[0]
Title   = `
Message = 

[1]
Title   = HD POST: Stuck Button
Message = Stop or On button pressed during startup\n-Release button and power cycle\n-Call service to schedule a repair if problem persists

[2]
Title   = HD POST: FPGA Compatibility
Message = Call service to schedule a repair.

[3]
Title   = DG POST: FPGA Compatibility
Message = Call service to schedule a repair.
SRSDG 602
SRSDG 814
SRSDG 1061 = 

[4]
Title   = HD POST: WD Safestate
Message = Call service to schedule a repair.

[5]
Title   = DG POST: WD Safestate
Message = Call service to schedule a repair.
SRSDG 53 = 

[6]
Title   = HD POST: Proc-UI Comm
Message = Call service to schedule a repair.

[7]
Title   = HD Alarm (Low): RTC Bat Low
Message = Call service to schedule a repair.

[8]
Title   = HD POST: Acc Vector
Message = Call service to schedule a repair.

[9]
Title   = DG POST: Acc Vector
Message = Call service to schedule a repair.
SRSDG 323 = 

[10]
Title   = HD POST: BLD Config Emb Mode
Message = Call service to schedule a repair.

[11]
Title   = Dial. Gen: Dialysate Temp Low
Message = Dialysate temperature is low\n- Treatment is paused and will be ready to resume when \ndialysate is within target range.

[12]
Title   = HD POST: HD Image
Message = Call service to schedule a repair.

[13]
Title   = DG POST: DG Image
Message = Call service to schedule a repair.
SRSDG 813 = 

[14]
Title   = DG POST: Usage Rec NVRAM CRC
Message = Call service to schedule a repair.
SRSDG 957 = 

[15]
Title   = Dial. Gen: Dialysate Temp High
Message = Dialysate temperature is high\n-Treatment is paused and will be ready to resume when \ndialysate is within target range.

[16]
Title   = HD POST: Primary Alarm Current
Message = Call service to schedule a repair.

[17]
Title   = HD POST: UI POST Not Complete
Message = Call service to schedule a repair.

[18]
Title   = Loss of DG Comm (DG ACK)
Message = Communication failure with Dialysis Generator.\n-Treatment must be terminated.\n- Ensure all cords are securely connected.

[19]
Title   = Dial. Gen: Dialysate Temp High
Message = Dialysate temperature is high\n- Treatment is paused and will be ready to resume when \ndialysate is within target range.

[20]
Title   = DG POST: Conductivity Cal
Message = Call service to schedule a repair.
SRSDG 16 = 

[21]
Title   = DG POST: Drain Line Vol Cal
Message = Call service to schedule a repair.
SRSDG 936 = 

[22]
Title   = DG POST: Reservoir Vol Cal
Message = Call service to schedule a repair.
SRSDG 935 = 

[23]
Title   = DG POST: Acid Conc Cal
Message = Call service to schedule a repair.
SRSDG 934 = 

[24]
Title   = DG POST: Bicarb Conc Cal
Message = Call service to schedule a repair.
SRSDG 933 = 

[25]
Title   = DG POST: Acc Cal
Message = Call service to schedule a repair.
SRSDG 817 = 

[26]
Title   = HD POST: Acc Cal
Message = Call service to schedule a repair.

[27]
Title   = Process: Pre-Tx Wet Self-Test
Message = Self-test detected has a problem with the blood leak sensor\n- Check cartridge installation on to machine\n- If problem persists, terminate pre-treatment and restart \nwith a new cartridge.

[28]
Title   = DG Fault: Conductivity RTD Comm
Message = Call service to schedule a repair.
SRSDG 864 = 

[29]
Title   = HD POST: SP DAC Cal
Message = Call service to schedule a repair.

[30]
Title   = HD Fault: SW Invalid State
Message = Call service to schedule a repair.

[31]
Title   = HD Fault: BP Current
Message = Call service to schedule a repair.

[32]
Title   = HD Fault: BP Speed
Message = Call service to schedule a repair.

[33]
Title   = HD Fault: BP Direction
Message = Call service to schedule a repair.

[34]
Title   = HD Fault: BP Rotor
Message = Blood pump rotor failure.\n- Check the pump rotor for secure connection.

[35]
Title   = HD Fault: DPi Current
Message = Call service to schedule a repair.

[36]
Title   = HD Fault: DPi Speed
Message = Call service to schedule a repair.

[37]
Title   = HD Fault: DPi Direction
Message = Call service to schedule a repair.

[38]
Title   = HD Fault: DPi Rotor
Message = Dialysate in pump rotor failure.\n- Check the pump rotor for secure connection.

[39]
Title   = HD Fault: DPo Current
Message = Call service to schedule a repair.

[40]
Title   = HD Fault: DPo Speed
Message = Call service to schedule a repair.

[41]
Title   = HD Fault: DPo Direction
Message = Call service to schedule a repair.

[42]
Title   = HD Fault: DPo Rotor
Message = Dialysate out pump rotor failure.\n- Check the pump rotor for secure connection.

[43]
Title   = DG Fault: Iso ADC Comm
Message = Call service to schedule a repair.
SRSDG 954 = 

[44]
Title   = HD Fault: UI Comm
Message = Call service to schedule a repair.

[45]
Title   = HD Fault: CAN CRC Com
Message = Call service to schedule a repair.

[46]
Title   = HD Fault: CAN ACK UI Com
Message = Call service to schedule a repair.

[47]
Title   = 
Message = 

[48]
Title   = HD Fault: UF Rate Tare Err
Message = Call service to schedule a repair.

[49]
Title   = HD Fault: FPGA Com
Message = Call service to schedule a repair.

[50]
Title   = DG Fault: Valve Control
Message = Call service to schedule a repair.
SRSDG 26 = 

[51]
Title   = HD Fault: BP Speed
Message = Call service to schedule a repair.

