[0]
Title     = 
ListTitle = 
Message   = Indication for when no alarms is a possible situation

[1]
Title     = HD POST: Stuck Button
ListTitle = Stop or Off button are pressed for more than 1 sec during POST.
Message   = Stuck button POST failure.  Stop or Off button detected to be pressed for at least 1 second during test shortly after power up

[2]
Title     = HD POST: FPGA Compatibility
ListTitle = Minimum HD FPGA major revision is not compatible with this version of HD firmware or the FPGA Id is not correct.
Message   = HD FPGA POST failure

[3]
Title     = DG POST: FPGA Compatibility
ListTitle = Minimum DG FPGA major and minor revision are not equal to the FPGA major and minor revision in FPGA header
Message   = DG FPGA POST failure
SRSDG 602
SRSDG 814
SRSDG 1061 = 

[4]
Title     = HD POST: WD Safestate
ListTitle = If the following are not observed after 500ms of not petting the WD: 1. WD exp pin=low 2. 24V <= 5V 3. audio current >= 200mA If the following are not observed after 500ms of resumed WD petting at proper timing: 1. WD exp pin=high 2. 24V >= 22.6V 3. audio current <= 10 mA
Message   = HD Watchdog POST failure

[5]
Title     = DG POST: WD Safestate
ListTitle = If the following are not observed after 500ms of not petting the WD: 1. WD exp pin=low 2. 24V <= 5V If the following are not observed after 750ms of resumed WD petting at proper timing: 1. WD exp pin=high 2. 24V >= 22.6V
Message   = DG Watchdog POST failure
SRSDG 53 = 

[6]
Title     = HD POST: Proc- UI Comm
ListTitle = If the UI failed to checkin via the CAN bus within 40 seconds
Message   = UI communication POST failure.  UI failed to communicate within a reasonable time after power up

[7]
Title     = HD Alarm (Low): RTC Bat Low
ListTitle = If the RTC is not functional as indicated by the bits in the first 3 control registers.
Message   = Real-time clock configuration error

[8]
Title     = HD POST: Acc Vector
ListTitle = If the calculated vector length of the accelerometer x, y, z is not the nominal length.
Message   = HD accelerometer failed POST

[9]
Title     = DG POST: Acc Vector
ListTitle = If the calculated vector length of the accelerometer x, y, z is not the nominal length.
Message   = DG accelerometer failed POST
SRSDG 323 = 

[10]
Title     = HD POST: BLD Config Emb Mode
ListTitle = If the blood leak sensor embedded mode is unresponsive.
Message   = HD blood leak sensor embedded mode communication failed

[11]
Title     = Dial. Gen: Dialysate Temp Low
ListTitle = If the dialysate temperature is below the target temperature for a certain period of time.
Message   = Dialysate temperature is below the target temperature

[12]
Title     = HD POST: HD Image
ListTitle = If the calculated CRC of the HD image does not match the expected CRC.
Message   = HD firmware image integrity POST test failed

[13]
Title     = DG POST: DG Image
ListTitle = If the calculated CRC of the DG firmware image does not matched the expected CRC
Message   = DG firmware image integrity POST test failed
SRSDG 813 = 

[14]
Title     = DG POST: Usage Rec NVRAM CRC
ListTitle = If the DG usage information record's CRC does not match the calculated CRC in POST.
Message   = DG non-volatile usage information group invalid record CRC
SRSDG 957 = 

[15]
Title     = Dial. Gen: Dialysate Temp High
ListTitle = If the dialysate temperature is > 46 C for a certain period of time.
Message   = Dialysate temperature is out of high safety range

[16]
Title     = HD POST: Primary Alarm Current
ListTitle = If alarm audio current is NOT in expected range for than 1 second while alarm tone is being output
Message   = HD alarm audio failed POST

[17]
Title     = HD POST: UI POST Not Complete
ListTitle = If UI reports POST failed but did not trigger fault OR UI has not sent POST results within 2 seconds.
Message   = HD UI POST failed

[18]
Title     = Loss of DG Comm (DG ACK)
ListTitle = HD message to DG that requires acknowledge was not acknowledged within a certain time.
Message   = HD to DG comm error.

