[Sample^Water Sample]
Place cup in the water sampling pocket. Press and hold the "Water Sample" button. = water sampling_v2.png

[Sample^Water Sample Result]
Test the water sample per your clinic's instructions and enter the result. = temp_water_test.png

[Sample^Water Sample Result Failed]
Water sample result failed. = logo.png

[Consumables^Consumables Installation]
Open the DG concentrate door. = concentrate door open-v1.png
Remove the bottom acid/bicarbonate cap. = remove Acid_Bicab  cap-v2.png
Connect the acid concentrate to the acid port. = connect acid line v2-01.png
Connect the bicarbonate concentrate to the bicarbonate port. = connect bicarb ine-v2-01

[Disposables^Cartridge Installation]
Open the front panel door. = door up v2.png
Unlock the pump track by moving the lever to its upward position. = cassette clamp release v1.png
Install the cartridge using the alignment pins. = insert cassette v2-01-01.png
Lock the pump track by moving the lever to its downward position. = cassette clamp lock v2-01.png

[Disposables^Cartridge Connection]
Connect the cartridge blood and dialysis fluid lines to the the dialyzer. = filter connect_72.png
Insert dialyzer into the clamps. = filter load_72.png
Connect the cartridge tubing line to the air vent port. = PBo connect_72.png
Remove the top dialysis fluid cap DG system. = remove top cap v2-01.png
Connect the cartridge dialysis fluid lines to the DG fluid ports. = Dialysate lines to DG Y v4-01.png

[Disposables^Heparin Syringe]
Fill a syringe with heparin and connect the cartridge heparin tubing line. = syringe connect_72.png
Insert syringe into infusion pump housing. = syringe connected insert v2.png

[Disposables^Saline Bag]
Hang the saline bag on the left side hook. Spike a saline bag and connect it to the cartridge saline line. = saline connect_72.png

[Connection^Patient Connection]
Wash your hands and establish vascular access per your clinic's instructions. = logo.png
Pinch arterial clamp and venous clamp on located on the cartridge patient lines. = pinch paient lines v2.png
Remove arterial and venous shunt. = untwist stunt_72.png
Connect arterial and venous cartridge lines to your patient access lines. = alt connect fistula_72.png

[Connection^Start Treatment]
Unpinch arterial clamp and venous clamp located on the cartridge patient lines. = unclamp_patient_lines_temp


[^Rinseback Setup]
Pinch arterial line and saline bag line. = logo.png
Connect arterial line to the saline bag. = arterial to saline_v1.png
Unpinch arterial line and saline back line. = logo.png

 
[^Rinseback Complete]
Pinch arterial and venous line after rinseback is complete. = pinch paient lines v2.png

[Disconnection^Patient Disconnection]
Pinch arterial clamp and venous clamp on located on the cartridge patient lines and access lines. = pinch paient lines v2.png
Disconnect arterial and venous cartridge lines from your patient access lines. = Remove_patient connection temp.png

[Disposables^Disposables Removal]
Shunt the arterial and venous lines on the cartridge. = Twist shunt_temp.png
Disconnect the cartridge tubing line connected to the air vent port. = pbo release v1.png
Remove heparin syringe from the infusion pump housing. = syringe removal v1.png
Disconnect cartridge dialysate lines and connect ends together. Install top dialysis fluid cap. = install top cap v1-01.png
Disconnect acid and bicarbonate concentrates. Install bottom concentrate fluid cap. = install lower cap v1-01.png
Unlock the pump track by moving the lever to its upward position. = cassette clamp release v1.png
Remove cartridge and dialyzer from the HD device. = logo.png


[^Recirculate]
Recirculate 0 =logo.png
Recirculate 1 =logo.png
Recirculate 2 =logo.png

[Disinfection^Disinfection]
Disinfection1=logo.png
Disinfection2=logo.png
Disinfection3=logo.png

[Chemical Disinfect^Chemical Disinfect]
Disinfection1=logo.png