[52]
Title   = HD Fault: DPi Speed
Message = Call service to schedule a repair.

[53]
Title   = HD Fault: DPo Speed
Message = Call service to schedule a repair.

[54]
Title   = HD Fault: Critical Data Err
Message = Call service to schedule a repair.

[55]
Title   = DG Fault: Critical Data Err
Message = Call service to schedule a repair.
SRSDG 921 = 

[56]
Title   = HD Fault: Acc Com
Message = Call service to schedule a repair.

[57]
Title   = DG Fault: Acc Com
Message = Call service to schedule a repair.
SRSDG 869
SRSDG 870 = 

[58]
Title   = HD Fault: Valve Home
Message = Call service to schedule a repair.

[59]
Title   = HD Fault: Valve Transition Err
Message = Call service to schedule a repair.

[60]
Title   = HD Fault: Valve Control
Message = Call service to schedule a repair.

[61]
Title   = HD Fault: Valve Current
Message = Call service to schedule a repair.

[62]
Title   = HD Fault: Valve Position
Message = Call service to schedule a repair.

[63]
Title   = HD Fault: BLD Com
Message = Call service to schedule a repair.

[64]
Title   = DG Fault: Baro Range
Message = Call service to schedule a repair.
SRSDG 874 = 

[65]
Title   = Loss of DG Comm (Reject)
Message = Communication failure with Dialysis Generator.\n-Treatment must be terminated.\n- Ensure all cords are securely connected.

[66]
Title   = HD POST: BLD Config Set Point
Message = Call service to schedule a repair.

[67]
Title   = Process: Pre-Tx Remove Cartridge
Message = Cartridge has been detected.\n- Open door\n- Remove cartridge\n- Close door\n- Resume

[68]
Title   = Dial. Gen: Dialysate not ready
Message = Dialysate is not yet ready.\n- Treatment is paused and will be ready to resume when \ndialysate is ready for use.

[69]
Title   = HD POST: BLD Cal
Message = Call service to schedule a repair.

[70]
Title   = Process: Pre-Tx Remove Cartridge
Message = Cartridge has been detected.\n- Open door\n- Remove cartridge\n- Close door\n- Resume

[71]
Title   = Process: Pre-Tx Remove Cartridge
Message = Cartridge has been detected.\n- Open door\n- Remove cartridge\n- Close door\n- Resume

[72]
Title   = Loss of DG Comm (LC)
Message = Communication failure with Dialysis Generator.\n-Treatment must be terminated.\n- Ensure all cords are securely connected.

[73]
Title   = Loss of DG Comm (TDI/TRO)
Message = Communication failure with Dialysis Generator.\n-Treatment must be terminated.\n- Ensure all cords are securely connected.

[74]
Title   = DG Fault: UVi On No Flow
Message = Call service to schedule a repair.
SRSDG 600 = 

[75]
Title   = HD Fault: Syringe DAC
Message = Call service to schedule a repair.

[76]
Title   = HD Fault: Voltage Monitor
Message = Call service to schedule a repair.

[77]
Title   = DG Fault: Voltage Monitor
Message = Call service to schedule a repair.
SRSDG 46
SRSDG 866
SRSDG 1088 = 

[78]
Title   = HD Fault: Syringe Pump Enc Dir
Message = Call service to schedule a repair.

[79]
Title   = HD Fault: Syringe Pump Drv Dir
Message = Call service to schedule a repair.

[80]
Title   = HD Fault: Syringe Pump Driver
Message = Call service to schedule a repair.

[81]
Title   = HD Fault: Syringe Pump OT
Message = Call service to schedule a repair.

[82]
Title   = HD Fault: Syringe Pump DAC Err
Message = Call service to schedule a repair.

[83]
Title   = HD Fault: Syringe Pump On Err
Message = Call service to schedule a repair.

[84]
Title   = DG POST: HD RTC Time
Message = Call service to schedule a repair.
SRSDG 815 = 

[85]
Title   = Blood Stop: Cartridge Lever Open
Message = Cartridge Lock Lever is not closed.\n- Open front door and push lever all the way down.\n- Close door and press RESUME button to continue.

[86]
Title   = HD POST: HD RTC Time
Message = Call service to schedule a repair.

[87]
Title   = DG POST: Heat Cal
Message = Call service to schedule a repair.
SRSDG 929 = 

[88]
Title   = DG Fault: CP1 CP2 Speed Range
Message = Call service to schedule a repair.

[89]
Title   = DG Fault: UVo On No Flow
Message = Call service to schedule a repair.
SRSDG 599 = 

[90]
Title   = DG Fault: LC A1/B1 Comm
Message = Call service to schedule a repair.
SRSDG 604 = 

[91]
Title   = Loss of DG Comm (FMD)
Message = Communication failure with Dialysis Generator.\n-Treatment must be terminated.\n- Ensure all cords are securely connected.

[92]
Title   = 
Message = 

[93]
Title   = DG Fault: RO Permeate Cond High
Message = Call service to schedule a repair.
SRSDG 430 = 

[94]
Title   = DG Fault: Pressure Sensor Range
Message = Call service to schedule a repair.
SRSDG 629 = 

[95]
Title   = DG Fault: WD Error
Message = Call service to schedule a repair.
SRSDG 907 = 

[96]
Title   = Dial. Gen: Inlet Water Temp High
Message = Inlet water temperature is high.\n- Treatment is paused\n- Check the incoming water supply.
SRSDG 410 = 

[97]
Title   = Dial. Gen: Dialysate Cond.
Message = Dialysate conductivity is out of range.\n- Check acid and bicarb concentrate is correct and not empty.
SRSDG 397 = 

[98]
Title   = HD Alarm (Low): Battery Com
Message = Call service to schedule a repair.

[99]
Title   = HD Fault: Syringe Pump Stall
Message = Call service to schedule a repair.