[19]
Title     = Dial. Gen: Dialysate Temp High
ListTitle = If the dialysate temperature is above the target temperature for a certain period of time.
Message   = Dialysate temperature is above the target temperature

[20]
Title     = DG POST: Conductivity Cal
ListTitle = If the calibration data that was received from NVDataMgmt is NOT legitimate
Message   = DG conductivity sensors invalid calibration record
SRSDG 16 = 

[21]
Title     = DG POST: Drain Line Vol Cal
ListTitle = If the calibration data that was received from NVDataMgmt is NOT legitimate
Message   = DG drain line volume invalid calibration record
SRSDG 936 = 

[22]
Title     = DG POST: Reservoir Vol Cal
ListTitle = If the calibration data that was received from NVDataMgmt is NOT legitimate
Message   = DG reservoirs invalid calibration record
SRSDG 935 = 

[23]
Title     = DG POST: Acid Conc Cal
ListTitle = If the non-volatile data is valid and if not raise the alarm
Message   = DG acid concentrate calibration record
SRSDG 934 = 

[24]
Title     = DG POST: Bicarb Conc Cal
ListTitle = If the non-volatile data is valid and if not raise the alarm
Message   = DG bicarb concentrate calibration record
SRSDG 933 = 

[25]
Title     = DG POST: Acc Cal
ListTitle = If the calibration data that was received from NVDataMgmt is NOT legitimate
Message   = DG accelerometer invalid calibration record
SRSDG 817 = 

[26]
Title     = HD POST: Acc Cal
ListTitle = If the accel calibration data that was received from NVDataMgmt is NOT legitimate.
Message   = HD accelerometer invalid calibration record

[27]
Title     = Process: Pre- Tx Wet Self- Test
ListTitle = BLD fails to complete zero sequence.
Message   = HD BLD sensor failed zero sequence

[28]
Title     = DG Fault: Conductivity RTD Comm
ListTitle = If the FPGA does not report fresh data for a certain period of time
Message   = DG two wire sensors FPGA fault
SRSDG 864 = 

[29]
Title     = HD POST: SP DAC Cal
ListTitle = If the heparin force sensor calibration data that was received from NVDataMgmt is NOT legitimate.
Message   = HD heparin force sensor invalid calibration record

[30]
Title     = HD Fault: SW Invalid State
ListTitle = If the specific software faults listed in alarm management SW faults has been detected
Message   = HD Software fault. Software found itself in an unexpected state

[31]
Title     = HD Fault: BP Current
ListTitle = If the measured MC current is not greater than BP_MAX_CURR_WHEN_STOPPED_MA or is not greater than BP_MAX_CURR_WHEN_RUNNING_MA.
Message   = Blood pump failed motor controller current check.  Too high when pump should be off or out of range when pump should be running

[32]
Title     = HD Fault: BP Speed
ListTitle = If the measured motor speed is greater than BP_MAX_MOTOR_SPEED_WHILE_OFF_RPM
Message   = Blood pump failed motor off check.  Measured speed while commanded off

[33]
Title     = HD Fault: BP Direction
ListTitle = If the set direction versus hall sensors direction versus sign of motor speed DOES NOT agree.
Message   = Blood pump failed motor direction check.  Measured vs. commanded

[34]
Title     = HD Fault: BP Rotor
ListTitle = If the delta of the measured motor speed and the commanded motor speed is not within tolerance.
Message   = Blood pump failed rotor speed check.  Mismatch with rotor and motor speeds

[35]
Title     = HD Fault: DPi Current
ListTitle = If the Motor Controller measured DPi pump current > 150.0 mA for more than 250.0 msec.
Message   = Dialysis inlet pump failed motor controller current check.  Too high when pump should be off or out of range when pump should be running

[36]
Title     = HD Fault: DPi Speed
ListTitle = If during command off state, the DPi pump motor speed is measured > 100.0 RMP.
Message   = Dialysis inlet pump failed motor off check.  Measured speed while commanded off

[37]
Title     = HD Fault: DPi Direction
ListTitle = If the set direction versus hall sensors direction DO NOT agree for more than 250.0 msec.
Message   = Dialysis inlet pump failed motor direction check.  Measured vs. commanded

[38]
Title     = HD Fault: DPi Rotor
ListTitle = If the measured motor speed versus the measured motor speed while controlling the target > 5.0 for more than 12 seconds.
Message   = Dialysis inlet pump failed rotor speed check.  Mismatch with rotor and motor speeds

[39]
Title     = HD Fault: DPo Current
ListTitle = If the DPo pump current  > 150.0 mA while stopped or Dpo current > 2000.0 mA for more than 2 seconds while running.
Message   = Dialysis outlet pump failed motor controller current check.  Too high when pump should be off or out of range when pump should be running

