
SRSDG 691
SRSDG 703
SRSDG 711
SRSDG 1020
SRSDG 1024 = 

[243]
Title     = Disinfection Interrupted
ListTitle = Cleaning: Fluid Loss Detected
Message   = Disinfection terminated unexpectedly.\n- Restart disinfection.\n- If problem persists, call service to schedule a repair.
SRSDG 853 = 

[244]
Title     = Disinfection Interrupted
ListTitle = Cleaning: Temp Sensor Check
Message   = Disinfection terminated unexpectedly.\n- Restart disinfection.\n- If problem persists, call service to schedule a repair.
SRSDG 852 = 

[245]
Title     = Disinfection Interrupted
ListTitle = Cleaning: Heat Disinfect Temp TO
Message   = Disinfection terminated unexpectedly.\n- Restart disinfection.\n- If problem persists, call service to schedule a repair.
SRSDG 854 = 

[246]
Title     = Disinfection Interrupted
ListTitle = Cleaning: RO Water Cond Error
Message   = Disinfection terminated unexpectedly.\n- Restart disinfection.\n- If problem persists, call service to schedule a repair.

[247]
Title     = 
ListTitle = 
Message   = 

[248]
Title     = Disinfection Interrupted
ListTitle = Cleaning: Chem Disinfect Proc
Message   = Disinfection terminated unexpectedly.\n- Restart disinfection.\n- If problem persists, call service to schedule a repair.

[249]
Title     = Chemical Disinfectant Not Detected
ListTitle = Cleaning: Chem Disinf PAA Cond
Message   = Unable to sense proper chemical disinfectant.\n- Disinfection process has terminated.\n- Confirm chemical disinfectant is connected to the\nconcentrate inlet.\n- Confirm chemical disinfectant container is not empty.\n- Restart disinfection.\n- If problem persists, call service to schedule a repair.
SRSDG 992 = 

[250]
Title     = Connect Chemical Disinfectant
ListTitle = Cleaning: Chem Disinf Connect PAA
Message   = Connect chemical disinfectant to the device. \n- Remove concentrate cap.\n- Keep dialysate cap on the device.\n- Place disinfectant straw in the disinfectant bottle. \n- Attach straw to concentrate connection and ensure\nconnection is secure.\n- Press Resume/OK to continue.
SRSDG 1046 = 

[251]
Title     = Service Required: Hemodialysis Device
ListTitle = HD POST: Sys Rec NVRAM CRC
Message   = A problem was detected with the hemodialysis device.\n- Locate the ID code found in the bottom left corner\nof the alarm screen.\n- Call service to report the issue and schedule a repair.

[252]
Title     = Service Required: Hemodialysis Device
ListTitle = HD POST: Serv Rec NVRAM CRC
Message   = A problem was detected with the hemodialysis device.\n- Locate the ID code found in the bottom left corner\nof the alarm screen.\n- Call service to report the issue and schedule a repair.

[253]
Title     = Service Required: Dialysate Device
ListTitle = DG POST: Sys Rec NVRAM CRC
Message   = A problem was detected with the dialysate device.\n- Locate the ID code found in the bottom left corner\nof the alarm screen.\n- Call service to report the issue and schedule a repair.
SRSDG 609 = 

[254]
Title     = Service Required: Dialysate Device
ListTitle = DG POST: Serv Rec NVRAM CRC
Message   = A problem was detected with the dialysate device.\n- Locate the ID code found in the bottom left corner\nof the alarm screen.\n- Call service to report the issue and schedule a repair.
SRSDG 610 = 

[255]
Title     = Service Required: Hemodialysis Device
ListTitle = HD POST: UI Compatibility
Message   = A problem was detected with the hemodialysis device.\n- Locate the ID code found in the bottom left corner\nof the alarm screen.\n- Call service to report the issue and schedule a repair.