[100]
Title   = HD Fault: Timeout No Cart ST
Message = Call service to schedule a repair.

[101]
Title   = HD POST: UI-Proc Comm
Message = Call service to schedule a repair.

[102]
Title   = Cleaning: Tpo THD Temp Delta
Message = Cleaning mode process terminated unexpectedly.\n-Restart cleaning mode.\n-If problem persists, call service to schedule a repair.
SRSDG 856
SRSDG 930 = 

[103]
Title   = HD POST: Cal NVRAM CRC
Message = Call service to schedule a repair.

[104]
Title   = HD Fault: Air Trap Sensor
Message = Call service to schedule a repair.

[105]
Title   = DG POST: Cal NVRAM CRC
Message = Call service to schedule a repair.
SRSDG 608 = 

[106]
Title   = DG POST: Flow Sensor Cal
Message = Call service to schedule a repair.
SRSDG 820
SRSDG 821
SRSDG 1087 = 

[107]
Title   = DG Fault: DG Restarted
Message = Call service to schedule a repair.

[108]
Title   = HD Fault: Syringe Pump ADC Com
Message = Call service to schedule a repair.

[109]
Title   = HD Fault: Syringe Pump Vol
Message = Call service to schedule a repair.

[110]
Title   = HD Fault: Syringe Pump Speed
Message = Call service to schedule a repair.

[111]
Title   = HD Fault: Syringe Pump Speed
Message = Call service to schedule a repair.

[112]
Title   = DG Fault: LC A2/B2 Comm
Message = Call service to schedule a repair.
SRSDG 953 = 

[113]
Title   = DG Fault: DRP Current
Message = Call service to schedule a repair.
SRSDG 890 = 

[114]
Title   = Process: Pre-Tx Wet Self-Test
Message = Self-test has detected a problem with the air bubble sensor\n- Check cartridge installation on to machine\n- If problem persists, terminate pre-treatment and \nrestart with a new cartridge.

[115]
Title   = DG Fault: Temp Sensor Range
Message = Call service to schedule a repair.
SRSDG 224 = 

[116]
Title   = HD Alarm (Low): SD-Card Error
Message = SD-Card Failure \n- Power cycle the system.\n- Call service to schedule a repair if problem persists.

[117]
Title   = Loss of HD Comm (HD ACK)
Message = Communication failure with Dialysis Generator.\n-Treatment must be terminated.\n- Ensure all cords are securely connected.
SRSDG 909 = 

[118]
Title   = DG Fault: RTC Config
Message = Call service to schedule a repair.
SRSDG 43 = 

[119]
Title   = DG Alarm (Low): RTC Bat Low
Message = Call service to schedule a repair.
SRSDG 908 = 

[120]
Title   = Process: Pre-Tx Wet Self-Test
Message = Self-test has detected a bubble in the venous bubble detector\n- The cartridge should be primed\n- Check cartridge installation on to machine\n- If problem persists, terminate pre-treatment and \nrestart with a new cartridge.

[121]
Title   = DG Fault: Prim Heater Lg Control
Message = Call service to schedule a repair.
SRSDG 611 = 

[122]
Title   = DG Fault: Prim Heater Sm Control
Message = Call service to schedule a repair.
SRSDG 612 = 

[123]
Title   = DG Fault: Trimmer Heater Control
Message = Call service to schedule a repair.
SRSDG 613 = 

[124]
Title   = Blood Stop: Blood Clot Risk
Message = Blood pump has been off for too long.\n-  Treatment must be terminated. Blood clot risk.\n- NO RINSEBACK ALLOWED.

[125]
Title   = Blood Stop: Blood Clot Risk
Message = Blood pump has been off for too long.\n-  Treatment must be terminated. Blood clot risk.\n- NO RINSEBACK ALLOWED.

[126]
Title   = Blood Stop: Dialyzer Blood Leak
Message = A blood leak has been detected. Treatment must end.

[127]
Title   = Blood Stop: Venous Pres. Low
Message = Venous pressure is low.\n- Check to be sure your blue venous connections are secure.\n- Check that your venous access is connected and secured \nproperly.

[128]
Title   = Blood Stop: Venous Air Bubble
Message = Venous air bubble detected indicating failure of air trap \ncontrol system.\n- Treatment must be terminated without option for rinseback.\n- Check access for dislodgement.

[129]
Title   = 
Message = 

[130]
Title   = Blood Stop: Venous Pres. High
Message = Venous pressure is high.\n- Check for access or patient discomfort.\n- Resolve access issue if applicable.\n- Check that there are no kinks or clots in the tubing.\n- Unkink the lines if applicable.\n- End treatment and do not return blood if clots are present.

[131]
Title   = Blood Stop: Arterial Pres. Low
Message = Arterial pressure is low.\n- Check that the access is properly connected and secured.\n- Resolve access issue if applicable.\n- Check to be sure the red arterial connections are secure.\n- Check that there are no kinks or clots in the tubing.\n- Unkink lines if applicable.\n- End treatment and do not return blood if clots are present.

[132]
Title   = Blood Stop: Arterial Pres. High
Message = Arterial pressure is high.\n- Check that the access is properly connected and secured.\n- Resolve access issue if applicable.\n- Check to be sure your red arterial connections are secure.\n- Check that there are no kinks or clots in the tubing.\n- Unkink lines if applicable.\n- End treatment and do not return blood if clots are present.

[133]
Title   = DG Fault: Fluid Leak in DG
Message = Fluid leak detected in Dialysate Generation Delivery Device.\n-Treatment must be terminated.\n- Shut off water source and disconnect water and \nelectrical connections from system.\n- Call service to schedule a repair.
SRSDG 328 = 

[134]
Title   = Blood Stop: Fluid Leak in HD
Message = Fluid leak detected in Hemodialysis Delivery device.\n- If in treatment, BLOOD STOPPED.\n-Identify and correct the cause of the spill.\n- Clean up the spill and dry leak sensor.\n- If in treatment, resume treatment.