[40]
Title     = HD Fault: DPo Speed
ListTitle = If the Dpo pump current > 100.0 RPM while commanded off for more than 5000 msec.
Message   = Dialysis outlet pump failed motor off check.  Measured speed while commanded off

[41]
Title     = HD Fault: DPo Direction
ListTitle = If the DPo pump set direction does not agree with hall sensors or set direction does not agree with the sign of the motor speed for more than 25 msec.
Message   = Dialysis outlet pump failed motor direction check.  Measured vs. commanded

[42]
Title     = HD Fault: DPo Rotor
ListTitle = If DPo pump measured rotor speed does not agreed with the measured/commanded motor speed
Message   = Dialysis outlet pump failed rotor speed check.  Mismatch with rotor and motor speeds

[43]
Title     = DG Fault: Iso ADC Comm
ListTitle = If the FPGA does not report fresh data for a certain period of time
Message   = Main primary heater FPGA fault
SRSDG 954 = 

[44]
Title     = HD Fault: UI Comm
ListTitle = If the sub-system communication timeout has occurred.  UI is 5 seconds.  DG is 2 seconds.
Message   = User interface communication timeout

[45]
Title     = HD Fault: CAN CRC Com
ListTitle = If too many bad messages CRCs are received within a set period of time
Message   = Too many bad CRCs detected on received system messages

[46]
Title     = HD Fault: CAN ACK UI Com
ListTitle = If no retries left in the pending acknowlegement list.
Message   = System message that required acknowledgment was not acknowledged

[47]
Title     = 
ListTitle = 
Message   = 

[48]
Title     = HD Fault: UF Rate Tare Err
ListTitle = If the UF volume (refUFvolume - measureVolume) > 100.0 mL.
Message   = Ultrafiltration volume accuracy error during treatment

[49]
Title     = HD Fault: FPGA Com
ListTitle = If there are more than 3 comm errors in a 1 min period.
Message   = HD FPGA communication down for too long

[50]
Title     = DG Fault: Valve Control
ListTitle = If the read back FPGA valve states does not match the commanded valve states for a certain amount of time.
Message   = DG FPGA not accepting commanded valve states
SRSDG 26 = 

[51]
Title     = HD Fault: BP Speed
ListTitle = If measured motor speed versus commanded rotor speed exceeded limits.
Message   = Blood pump failed motor speed check.  Measured vs. commanded

[52]
Title     = HD Fault: DPi Speed
ListTitle = If measured motor speed versus commanded motor speed exceeded limits for more than 5 secs.
Message   = Dialysate inlet pump failed motor speed check.  Measured vs. commanded

[53]
Title     = HD Fault: DPo Speed
ListTitle = If measured motor speed versus commanded motor speed exceeded limits for more than 5 secs.
Message   = Dialysate outlet pump failed motor speed check.  Measured vs. commanded

[54]
Title     = HD Fault: Critical Data Err
ListTitle = If the critical data failed range check.
Message   = HD critical data integrity check failed

[55]
Title     = DG Fault: Critical Data Err
ListTitle = If the critical data failed range check.
Message   = DG critical data integrity check failed
SRSDG 921 = 

[56]
Title     = HD Fault: Acc Com
ListTitle = If no fresh sample of accelerometer data has been detected for more than 100 msec.
Message   = HD accelerometer error (no readings or FPGA reports error)

[57]
Title     = DG Fault: Acc Com
ListTitle = If no fresh sample of accelerometer data has been detected for more than 100 msec.
Message   = DG accelerometer error (no readings or FPGA reports error)
SRSDG 869
SRSDG 870 = 

[58]
Title     = HD Fault: Valve Home
ListTitle = If the number of failed homing > = 3 counts.
Message   = HD valve homing failed

[59]
Title     = HD Fault: Valve Transition Err
ListTitle = if the valve's transition time has timed out (3000msec)
Message   = HD valve transition time out

[60]
Title     = HD Fault: Valve Control
ListTitle = If the valve bit masks are not as expected in different valve control mode.
Message   = HD valve not functional

[61]
Title     = HD Fault: Valve Current
ListTitle = If the valve current is over the threshold of 1.0 A for 1000 msec.
Message   = HD valve current out of range

[62]
Title     = HD Fault: Valve Position
ListTitle = If the current position has deviated from the expected position for more than 1 second.
Message   = HD valve position out of target