[256]
Title     = Chemical Flush in Progress
ListTitle = Cleaning: Chem Flush In Progress
Message   = Chemical flush in progress.\n- Please wait for the process to complete. \n- You will not be able to create a treatment until the process\nis finished.\n- To end this process, press STOP on the front of the device.
 = SRSUI 497

[257]
Title     = Service Required: Hemodialysis Device
ListTitle = HD POST: Institutional Rec NVRAM CRC
Message   = A problem was detected with the hemodialysis device.\n- Locate the ID code found in the bottom left corner\nof the alarm screen.\n- Call service to report the issue and schedule a repair.

[258]
Title     = Service Required: Hemodialysis Device
ListTitle = HD POST: OS Version
Message   = A problem was detected with the hemodialysis device.\n- Locate the ID code found in the bottom left corner\nof the alarm screen.\n- Call service to report the issue and schedule a repair.

[259]
Title     = Service Required: Hemodialysis Device
ListTitle = HD Fault: Temp Sensors Error
Message   = A problem was detected with the hemodialysis device.\n- Treatment must be terminated.\n- Locate the ID code found in the bottom left corner\nof the alarm screen.\n- Call service to report the issue and schedule a repair.

[260]
Title     = Service Required: Hemodialysis Device
ListTitle = HD POST: UI Image
Message   = A problem was detected with the hemodialysis device.\n- Locate the ID code found in the bottom left corner\nof the alarm screen.\n- Call service to report the issue and schedule a repair.
 = SRSUI 1067

[261]
Title     = Service Required: Hemodialysis Device
ListTitle = HD POST: UI CAN Driver
Message   = A problem was detected with the hemodialysis device.\n- Locate the ID code found in the bottom left corner\nof the alarm screen.\n- Call service to report the issue and schedule a repair.
 = SRSUI 1068

[262]
Title     = 
ListTitle = 
Message   = 

[263]
Title     = Service Required: Hemodialysis Device
ListTitle = HD POST: UI Touch Driver
Message   = A problem was detected with the hemodialysis device.\n- Locate the ID code found in the bottom left corner\nof the alarm screen.\n- Call service to report the issue and schedule a repair.
 = SRSUI 1070

[264]
Title     = Service Required: Hemodialysis Device
ListTitle = HD POST: UI SD- Card
Message   = A problem was detected with the hemodialysis device.\n- Locate the ID code found in the bottom left corner\nof the alarm screen.\n- Call service to report the issue and schedule a repair.
 = SRSUI 1071

[265]
Title     = Service Required: Hemodialysis Device
ListTitle = HD POST: UI RTC
Message   = A problem was detected with the hemodialysis device.\n- Locate the ID code found in the bottom left corner\nof the alarm screen.\n- Call service to report the issue and schedule a repair.
 = SRSUI 1072

[266]
Title     = Service Required: Hemodialysis Device
ListTitle = HD POST: UI WiFi
Message   = A problem was detected with the hemodialysis device.\n- Locate the ID code found in the bottom left corner\nof the alarm screen.\n- Call service to report the issue and schedule a repair.
 = SRSUI 1073

[267]
Title     = Service Required: Hemodialysis Device
ListTitle = HD POST: UI Bluetooth
Message   = A problem was detected with the hemodialysis device.\n- Locate the ID code found in the bottom left corner\nof the alarm screen.\n- Call service to report the issue and schedule a repair.
 = SRSUI 1074

[268]
Title     = Service Required: Hemodialysis Device
ListTitle = HD POST: UI Ethernet
Message   = A problem was detected with the hemodialysis device.\n- Locate the ID code found in the bottom left corner\nof the alarm screen.\n- Call service to report the issue and schedule a repair.
 = SRSUI 1075

[269]
Title     = Service Required: Hemodialysis Device
ListTitle = HD POST: UI Sound
Message   = A problem was detected with the hemodialysis device.\n- Locate the ID code found in the bottom left corner\nof the alarm screen.\n- Call service to report the issue and schedule a repair.
 = SRSUI 1076

[270]
Title     = Service Required: Hemodialysis Device
ListTitle = HD POST: Proc Safestate
Message   = A problem was detected with the hemodialysis device.\n- Locate the ID code found in the bottom left corner\nof the alarm screen.\n- Call service to report the issue and schedule a repair.