[135]
Title   = Blood Stop: HD Shock Detected
Message = Excessive movement detected with Hemodialysis Delivery \ndevice.\n- Confirm the device is stationary and level before continuing.

[136]
Title   = Dial. Gen: Shock-Vibration
Message = Excessive movement detected with Dialysis Generation \ndevice.\n- Treatment is paused.\n- Confirm the device is stationary and level before continuing.
SRSDG 327 = 

[137]
Title   = Blood Stop: HD Tilted
Message = Excessive tilt detected with Hemodialysis Delivery device.\n- Confirm the device is stationary and level before continuing.

[138]
Title   = Dial. Gen: Tilt
Message = Excessive tilt detected with Dialysis Generation device.\n- Treatment is paused.\n-Confirm the device is stationary and level before continuing.
SRSDG 326 = 

[139]
Title   = Loss of AC Power
Message = Power has been lost. Check all electrical connections.\n- The display and CPU will run off of the battery until \npower returns.

[140]
Title   = Loss of DG Comm (Timeout)
Message = Communication failure with Dialysis Generator.\n-Treatment must be terminated.\n- Ensure all cords are securely connected.

[141]
Title   = Blood Stop: Air Trap Fill
Message = Failure to fill the Air Trap.\n- Treatment must be terminated without option for rinseback.\n- Check access for dislodgement.

[142]
Title   = Blood Stop: Blood Pump Occlusion
Message = Occlusion detected after the blood pump.\n- Check for clots or kinks around the dialyzer and in the \nvenous line.\n- Resolve access issue if applicable.\n- End treatment and do not return blood if clots are present.\n- Check for access or patient discomfort.\n- Unkink the lines if applicable.

[143]
Title   = DG Fault: TRo TDi Delta
Message = Call service to schedule a repair.
SRSDG 912 = 

[144]
Title   = Cleaning: Inlet Water Cond High
Message = Cleaning Mode Inlet water conductivity too high.\n- Cleaning mode process has terminated \n- Check inlet water before restarting cleaning mode.
SRSDG 1066
SRSDG 1054
SRSDG 970 = 

[145]
Title   = Dial. Gen: Acid Conc. Cond.
Message = Acid concentrate conductivity during prime is out of range.\n- Check correct acid concentrate is connected and full.\n- Resume to reprime concentrate.
SRSDG 846 = 

[146]
Title   = DG POST: DG RTC Timer
Message = Call service to schedule a repair.
SRSDG 312 = 

[147]
Title   = Dial. Gen: Dialysate not ready
Message = Dialysate is not yet ready.\n- Treatment is paused and will be ready to resume when \ndialysate is ready for use.
SRSDG 398 = 

[148]
Title   = Cleaning: Inlet Water Temp High
Message = Cleaning Mode Inlet water temperature too high.\n- Cleaning mode process has terminated.\n- Check inlet water before restarting cleaning mode.
SRSDG 1065
SRSDG 1053
SRSDG 969 = 

[149]
Title   = HD Fault: WD Error
Message = Call service to schedule a repair.

[150]
Title   = Dial. Gen: Inlet Water Cond High
Message = Inlet water conductivity is high.\n- Treatment is paused.\n- Check the incoming water supply.
SRSDG 391 = 

[151]
Title   = Dial. Gen: Inlet Water Cond Low
Message = Inlet water conductivity is low.\n- Treatment is paused.\n- Check the incoming water supply.
SRSDG 826 = 

[152]
Title   = Dial. Gen: Inlet Water Pres Low
Message = Inlet water pressure is low.\n- Treatment is paused.\n- Check the incoming water supply.
SRSDG 417 = 

[153]
Title   = Process: Pre-Tx Terminated
Message = Pre-Treatment timeout.\n- Patient was not connected to device\n- Pre-Treatment has been terminated\n- Proceed to end treatment to remove cartridge from system.

[154]
Title   = Cleaning: Inlet Water Cond Low
Message = Cleaning Mode Inlet water conductivity too low.\n- Cleaning mode process has terminated \n- Check inlet water before restarting cleaning mode.
SRSDG 1067
SRSDG 1055
SRSDG 971 = 

[155]
Title   = Loss of DG Comm (Reservoir)
Message = Communication failure with Dialysis Generator.\n-Treatment must be terminated.\n- Ensure all cords are securely connected.

[156]
Title   = Loss of DG Comm (Op Mode)
Message = Communication failure with Dialysis Generator.\n-Treatment must be terminated.\n- Ensure all cords are securely connected.

[157]
Title   = Cleaning: Chem Disinf PAA Prime
Message = Unable to sense proper chemical disinfectant.\n- Cleaning mode process has terminated.\n- Check that proper chemical disinfectant is connected to the \nbicarb port.\n- Check chemical disinfectant bottle is not empty.
SRSDG 988 = 

[158]
Title   = Dial. Gen: Inlet Water Temp Low
Message = Inlet water temperature is low.\n- Treatment is paused.\n- Check the incoming water supply.
SRSDG 408 = 

[159]
Title   = Cleaning: Chem Disinf Connect Cap
Message = Remove chemical disinfectant connection and close cap.
SRSDG 1044 = 

[160]
Title   = HD Fault: BP Rotor Max Speed
Message = Call service to schedule a repair.

[161]
Title   = DG Fault: HD-DG Comm
Message = Call service to schedule a repair.
SRSDG 122 = 

[162]
Title   = DG Fault: Proc-FPGA Clock
Message = Call service to schedule a repair.
SRSDG 867 = 

[163]
Title   = Dial. Gen: UF Rate Check
Message = Ultrafiltration control detected and incorrect rate.\n- This can be caused by excessive movement of system\n(shock/vibration)\n- Check system is stable and level\n- Resume and If problem persists, call service to schedule a\nrepair.