[63]
Title     = 
ListTitle = 
Message   = 

[64]
Title     = DG Fault: Baro Range
ListTitle = If the barometric pressure is > 10.1 psi or < 15.4 psi for a certain period of time.
Message   = Barometric pressure is out of range
SRSDG 874 = 

[65]
Title     = Loss of DG Comm (Reject)
ListTitle = If the latest DG command response indicated invalid parameter
Message   = HD requests DG command with invalid parameter fault

[66]
Title     = HD POST: BLD Config Set Point
ListTitle = If the set point of the blood leak sensor does not match the set  point in the calibration record.
Message   = HD blood leak sensor set point set failure

[67]
Title     = Process: Pre- Tx Remove Cartridge
ListTitle = If the blood pump pressure > 5000
Message   = HD blood pump occlusion self-test failure alarm

[68]
Title     = Dial. Gen: Dialysate not ready
ListTitle = If the recirculation level has exceeded the max allowed
Message   = HD active reservoir recirculation out of range

[69]
Title     = HD POST: BLD Cal
ListTitle = If the BLD data that was received from NVDataMgmt is NOT legitimate.
Message   = HD blood leak sensor invalid calibration record

[70]
Title     = Process: Pre- Tx Remove Cartridge
ListTitle = If arterial pressure < -300 or > 100 mmHg
Message   = HD arterial pressure self-test failure alarm

[71]
Title     = Process: Pre- Tx Remove Cartridge
ListTitle = If the venous pressure < -100 or > 600 mmHg
Message   = HD venous pressure self-test failure alarm

[72]
Title     = Loss of DG Comm (LC)
ListTitle = No new load cell data for 2 seconds.
Message   = HD No load cell data message receive at least once every 2 seconds

[73]
Title     = Loss of DG Comm (TDI/TRO)
ListTitle = No new dialysate temperature data for 2 seconds.
Message   = HD No dialysate temperature data message received at least once every 2 seconds

[74]
Title     = DG Fault: UVi On No Flow
ListTitle = If the inlet UV reactor is on while VPi is closed for a certain period of time.
Message   = DG inlet UV reactor is on while there is no flow
SRSDG 600 = 

[75]
Title     = HD Fault: Syringe DAC
ListTitle = If the calibration data that was received from NVDataMgmt and the DAC voltage with syringe retracted are not within tol.
Message   = HD syringe pump self-test failure alarm

[76]
Title     = HD Fault: Voltage Monitor
ListTitle = If the HD monitored voltages are out of range for a certain period of time.
Message   = HD monitored voltage is out of range

[77]
Title     = DG Fault: Voltage Monitor
ListTitle = If the DG monitored voltages are out of range for a certain period of time.
Message   = DG monitored voltage is out of range
SRSDG 46
SRSDG 866
SRSDG 1088 = 

[78]
Title     = HD Fault: Syringe Pump Enc Dir
ListTitle = If the measured encoder direction of the syringe pump does not agree with the expected direction
Message   = HD syringe pump direction (from encoder) error

[79]
Title     = HD Fault: Syringe Pump Drv Dir
ListTitle = If the measured direction of the syringe pump motor controller does not agree with the expected direction
Message   = HD syringe pump direction (from controller) error

[80]
Title     = HD Fault: Syringe Pump Driver
ListTitle = If the FPGA reported the syringe pump fault
Message   = HD syringe pump fault reported by FPGA

[81]
Title     = HD Fault: Syringe Pump OT
ListTitle = If the syringe pump position is deemed to have overtraveled
Message   = HD syringe pump over travel error

[82]
Title     = HD Fault: Syringe Pump DAC Err
ListTitle = If the syringe pump DAC write error is reported by the FPGA
Message   = HD syringe pump DAC write failure

[83]
Title     = HD Fault: Syringe Pump On Err
ListTitle = If the syringe pump is on while the blood pump is off
Message   = HD syringe pump is running while the BP is off

[84]
Title     = DG POST: DG RTC Time
ListTitle = If DG RTC set year is < 2021.
Message   = DG RTC set year is invalid
SRSDG 815 = 

[85]
Title     = Blood Stop: Cartridge Lever Open
ListTitle = If the pump track lever is detected as unlatched when it should be.
Message   = HD pump track lever is not fully latched

[86]
Title     = HD POST: HD RTC Time
ListTitle = If HD RTC set year is < 2021.
Message   = HD RTC set year is invalid

[87]
Title     = DG POST: Heat Cal
ListTitle = If the heating paramters' non-volatile record's CRC does not match the calculated CRC.
Message   = DG heating parameters invalid calibration record
SRSDG 929 = 

[88]
Title     = DG Fault: CP1 CP2 Speed Range
ListTitle = Hall sensor pulse to pulse timing is < 1ms (speed too fast).
Message   = DG concentrate pump hall sensor out of range.