[271]
Title     = Service Required: Dialysate Device
ListTitle = DG POST: Proc Safestate
Message   = A problem was detected with the dialysate device.\n- Locate the ID code found in the bottom left corner\nof the alarm screen.\n- Call service to report the issue and schedule a repair.
SRSDG 822 = 

[272]
Title     = Service Required: Hemodialysis Device
ListTitle = HD Alarm (Low): Fan Speed
Message   = A non- critical problem was detected with the hemodialysis\n device.\n- Call service to report the issue and schedule a repair.

[273]
Title     = 
ListTitle = 
Message   = 

[274]
Title     = Service Required: Dialysate Device
ListTitle = DG Fault: Reservoir Fault
Message   = A problem was detected with the dialysate device. \n- Treatment must be terminated.\n- Locate the ID code found in the bottom left corner\nof the alarm screen.\n- Call service to report the issue and schedule a repair.

[275]
Title     = Service Required: Hemodialysis Device
ListTitle = HD Fault: Arterial Press Range
Message   = A problem was detected with the hemodialysis device. \n- Treatment must be terminated.\n- Locate the ID code found in the bottom left corner\nof the alarm screen.\n- Call service to report the issue and schedule a repair.

[276]
Title     = Service Required: Hemodialysis Device
ListTitle = HD Fault: Venous Press Range
Message   = A problem was detected with the hemodialysis device. \n- Treatment must be terminated.\n- Locate the ID code found in the bottom left corner\nof the alarm screen.\n- Call service to report the issue and schedule a repair.

[277]
Title     = Service Required: Hemodialysis Device
ListTitle = HD Fault: Occlusion Sens Range
Message   = A problem was detected with the hemodialysis device. \n- Treatment must be terminated.\n- Locate the ID code found in the bottom left corner\nof the alarm screen.\n- Call service to report the issue and schedule a repair.

[278]
Title     = Dialysate Reservoir Error
ListTitle = Dial. Gen: Reservoir Overfill
Message   = A problem has been detected with dialysate generation. \n- Treatment is paused and will need to be resumed when \ndialysate is ready for use.

[279]
Title     = Service Required: Dialysate Device
ListTitle = DG Fault: Reservoir Drain
Message   = A problem was detected with the dialysate device. \n- Treatment must be terminated.\n- Locate the ID code found in the bottom left corner\nof the alarm screen.\n- Call service to report the issue and schedule a repair.
SRSDG 752 = 

[280]
Title     = Service Required: Dialysate Device
ListTitle = DG Fault: DRP Direction Fault
Message   = A problem was detected with the dialysate device. \n- Treatment must be terminated.\n- Locate the ID code found in the bottom left corner\nof the alarm screen.\n- Call service to report the issue and schedule a repair.
SRSDG 888 = 

[281]
Title     = Acid Concentrate Low
ListTitle = Dial. Gen: Acid Conc. Low
Message   = The acid concentrate is low.\n- Replace acid concentrate container.
SRSDG 836 = 

[282]
Title     = Bicarb Concentrate Low
ListTitle = Dial. Gen: Bicarb Conc. Low
Message   = Bicarbonate concentrate is low.\n- Replace the bicarbonate concentrate container.
SRSDG 837 = 

[283]
Title     = Service Required: Dialysate Device
ListTitle = DG Fault: LC Range
Message   = A problem was detected with the dialysate device. \n- Treatment must be terminated.\n- Locate the ID code found in the bottom left corner\nof the alarm screen.\n- Call service to report the issue and schedule a repair.
SRSDG 615 = 