[164]
Title   = Dial. Gen: UF Rate Check
Message = Ultrafiltration control detected and incorrect rate.\n- This can be caused by excessive movement of system \n(shock/vibration).\n- Check system is stable and level\n- Resume and If problem persists, call service to schedule a \nrepair.

[165]
Title   = Blood Stop: Blood Clot Risk
Message = Blood pump has been off for too long.\n-  Treament must be terminated.  Blood clot risk.\n- NO RINSEBACK ALLOWED.

[166]
Title   = 
Message = 

[167]
Title   = Blood Stop: Door Open
Message = Device door is open.\n - Close door and press RESUME button to continue.

[168]
Title   = 
Message = 

[169]
Title   = DG Fault: Dialysate Flow Sens Rg
Message = Call service to schedule a repair.
SRSDG 643 = 

[170]
Title   = Heparin Syringe Empty
Message = Heparin syringe empty.\n- Treatment will continue\n- If additional heparin is required to complete treatment, \nadminister manually.

[171]
Title   = Process: Pre-Tx Hep. Pump Occ.
Message = Heparin pump occlusion detected.\n- Check heparin line is unclamped.\n- Check there are no kinks in the heparin line.

[172]
Title   = Process: Pre-Tx Not Enough Hep.
Message = Not enough heparin is available for treatment.\n- Check if syringe pump is touching syringe plunger.\n- If syringe pump is touching syringe plunger, end treatment.\n- If syringe pump is not touching syringe plunger, reload \nsyringe with enough heparin.

[173]
Title   = HD Fault: RTC Config
Message = Call service to schedule a repair.

[174]
Title   = HD POST: HD RTC Timer
Message = Call service to schedule a repair.

[175]
Title   = HD Fault: Pump Commutation Err
Message = Call service to schedule a repair.

[176]
Title   = 
Message = 

[177]
Title   = DG Fault: Software Invalid State
Message = Call service to schedule a repair.
SRSDG 919 = 

[178]
Title   = HD Fault: UI-Proc Comm
Message = Call service to schedule a repair.
 = SRSUI 1066

[179]
Title   = DG Fault: FPGA Com
Message = Call service to schedule a repair.
SRSDG 605 = 

[180]
Title   = DG Fault: RO Flow Sensor Range
Message = Call service to schedule a repair.
SRSDG 883 = 

[181]
Title   = DG Fault: Tare Out of Range
Message = Call service to schedule a repair.
SRSDG 849
SRSDG 838 = 

[182]
Title   = DG POST: LC Cal
Message = Call service to schedule a repair.
SRSDG 162 = 

[183]
Title   = Cleaning: Invalid Resv Transfer
Message = Cleaning mode process terminated unexpectedly.\n-Restart cleaning mode.\n-If problem persists, call service to schedule a repair.
SRSDG 851 = 

[184]
Title   = DG Fault: UVi Error
Message = Call service to schedule a repair.
SRSDG 559 = 

[185]
Title   = DG Alarm (Low): Fan Speed
Message = Fan failure.\n- Check that the fans inlets are not blocked or obstructed.
SRSDG 628 = 

[186]
Title   = DG Fault: CP1/CP2 Fault
Message = Call service to schedule a repair.
SRSDG 891 = 

[187]
Title   = DG Fault: CP1 Speed Fault
Message = Call service to schedule a repair.
SRSDG 905 = 

[188]
Title   = DG Fault: CP2 Speed Fault
Message = Call service to schedule a repair.
SRSDG 906 = 

[189]
Title   = DG Fault: DRP Speed Fault
Message = Call service to schedule a repair.
SRSDG 448 = 

[190]
Title   = DG Fault: DRP Speed Not Off
Message = Call service to schedule a repair.

[191]
Title   = DG Fault: RO Flow High
Message = Call service to schedule a repair.
SRSDG 885 = 

[192]
Title   = DG Fault: RO Flow Low
Message = Call service to schedule a repair.
SRSDG 945 = 

[193]
Title   = 
Message = 

[194]
Title   = DG Fault: RO Driver Feedback
Message = Call service to schedule a repair.
SRSDG 881 = 

[195]
Title   = DG Fault: RO Pump High Pressure
Message = Call service to schedule a repair.
SRSDG 925 = 

[196]
Title   = DG Fault: CPi/CPo Comm
Message = Call service to schedule a repair.
SRSDG 955 = 

[197]
Title   = DG Fault: CD1/CD2 Comm
Message = Call service to schedule a repair.
SRSDG 956 = 

[198]
Title   = DG Fault: HP On With No Flow
Message = Call service to schedule a repair.
SRSDG 872 = 

[199]
Title   = DG Fault: HR On With No Flow
Message = Call service to schedule a repair.
SRSDG 871 = 

[200]
Title   = DG Fault: Thermistor Range
Message = Call service to schedule a repair.
SRSDG 178 = 

[201]
Title   = Process: Pre-Tx Wet Self-Test
Message = Self-test has detected a problem in the dialysate flow \nmeasurement or there is a leak in the dialysate in/out lines.\n- The cartridge should be primed\n- Check cartridge installation on to machine\n- If problem persists, terminate pre-treatment and restart \nwith a new cartridge.

[202]
Title   = Process: Pre-Tx Dry Self-Test
Message = Self-test has detected blood circuit pressure cannot be \nrelieved.\n- Check PBo connection to HD for kinks\n -Check PBo transducer protector for occlusion\n- If problem persists, install a new cartridge and \nPBo transducer protector.