[89]
Title     = DG Fault: UVo On No Flow
ListTitle = If the outlet UV reactor is on while the RO flow is less than 200 mL/min.
Message   = DG outlet UV reactor is on while there is no flow
SRSDG 599 = 

[90]
Title     = DG Fault: LC A1/B1 Comm
ListTitle = If the FPGA does not report fresh data for a certain period of time.
Message   = DG load cells A1/B1 FPGA fault
SRSDG 604 = 

[91]
Title     = Loss of DG Comm (FMD)
ListTitle = If not receiving new dialysate flow readings in expected interval (3 seconds)
Message   = HD No dialysate flow data received in the last 3 seconds

[92]
Title     = 
ListTitle = 
Message   = 

[93]
Title     = DG Fault: RO Permeate Cond High
ListTitle = If the outlet primary conductivity sensor, CPo is greater than 30 uS/cm for a certain period of time.
Message   = DG outlet primary conductivity sensor out of range
SRSDG 430 = 

[94]
Title     = DG Fault: Pressure Sensor Range
ListTitle = If either of the pressure sensors is < 0 psia or > 200 psia for DG pressure sensors.
Message   = DG pressure sensor out of range
SRSDG 629 = 

[95]
Title     = DG Fault: WD Error
ListTitle = If the watchdog signal is low while not in POST.
Message   = DG watchdog expired
SRSDG 907 = 

[96]
Title     = Dial. Gen: Inlet Water Temp High
ListTitle = If the inlet water temperature is > 37 C.
Message   = DG inlet water temperature out of range
SRSDG 410 = 

[97]
Title     = Dial. Gen: Dialysate Cond.
ListTitle = If the average acid or bicard conductivity is > 5% of the normal acid and bicarb conductivity values.
Message   = DG fill conductivity out of range
SRSDG 397 = 

[98]
Title     = HD Alarm (Low): Battery Com
ListTitle = If battery I2C communication fault persistence count > 5.
Message   = HD battery or battery charger communication fault

[99]
Title     = HD Fault: Syringe Pump Stall
ListTitle = If syringe pump measured rate < stall speed threshold (0.05) and the ramp up has been restarted 3 times after stall has been detected.
Message   = HD syringe pump stall alarm

[100]
Title     = 
ListTitle = 
Message   = 

[101]
Title     = HD POST: UI- Proc Comm
ListTitle = If the HD is not communicating with the UI during POST.
Message   = UI POST FW Communication failure

[102]
Title     = Cleaning: Tpo THD Temp Delta
ListTitle = If temperature gradient between Tpo and Thd exceeds maximum 15°C.
Message   = DG heat disinfection temperature gradient out of range
SRSDG 856
SRSDG 930 = 

[103]
Title     = HD POST: Cal NVRAM CRC
ListTitle = If the computed CRC of the calibration group record is not equal to the record CRC.
Message   = HD non-volatile calibration group invalid record CRC

[104]
Title     = HD Fault: Air Trap Sensor
ListTitle = If the air trap level readings are not valid for more than 2 seconds.
Message   = Air trap level sensors reporting illegal combination of air/fluid

[105]
Title     = DG POST: Cal NVRAM CRC
ListTitle = If the DG NVDATAMGMT CAL group calculated CRC does not matched the expected CRC.
Message   = DG non-volatile system group invalid record CRC
SRSDG 608 = 

[106]
Title     = DG POST: Flow Sensor Cal
ListTitle = If the calculated CRC of the flow sensors calibration record does not match the calibration records' CRC.
Message   = DG flow sensors calibration error
SRSDG 820
SRSDG 821
SRSDG 1087 = 

[107]
Title     = DG Fault: DG Restarted
ListTitle = If DG reports being in any mode other than idle, drain, fill or fault during pre-tx, tx, or post-tx modes - means DG restarted unexpectedly and is no longer in sync w/ HD.
Message   = HD reports DG restarted fault

[108]
Title     = HD Fault: Syringe Pump ADC Com
ListTitle = If the ADC read is not fresh after POST init and the ADC read counter has not changed.
Message   = HD syringe pump ADC error