[284]
Title     = Service Required: Dialysate Device
ListTitle = DG Fault: Redundant LC Check
Message   = A problem was detected with the dialysate device. \n- Treatment must be terminated.\n- Locate the ID code found in the bottom left corner\nof the alarm screen.\n- Call service to report the issue and schedule a repair.
SRSDG 383 = 

[285]
Title     = RO Permeate Sample in Progress
ListTitle = Cleaning: RO Permeate Sample In Progress
Message   = RO Permeate Sample is in progress.\n- Please wait for the process to complete. \n- You will not be able to create a treatment until the process\nis finished.\n- To end this process, press STOP on the front of the device.

[286]
Title     = Concentrate Connection Cap Removed
ListTitle = Cleaning: Conc Cap Removed
Message   = The concentrate connection cap was removed from the \ndialysate device during disinfection.\n- Disinfection terminated.\n- Replace cap before attempting disinfection again.

[287]
Title     = Service Required: Hemodialysis Device
ListTitle = HD Fault: Proc- FPGA Clock
Message   = A problem was detected with the hemodialysis device. \n- Treatment must be terminated.\n- Locate the ID code found in the bottom left corner\nof the alarm screen.\n- Call service to report the issue and schedule a repair.

[288]
Title     = Service Required: Dialysate Device
ListTitle = DG Fault: LC Drift Check
Message   = A problem was detected with the dialysate device. \n- Treatment must be terminated.\n- Locate the ID code found in the bottom left corner\nof the alarm screen.\n- Call service to report the issue and schedule a repair.

[289]
Title     = Dialysate Connection Cap Removed
ListTitle = Cleaning: Dialysate Cap Removed
Message   = The dialysate connection cap was removed from the\ndialysate device during disinfection.\n- Disinfection terminated.\n- Replace cap before attempting disinfection again.
SRSDG 928 = 

[290]
Title     = Service Required: Hemodialysis Device
ListTitle = HD Fault: Ven. Pres. Com
Message   = A problem was detected with the hemodialysis device. \n- Treatment must be terminated.\n- Locate the ID code found in the bottom left corner\nof the alarm screen.\n- Call service to report the issue and schedule a repair.

[291]
Title     = Flush In Progress
ListTitle = Cleaning: Flush In Progress
Message   = System flush is in progress\n- Please wait for the process to complete. \n- You will not be able to create a treatment until the process\nis finished.\n- To end this process, press STOP on the front of the device.

[292]
Title     = Heat Disinfection in Progress
ListTitle = Cleaning: Heat Disinf In Progress
Message   = Heat disinfection is in progress.\n- Please wait for the process to complete. \n- You will not be able to create a treatment until the process\nis finished.\n- To end this process, press STOP on the front of the device.

[293]
Title     = Chemical Disinfection in Progress
ListTitle = Cleaning: Chem Disinfect In Progress
Message   = Chemical disinfection in progress.\n- Please wait for the process to complete. \n- You will not be able to create a treatment until the process\nis finished.\n- To end this process, press STOP on the front of the device.

[294]
Title     = Active Cool in Progress
ListTitle = Cleaning: Active Cool In Progress
Message   = Active Cool is in progress.\n- Please wait for the process to complete. \n- You will not be able to create a treatment until the process\nis finished.\n- To end this process, press STOP on the front of the device.

[295]
Title     = Service Required: Hemodialysis Device
ListTitle = HD POST: UI CloudSync
Message   = A problem was detected with the hemodialysis device.\n- Locate the ID code found in the bottom left corner\nof the alarm screen.\n- Call service to report the issue and schedule a repair.
 = SRSUI 1238

[296]
Title     = Service Required: Dialysate Device
ListTitle = DG Fault: TDi RTD Comm
Message   = A problem was detected with the dialysate device. \n- Treatment must be terminated.\n- Locate the ID code found in the bottom left corner\nof the alarm screen.\n- Call service to report the issue and schedule a repair.
SRSDG 951 = 