[203]
Title   = 
Message = 

[204]
Title   = DG Fault: RO Rejection
Message = Call service to schedule a repair.
SRSDG 429 = 

[205]
Title   = DG Fault: Cond Sensors Error
Message = Call service to schedule a repair.
SRSDG 913 = 

[206]
Title   = DG Fault: Reservoir Fill Timeout
Message = Call service to schedule a repair.
SRSDG 437 = 

[207]
Title   = DG Fault: FMP Flow Rate Error
Message = Call service to schedule a repair.
SRSDG 240 = 

[208]
Title   = Blood Stop: Venous Pres. High
Message = Venous pressure is high.\n- Check for access or patient discomfort.\n- Resolve access issue if applicable.\n- Check that there are no kinks or clots in the tubing.\n- Unkink the lines if applicable.\n- End treatment and do not return blood if clots are present.

[209]
Title   = Cleaning: Flush Circ Error
Message = Cleaning mode process terminated unexpectedly.\n-Restart cleaning mode.\n-If problem persists, call service to schedule a repair.
SRSDG 980 = 

[210]
Title   = HD Alarm (Low): Battery Fault
Message = Call service to schedule a repair.

[211]
Title   = Blood Stopped:  Warning
Message = Blood pump is stopped.\n- Resume treatment before countdown timer expires.

[212]
Title   = Blood Stopped:  Warning
Message = Blood pump is stopped.\n- Resume treatment before countdown timer expires.

[213]
Title   = Process: Pre-Tx Prime Complete
Message = Prime of the cartridge is complete.\n- Proceed to connect to patient.

[214]
Title   = 
Message = 

[215]
Title   = 
Message = 

[216]
Title   = Process: End of Dialysis Tx
Message = Dialysis Treatment has completed\n- Proceed to end treatment and rinseback.

[217]
Title   = 
Message = 

[218]
Title   = Process: Remove Syringe
Message = Syringe not removed from machine.\n- Remove heparin syringe.

[219]
Title   = Blood Stop: Syringe Not Detected
Message = Heparin is needed for treatment but syringe has been removed \nfrom syringe pump.\n- Install Heparin syringe.

[220]
Title   = DG Fault: THD RTD Comm
Message = Call service to schedule a repair.
SRSDG 947 = 

[221]
Title   = Blood Stop: Saline Bag Empty
Message = Saline bag appears empty.\n- Check saline bag and line and replace if saline bag is \nempty.

[222]
Title   = HD Fault: BP Occ Com
Message = Call service to schedule a repair.

[223]
Title   = HD Fault: Art. Pres. Com
Message = Call service to schedule a repair.

[224]
Title   = Blood Stopped: Treatment Pause
Message = Treatment paused by user.

[225]
Title   = Process: End of Treatment
Message = Dialysis Treatment has completed\n- Proceed to end treatment and rinseback.

[226]
Title   = Process: Pre-Tx Priming Complete
Message = Prime of the cartridge is complete.\n- Proceed to connect to patient.

[227]
Title   = 
Message = 

[228]
Title   = Process: Pre-Tx Prime Timeout
Message = Blood line prime with saline timeout.\n- Check blood and dialysate lines for clamps, kinks or leaks.

[229]
Title   = Process: Pre-Tx Prime Timeout
Message = Dialyzer prime timeout.\n- Check blood and dialysate lines for clamps, kinks or leaks.

[230]
Title   = Process: Pre-Tx Prime Timeout
Message = Dialyzer prime timeout.\n- Check blood and dialysate lines for clamps, kinks or leaks.

[231]
Title   = Process: Pre-Tx Dry Self-Test
Message = Self-test has detected a leak in the circuit\n- Check blood line connections\n- Check dialysate line connections\n- Check PBo and PBa transducer protectors for occlusion.\n- Check clamps.\n- If problem persists, install a new cartridge.

[232]
Title   = Process: Pre-Tx Wet Self-Test
Message = Self-test has detected a problem in the load cell \nmeasurement or there is a leak in the dialysate in/out lines\n- The cartridge should be primed\n- Check cartridge installation onto machine\n- If problem persists, terminate pre-treatment and restart \nwith a new cartridge.

[233]
Title   = DG Fault: Baro Cal CRC
Message = Call service to schedule a repair.
SRSDG 964
SRSDG 949
SRSDG 1089 = 

[234]
Title   = Dial. Gen: Inlet Water Pres High
Message = Inlet water pressure is high.\n- Treatment is paused\n- Check the incoming water supply.
SRSDG 1037 = 

[235]
Title   = Process: Rinseback Complete
Message = Rinseback has been completed.

[236]
Title   = Process: Pre-Tx Dry Self-Test
Message = Self-test has detected fluid in the cartridge.\n- Cartridges are single-use only\n- Install new cartridge to resume.

[237]
Title   = Process: Pre-Tx Prime Timeout
Message = Dialyzer prime timeout.\n- Check blood and dialysate lines for clamps, kinks or leaks.

[238]
Title   = Process: Pre-Tx Dry Self-Test
Message = Self-test has detected cartridge is not installed.\n- Check that a cartridge is properly installed.

[239]
Title   = Process: Post-Tx Remove Cartridge
Message = Cartridge not unloaded, or unloaded improperly.\n- Check that the cartridge has been removed.

[240]
Title   = Dial. Gen: Bicarb Conc. Cond.
Message = Bicarbonate conductivity during prime is out of range.\n- Check correct concentrate is connected and full.\n- Resume to reprime concentrate.
SRSDG 482 = 

[241]
Title   = Cleaning: Resv Drain Timeout
Message = Cleaning mode process terminated unexpectedly.\n-Restart cleaning mode.\n-If problem persists, call service to schedule a repair.
SRSDG 848
SRSDG 90
SRSDG 561
SRSDG 577
SRSDG 590
SRSDG 591
SRSDG 336
SRSDG 879
SRSDG 340
SRSDG 496
SRSDG 501
SRSDG 505
SRSDG 532
SRSDG 535
SRSDG 556
SRSDG 557
SRSDG 1048
SRSDG 1049
SRSDG 651
SRSDG 655
SRSDG 744
SRSDG 745
SRSDG 1004
SRSDG 1008
SRSDG 1019
SRSDG 1023
SRSDG 1033
SRSDG 1034 = 