[109]
Title     = HD Fault: Syringe Pump Vol
ListTitle = If the volume delivered is off by more than 5% or 0.1mL.
Message   = HD syringe pump volume check error

[110]
Title     = HD Fault: Syringe Pump Speed
ListTitle = If the syringe measured rate is off by more than 5% or 0.1mL.
Message   = HD syringe pump speed check error

[111]
Title     = HD Fault: Syringe Pump Speed
ListTitle = If the syringe pump position is not equal to its last position.
Message   = HD syringe pump not stopped in off state error

[112]
Title     = DG Fault: LC A2/B2 Comm
ListTitle = If the FPGA does not report fresh data for a certain period of time.
Message   = DG load cells A2/B2 FPGA fault
SRSDG 953 = 

[113]
Title     = DG Fault: DRP Current
ListTitle = If the DG drain pump current > 2.2 A when it is in open loop or if the current > 0.1 A when it is off.
Message   = DG drain pump current out of range
SRSDG 890 = 

[114]
Title     = Process: Pre- Tx Wet Self- Test
ListTitle = If the venous air bubble self test did not detect bubble for more than 500 msec.
Message   = HD venous air bubble detector self-test failure

[115]
Title     = DG Fault: Temp Sensor Range
ListTitle = If the measured temperature  < 0 C or > 80 C for the non-fluid inline sensors and > 120 C for the fluid sensors.
Message   = DG temperature sensor out of range
SRSDG 224 = 

[116]
Title     = HD Alarm (Low): SD- Card Error
ListTitle = SD card is non-operational
Message   = SD card is non-operational

[117]
Title     = Loss of HD Comm (HD ACK)
ListTitle = If no retries left in the pending acknowlegement list.
Message   = System message that required acknowledgment was not acknowledged
SRSDG 909 = 

[118]
Title     = DG Fault: RTC Config
ListTitle = If the RTC configuration registers report an error.
Message   = DG RTC configuration error
SRSDG 43 = 

[119]
Title     = DG Alarm (Low): RTC Bat Low
ListTitle = If the RTC battery bit report a low alarm.
Message   = DG RTC battery low
SRSDG 908 = 

[120]
Title     = Process: Pre- Tx Wet Self- Test
ListTitle = If the HD pre-treatment wet self test failed.
Message   = HD pre-treatment wet prime test failure

[121]
Title     = DG Fault: Prim Heater Lg Control
ListTitle = If the main primary heater's voltage is out of range.
Message   = DG main primary heater voltage out of range
SRSDG 611 = 

[122]
Title     = DG Fault: Prim Heater Sm Control
ListTitle = If the small primary heater's voltage is out of range.
Message   = DG small primary heater voltage out of range
SRSDG 612 = 

[123]
Title     = DG Fault: Trimmer Heater Control
ListTitle = If the trimmer voltage is out of range.
Message   = DG trimmer heater voltage out of range
SRSDG 613 = 

[124]
Title     = Blood Stop: Blood Clot Risk
ListTitle = In treatment end paused state for > 5 minutes.
Message   = HD end of treatment alarm (high priority - user still not acting to end treatment)

[125]
Title     = Blood Stop: Blood Clot Risk
ListTitle = If in treatment stop sub mode when blood is in the tubing, the blood sitting counter exceeded 5 minutes.
Message   = Blood sitting too long after treatment stopped by user alarm (> 5 min)

[126]
Title     = Blood Stop: Dialyzer Blood Leak
ListTitle = If the blood leak is detected based on the blood leak status reported by the sensor.
Message   = HD blood leak detected alarm

[127]
Title     = Blood Stop: Venous Pres. Low
ListTitle = If the venous pressure < TREATMENT_PARAM_VEN_PRESSURE_LOW_LIMIT.  Or expanded pressure limits based on mode of operation.
Message   = Venous pressure too low during treatment

[128]
Title     = Blood Stop: Venous Air Bubble
ListTitle = If bubbles are detected during the treatment.
Message   = HD venous air bubble detected alarm

[129]
Title     = Blood Stop: Dialyzer Blood Leak Bypass
ListTitle = If the blood leak is detected in treatment, the HD device transitions to treatment stop and runs in bypass until there is no blood detected. The user can hit end treatment anytime.
Message   = HD blood leak detected and it is in the process of attempting to remove the bubbles/foam

[130]
Title     = Blood Stop: Venous Pres. High
ListTitle = If the venous pressure >  TREATMENT_PARAM_VEN_PRESSURE_HIGH_LIMIT.  Or expanded pressure limits based on mode of operation.
Message   = Venous pressure too high during treatment