[297]
Title     = Service Required: Dialysate Device
ListTitle = DG Fault: TRo RTD Comm
Message   = A problem was detected with the dialysate device. \n- Treatment must be terminated.\n- Locate the ID code found in the bottom left corner\nof the alarm screen.\n- Call service to report the issue and schedule a repair.
SRSDG 950 = 

[298]
Title     = Service Required: Dialysate Device
ListTitle = DG Fault: Baro Pres Comm
Message   = A problem was detected with the dialysate device. \n- Treatment must be terminated.\n- Locate the ID code found in the bottom left corner\nof the alarm screen.\n- Call service to report the issue and schedule a repair.
SRSDG 948 = 

[299]
Title     = Service Required: Dialysate Device
ListTitle = DG POST: Serial Number Check
Message   = A problem was detected with the dialysate device.\n- Locate the ID code found in the bottom left corner\nof the alarm screen.\n- Call service to report the issue and schedule a repair.
SRSDG 952 = 

[300]
Title     = Service Required: Hemodialysis Device
ListTitle = HD POST: Serial Number Check
Message   = A problem was detected with the hemodialysis device.\n- Locate the ID code found in the bottom left corner\nof the alarm screen.\n- Call service to report the issue and schedule a repair.

[301]
Title     = Remove Dialysate Cap
ListTitle = Cleaning: RO Permeate Sample Connect Cap
Message   = - Remove the left dialysate cap.\n- Disinfect the bottom dialysate port using a 70% isopropyl\nalcohol wipe and allow to dry completely.\n- Using aseptic technique, connect extension tubing\nto bottom dialysate port.\n- Keep the right concentrate cap on the device.

[302]
Title     = Service Required: Dialysate Device
ListTitle = DG Fault: Processor RAM error
Message   = A problem was detected with the dialysate device. \n- Treatment must be terminated.\n- Locate the ID code found in the bottom left corner\nof the alarm screen.\n- Call service to report the issue and schedule a repair.
SRSDG 126 = 

[303]
Title     = Service Required: Dialysate Device
ListTitle = DG Fault: DRP Hall Commutation
Message   = A problem was detected with the dialysate device. \n- Treatment must be terminated.\n- Locate the ID code found in the bottom left corner\nof the alarm screen.\n- Call service to report the issue and schedule a repair.
SRSDG 958 = 

[304]
Title     = Service Required: Hemodialysis Device
ListTitle = HD POST: Usage Rec NVRAM CRC
Message   = A problem was detected with the hemodialysis device.\n- Locate the ID code found in the bottom left corner\nof the alarm screen.\n- Call service to report the issue and schedule a repair.

[305]
Title     = Service Required: Hemodialysis Device
ListTitle = HD Fault: Processor RAM error
Message   = A problem was detected with the hemodialysis device. \n- Treatment must be terminated.\n- Locate the ID code found in the bottom left corner\nof the alarm screen.\n- Call service to report the issue and schedule a repair.

[306]
Title     = Turn Off Inlet Water Valves
ListTitle = Cleaning: Turn Off Inlet Water Valves
Message   = Heat disinfection is in progress.\n- Turn off inlet water valves.

[307]
Title     = Power Loss
ListTitle = Blood Stop: Loss of AC Power
Message   = Treatment must be terminated due to a power loss.\n- Follow clinic instructions on when to initiate manual rinseback.\n- Check all electrical connections.\n- If power returns within 5 minutes of outage, \n- rinseback will be allowed.