[242]
Title   = Cleaning: Resv Fill Timeout
Message = Cleaning mode process terminated unexpectedly.\n-Restart cleaning mode.\n-If problem persists, call service to schedule a repair.
SRSDG 850
SRSDG 573
SRSDG 574
SRSDG 579
SRSDG 580
SRSDG 492
SRSDG 493
SRSDG 498
SRSDG 499
SRSDG 508
SRSDG 509
SRSDG 519
SRSDG 690
SRSDG 691
SRSDG 703
SRSDG 711
SRSDG 1020
SRSDG 1024 = 

[243]
Title   = Cleaning: Fluid Loss Detected
Message = Cleaning mode process terminated unexpectedly.\n-Restart cleaning mode.\n-If problem persists, call service to schedule a repair.
SRSDG 853 = 

[244]
Title   = Cleaning: Temp Sensor Check
Message = Cleaning mode process terminated unexpectedly.\n-Restart cleaning mode.\n-If problem persists, call service to schedule a repair.
SRSDG 852 = 

[245]
Title   = Cleaning: Heat Disinfect Temp TO
Message = Cleaning mode process terminated unexpectedly.\n-Restart cleaning mode.\n-If problem persists, call service to schedule a repair.
SRSDG 854 = 

[246]
Title   = Cleaning: RO Water Cond Error
Message = Cleaning mode process terminated unexpectedly.\n-Restart cleaning mode.\n-If problem persists, call service to schedule a repair.

[247]
Title   = 
Message = 

[248]
Title   = Cleaning: Chem Disinfect Proc
Message = Cleaning mode process terminated unexpectedly.\n-Restart cleaning mode.\n-If problem persists, call service to schedule a repair.

[249]
Title   = Cleaning: Chem Disinf PAA Cond
Message = Unable to sense proper chemical disinfectant.\n- Cleaning mode process has terminated.\n- Check that proper chemical disinfectant is connected to the \nbicarb port.\n- Check chemical disinfectant bottle is not empty.
SRSDG 992 = 

[250]
Title   = Cleaning: Chem Disinf Connect PAA
Message = Connect chemical disinfectant bottle to bicarb port.
SRSDG 1046 = 

[251]
Title   = HD POST: Sys Rec NVRAM CRC
Message = Call service to schedule a repair.

[252]
Title   = HD POST: Serv Rec NVRAM CRC
Message = Call service to schedule a repair.

[253]
Title   = DG POST: Sys Rec NVRAM CRC
Message = Call service to schedule a repair.
SRSDG 609 = 

[254]
Title   = DG POST: Serv Rec NVRAM CRC
Message = Call service to schedule a repair.
SRSDG 610 = 

[255]
Title   = HD POST: UI Compatibility
Message = Call service to schedule a repair.

[256]
Title   = Cleaning: Chem Flush In Progress
Message = Chemical disinfect flush in progress\n- Please wait for the process to complete\n- Treatment will not be able to be started until process \ncompletes.\n- Process may be terminated by pressing the HD stop button.
 = SRSUI 497

[257]
Title   = 
Message = 

[258]
Title   = 
Message = 

[259]
Title   = HD Fault: Temp Sensors Error
Message = Call service to schedule a repair.

[260]
Title   = HD POST: UI Image
Message = Call service to schedule a repair.
 = SRSUI 1067

[261]
Title   = HD POST: UI CAN Driver
Message = Call service to schedule a repair.
 = SRSUI 1068

[262]
Title   = HD POST: UI Disp Driver
Message = Call service to schedule a repair.
 = SRSUI 1069

[263]
Title   = HD POST: UI Touch Driver
Message = Call service to schedule a repair.
 = SRSUI 1070

[264]
Title   = HD POST: UI SD-Card
Message = SD-Card Failure \n- Power cycle the system.\n- Call service to schedule a repair if problem persists.
 = SRSUI 1071

[265]
Title   = HD POST: UI RTC
Message = Call service to schedule a repair.
 = SRSUI 1072

[266]
Title   = HD POST: UI WiFi
Message = Call service to schedule a repair.
 = SRSUI 1073

[267]
Title   = HD POST: UI Bluetooth
Message = Call service to schedule a repair.
 = SRSUI 1074

[268]
Title   = HD POST: UI Ethernet
Message = Call service to schedule a repair.
 = SRSUI 1075

[269]
Title   = HD POST: UI Sound
Message = Call service to schedule a repair.
 = SRSUI 1076

[270]
Title   = HD POST: Proc Safestate
Message = Call service to schedule a repair.

[271]
Title   = DG POST: Proc Safestate
Message = Call service to schedule a repair.
SRSDG 822 = 

[272]
Title   = HD Alarm (Low): Fan Speed
Message = Fan failure.\n- Check that the fans inlets are not blocked or obstructed.

[273]
Title   = 
Message = 

[274]
Title   = 
Message = 

[275]
Title   = HD Fault: Arterial Press Range
Message = Call service to schedule a repair.

[276]
Title   = HD Fault: Venous Press Range
Message = Call service to schedule a repair.

[277]
Title   = HD Fault: Occlusion Sens Range
Message = Call service to schedule a repair.

[278]
Title   = DG Fault: Reservoir Overfill
Message = Call service to schedule a repair.

[279]
Title   = DG Fault: Reservoir Drain
Message = Call service to schedule a repair.
SRSDG 752 = 

[280]
Title   = DG Fault: DRP Direction Fault
Message = Call service to schedule a repair.
SRSDG 888 = 

[281]
Title   = Dial. Gen: Acid Conc. Low
Message = Acid concentrate low.\n- Replace acid concentrate bottle.
SRSDG 836 = 

[282]
Title   = Dial. Gen: Bicarb Conc. Low
Message = Bicarbonate concentrate low.\n- Replace bicarbonate concentrate bottle.
SRSDG 837 = 

[283]
Title   = DG Fault: LC Range
Message = Call service to schedule a repair.
SRSDG 615 = 

[284]
Title   = DG Fault: Redundant LC Check
Message = Call service to schedule a repair.
SRSDG 383 = 

[285]
Title   = 
Message = 

[286]
Title   = Cleaning: Conc Cap Removed
Message = Concentrate cap removed from DG during cleaning.\n- Cleaning Process Terminated.