[131]
Title     = Blood Stop: Arterial Pres. Low
ListTitle = If the arterial pressure < TREATMENT_PARAM_ART_PRESSURE_LOW_LIMIT.  Or expanded pressure limits based on mode of operation.
Message   = Arterial pressure too low during treatment

[132]
Title     = Blood Stop: Arterial Pres. High
ListTitle = If the arterial pressure > TREATMENT_PARAM_ART_PRESSURE_HIGH_LIMIT.  Or expanded pressure limits based on mode of operation.
Message   = Arterial pressure too high during treatment

[133]
Title     = DG Fault: Fluid Leak in DG
ListTitle = If the fluid leak is detected as reported by the fluid leak detector.
Message   = DG fluid leak detected alarm
SRSDG 328 = 

[134]
Title     = Blood Stop: Fluid Leak in HD
ListTitle = If the fluid leak is detected as reported by the fluid leak detector.
Message   = HD fluid leak detected alarm

[135]
Title     = Blood Stop: HD Shock Detected
ListTitle = If the system experienced excessive shock > 2.5 g.
Message   = HD experienced large acceleration

[136]
Title     = Dial. Gen: Shock- Vibration
ListTitle = If the system experienced excessive shock > 2.5 g.
Message   = DG experienced large acceleration
SRSDG 327 = 

[137]
Title     = Blood Stop: HD Tilted
ListTitle = If the system experienced excessive tilt x and y axis angle  > 7 deg for more than 1 sec.
Message   = HD tilt exceeds maximum

[138]
Title     = Dial. Gen: Tilt
ListTitle = If the system experienced excessive tilt x and y axis angle  > 7 deg for more than 1 sec.
Message   = DG tilt exceeds maximum
SRSDG 326 = 

[139]
Title     = Loss of AC Power
ListTitle = The HD Software shall trigger an alarm if an AC power loss is detected while the HD system is in standby, service, or treatment parameters mode.
Message   = HD AC power lost alarm

[140]
Title     = Loss of DG Comm (Timeout)
ListTitle = If DG communication timeout is detected for more than 2 seconds.
Message   = Dialysate generator communication timeout

[141]
Title     = Blood Stop: Air Trap Fill
ListTitle = If the air trap fill timeout during treatment.
Message   = Air trap fill timeout during treatment

[142]
Title     = Blood Stop: Blood Pump Occlusion
ListTitle = If blood occlusion is detected > OCCLUSION_THRESHOLD_OFFSET + bloodPumpOcclusionAfterCartridgeInstall
Message   = Blood pump occlusion detected

[143]
Title     = DG Fault: TRo TDi Delta
ListTitle = If TDi and TRo have drifted for more 1 C for a certain period of time.
Message   = DG dialysate temperature sensors drift timeout.
SRSDG 912 = 

[144]
Title     = Cleaning: Inlet Water Cond High
ListTitle = Inlet water conductivity > 2000 uS/cm. Inlet water conductivity > 100 uS/cm (PURE WATER MODE). In cleaning mode
Message   = DG cleaning mode inlet water conductivity out of high range
SRSDG 1066
SRSDG 1054
SRSDG 970 = 

[145]
Title     = Dial. Gen: Acid Conc. Cond.
ListTitle = If the conductivity value for the acid concentrate is out of range for more than 45 secs.
Message   = DG Concentrate conductivity after adding acid out of range alarm
SRSDG 846 = 

[146]
Title     = DG POST: DG RTC Timer
ListTitle = If RTC and timer are not aligned on 1 second elapsed time.
Message   = DG RTC vs. Timer accuracy error
SRSDG 312 = 

[147]
Title     = Dial. Gen: Dialysate not ready
ListTitle = If dialysate conductivity is not with 5% of the TCD
Message   = DG dialysate generation conductivity fault alarm
SRSDG 398 = 

[148]
Title     = Cleaning: Inlet Water Temp High
ListTitle = Inlet temperature > 37 C.
Message   = Cleaning Mode Inlet water temperature too high
SRSDG 1065
SRSDG 1053
SRSDG 969 = 

[149]
Title     = HD Fault: WD Error
ListTitle = If the watchdog signal is low while not in POST.
Message   = HD watchdog expired

[150]
Title     = Dial. Gen: Inlet Water Cond High
ListTitle = Inlet water conductivity > 2000 uS/cm. Inlet water conductivity > 100 uS/cm (PURE WATER MODE).
Message   = Inlet water conductivity too high
SRSDG 391 = 