[308]
Title     = Service Required: Dialysate Device
ListTitle = DG Fault: CPi Comm
Message   = A problem was detected with the dialysate device. \n- Treatment must be terminated.\n- Locate the ID code found in the bottom left corner\nof the alarm screen.\n- Call service to report the issue and schedule a repair.
SRSDG 959 = 

[309]
Title     = Service Required: Dialysate Device
ListTitle = DG Fault: CPo Comm
Message   = A problem was detected with the dialysate device. \n- Treatment must be terminated.\n- Locate the ID code found in the bottom left corner\nof the alarm screen.\n- Call service to report the issue and schedule a repair.
SRSDG 960 = 

[310]
Title     = Service Required: Dialysate Device
ListTitle = DG Fault: CD1 Comm
Message   = A problem was detected with the dialysate device. \n- Treatment must be terminated.\n- Locate the ID code found in the bottom left corner\nof the alarm screen.\n- Call service to report the issue and schedule a repair.
SRSDG 962 = 

[311]
Title     = Service Required: Dialysate Device
ListTitle = DG Fault: CD2 Comm
Message   = A problem was detected with the dialysate device. \n- Treatment must be terminated.\n- Locate the ID code found in the bottom left corner\nof the alarm screen.\n- Call service to report the issue and schedule a repair.
SRSDG 961 = 

[312]
Title     = Low Dialysate Flow
ListTitle = Dial. Gen: Dialysate In Flow
Message   = Dialysate flow rate is low. \n- Confirm dialysate concentrate connections are secure. \n- When the flow rates are within target range \nResume/OK button will be available.\n- Press Resume/OK to continue.

[313]
Title     = Disinfection: Water Temperature Low
ListTitle = Cleaning: Inlet Water Temp Low
Message   = Incoming water temperature is too low.\n- Disinfection has been terminated.\n- Check incoming water before initiating disinfection again.
SRSDG 1064
SRSDG 1052
SRSDG 968 = 

[314]
Title     = Disinfection: Water Pressure High
ListTitle = Cleaning: Inlet Water Press High
Message   = Incoming water pressure is too high. \n- Disinfection has been terminated.\n- Check incoming water before initiating disinfection again.
SRSDG 1063
SRSDG 1051
SRSDG 967 = 

[315]
Title     = Disinfection: Water Pressure Low
ListTitle = Cleaning: Inlet Water Press Low
Message   = Incoming water pressure is too low. \n- Disinfection has been terminated.\n- Check incoming water pressure\n   before initiating disinfection again.
SRSDG 1068
SRSDG 1056
SRSDG 966 = 

[316]
Title     = 
ListTitle = 
Message   = 
SRSDG 983 = 

[317]
Title     = 
ListTitle = 
Message   = 
SRSDG 984 = 

[318]
Title     = 
ListTitle = 
Message   = 

[319]
Title     = Residual Chemical Sampling
ListTitle = Cleaning: Chem Residual Sampling
Message   = A water sample is needed to confirm the \nabsence of residual chemical following disinfection.  \n- Test sample according to facility policy. \n- Confirm absence of residual chemical disinfectant.
SRSDG 1040 = 

[320]
Title     = Chemical Residual Timeout
ListTitle = Cleaning: Chem Residual Timeout
Message   = A chemical residual sample was not collected \n- within 30min of chemical flush.\n- To collect a sample for chemical residual,\nyou must repeat the chemical flush.
SRSDG 1043 = 

[321]
Title     = Service Required: Dialysate Device
ListTitle = DG Fault: UVo Error
Message   = A problem was detected with the dialysate device. \n- Treatment must be terminated.\n- Locate the ID code found in the bottom left corner\nof the alarm screen.\n- Call service to report the issue and schedule a repair.
SRSDG 1069 = 

[322]
Title     = Service Required: Hemodialysis Device
ListTitle = HD POST Alarm: UI Invalid Year
Message   = A problem was detected with the hemodialysis device.\n- Locate the ID code found in the bottom left corner\nof the alarm screen.\n- Call service to report the issue and schedule a repair.

[323]
Title     = Service Required: Hemodialysis Device
ListTitle = HD POST Alarm: UI Bad Settings
Message   = A problem was detected with the hemodialysis device.\n- Locate the ID code found in the bottom left corner\nof the alarm screen.\n- Call service to report the issue and schedule a repair.