[287]
Title   = HD Fault: Proc-FPGA Clock
Message = Call service to schedule a repair.

[288]
Title   = DG Fault: LC Drift Check
Message = Call service to schedule a repair.

[289]
Title   = Cleaning: Dialysate Cap Removed
Message = Dialysate cap removed from DG during cleaning.\n- Cleaning Process Terminated.
SRSDG 928 = 

[290]
Title   = HD Fault: Ven. Pres. Com
Message = Call service to schedule a repair.

[291]
Title   = Cleaning: Flush In Progress
Message = System flush in progress\n- Please wait for the process to complete.\n- Treatment will not be able to be started until process \ncompletes.\n- Process may be terminated by pressing the HD stop button.

[292]
Title   = Cleaning: Heat Disinf In Progress
Message = Heat disinfect in progress\n- Please wait for the process to complete.\n- Treatment will not be able to be started until process \ncompletes.\n- Process may be terminated by pressing the HD stop button.

[293]
Title   = Cleaning: Chem Disinf In Progress
Message = Chemical disinfect in progress\n- Please wait for the process to complete.\n- Treatment will not be able to be started until process \ncompletes.\n- Process may be terminated by pressing the HD stop button.

[294]
Title   = 
Message = 

[295]
Title   = HD POST: UI CloudSync
Message = Call service to schedule a repair.
 = SRSUI 1238

[296]
Title   = DG Fault: TDi RTD Comm
Message = Call service to schedule a repair.
SRSDG 951 = 

[297]
Title   = DG Fault: TRo RTD Comm
Message = Call service to schedule a repair.
SRSDG 950 = 

[298]
Title   = DG Fault: Baro Pres Comm
Message = Call service to schedule a repair.
SRSDG 948 = 

[299]
Title   = DG POST: Serial Number Check
Message = Call service to schedule a repair.
SRSDG 952 = 

[300]
Title   = HD POST: Serial Number Check
Message = Call service to schedule a repair.

[301]
Title   = 
Message = 

[302]
Title   = DG Fault: Processor RAM error
Message = Call service to schedule a repair.
SRSDG 126 = 

[303]
Title   = DG Fault: DRP Hall Commutation
Message = Call service to schedule a repair.
SRSDG 958 = 

[304]
Title   = HD POST: Usage Rec NVRAM CRC
Message = Call service to schedule a repair.

[305]
Title   = HD Fault: Processor RAM error
Message = Call service to schedule a repair.

[306]
Title   = DG Fault: CD1 CD2 Check
Message = Call service to schedule a repair.

[307]
Title   = Blood Stop: Loss of AC Power
Message = HD power has been lost. \n- Treatment must be terminated.\n-Check all electrical connections.\n- The display and CPU will run off of the battery until \npower returns.\n-If power is returned prior to blood stopped countdown elapses, \nrinseback will be allowed.

[308]
Title   = DG Fault: CPi Comm
Message = Call service to schedule a repair.
SRSDG 959 = 

[309]
Title   = DG Fault: CPo Comm
Message = Call service to schedule a repair.
SRSDG 960 = 

[310]
Title   = DG Fault: CD1 Comm
Message = Call service to schedule a repair.
SRSDG 962 = 

[311]
Title   = DG Fault: CD2 Comm
Message = Call service to schedule a repair.
SRSDG 961 = 

[312]
Title   = Dial. Gen: Dialysate In Flow
Message = Dialysate in flow rate is low\n- Check dialysate line connection to the DG.

[313]
Title   = Cleaning: Inlet Water Temp Low
Message = Cleaning Mode Inlet water temperature too low.\n- Cleaning mode process has terminated.\n- Check inlet water before restarting cleaning mode.
SRSDG 1064
SRSDG 1052
SRSDG 968 = 

[314]
Title   = Cleaning: Inlet Water Press High
Message = Cleaning Mode Inlet water pressure too high.\n- Cleaning mode process has terminated.\n- Check inlet water before restarting cleaning mode.
SRSDG 1063
SRSDG 1051
SRSDG 967 = 

[315]
Title   = Cleaning: Inlet Water Press Low
Message = Cleaning Mode Inlet water pressure too low.\n- Cleaning mode process has terminated.\n- Check inlet water before restarting cleaning mode.
SRSDG 1068
SRSDG 1056
SRSDG 966 = 

[316]
Title   = DG Fault: Acid CP Pump Park
Message = Call service to schedule a repair.
SRSDG 983 = 

[317]
Title   = DG Fault: Bicarb CP Pump Park
Message = Call service to schedule a repair.
SRSDG 984 = 

[318]
Title   = HD Fault: Air Pump Timeout
Message = Unable to reduce fluid level.\n- Air trap may be overfilled.\n- Pressure transducer protector may be contaminated.\n- Treatment must be terminated without option for rinseback.\n- Call service to schedule a repair.

[319]
Title   = Cleaning: Chem Residual Sampling
Message = Collect chemical residuals water sample from drain line.
SRSDG 1040 = 

[320]
Title   = Cleaning: Chem Residual Timeout
Message = During Chemical Disinfection Flush\n-user residual sampling timed out.
SRSDG 1043 = 

[321]
Title   = DG Fault: UVo Error
Message = Call service to schedule a repair.
SRSDG 1069 = 

[322]
Title   = HD POST Alarm: UI Invalid Year
Message = Call service to schedule a repair.