[151]
Title     = Dial. Gen: Inlet Water Cond Low
ListTitle = Inlet water conductivity < 200 uS/cm. Inlet water conductivity low disabled (PURE WATER MODE).
Message   = Inlet water conductivity too low
SRSDG 826 = 

[152]
Title     = Dial. Gen: Inlet Water Pres Low
ListTitle = Inlet water pressure < 25 PSI.
Message   = Inlet water pressure too low
SRSDG 417 = 

[153]
Title     = Process: Pre- Tx Terminated
ListTitle = In Pre-Treatment Recirculation for 120 minutes (escalation of alarm 213)
Message   = HD prime completed high priority alarm

[154]
Title     = Cleaning: Inlet Water Cond Low
ListTitle = Inlet water conductivity < 200 uS/cm. Inlet water conductivity low disabled (PURE WATER MODE). In cleaning mode
Message   = Cleaning mode inlet water conductivity too low
SRSDG 1067
SRSDG 1055
SRSDG 971 = 

[155]
Title     = Loss of DG Comm (Reservoir)
ListTitle = No new reservoir data for 2 seconds.
Message   = HD No reservoir data message receive at least once every 2 seconds

[156]
Title     = Loss of DG Comm (Op Mode)
ListTitle = No DG op mode for 2 seconds.
Message   = HD No DG op mode message receive at least once every 2 seconds

[157]
Title     = Cleaning: Chem Disinf PAA Prime
ListTitle = If the disinfectant acid line is not primed within a certain period of time.
Message   = Chemical disinfect priming the acid line timeout
SRSDG 988 = 

[158]
Title     = Dial. Gen: Inlet Water Temp Low
ListTitle = Inlet temperature < 24 °C for 5 seconds.
Message   = Inlet water temperature low
SRSDG 408 = 

[159]
Title     = Cleaning: Chem Disinf Connect Cap
ListTitle = Start of chemical disinfect flush.
Message   = Close concentrate line be able to flush it
SRSDG 1044 = 

[160]
Title     = HD Fault: BP Rotor Max Speed
ListTitle = If blood pump motor speed exceeded 100.0 RPM.
Message   = Blood pump rotor speed too high

[161]
Title     = DG Fault: HD- DG Comm
ListTitle = If >= 5 bad CRCs detected on received CAN messages within 10 minutes.
Message   = Too many bad CRCs detected on received system messages
SRSDG 122 = 

[162]
Title     = DG Fault: Proc- FPGA Clock
ListTitle = If the FPGA clock speed is relatively close to the processor clock for a certain period of time.
Message   = FPGA clock speed failure
SRSDG 867 = 

[163]
Title     = Dial. Gen: UF Rate Check
ListTitle = If the delta volume of the active reservoir exceeded 50.0 g (MAX_ACTIVE_LOAD_CELL_CHANGE_G).
Message   = HD sees primary load cell for reservoir 1 change too much too fast

[164]
Title     = Dial. Gen: UF Rate Check
ListTitle = If the delta volume of the active reservoir exceeded 50.0 g (MAX_ACTIVE_LOAD_CELL_CHANGE_G).
Message   = HD sees primary load cell for reservoir 2 change too much too fast

[165]
Title     = Blood Stop: Blood Clot Risk
ListTitle = If the maximum time inrinseback operation has been exceeded.
Message   = HD in treatment rinseback operation timeout

[166]
Title     = 
ListTitle = 
Message   = 

[167]
Title     = Blood Stop: Door Open
ListTitle = If the cartridge door is opened as reported by the FPGA.
Message   = HD cartridge door opened alarm

[168]
Title     = 
ListTitle = 
Message   = 

[169]
Title     = DG Fault: Dialysate Flow Sens Rg
ListTitle = If the dialysate flow rate > 2.00 L/min.
Message   = Dialysate flow rate out of range
SRSDG 643 = 

[170]
Title     = Heparin Syringe Empty
ListTitle = If the syringe pump position is near empty position.
Message   = HD syringe empty alarm

[171]
Title     = Process: Pre- Tx Hep. Pump Occ.
ListTitle = If the pressure sensor voltage reading > SYRINGE_FORCE_OCCLUSION_THRESHOLD_V.
Message   = HD syringe pump occlusion alarm

[172]
Title     = Process: Pre- Tx Not Enough Hep.
ListTitle = If the estimated syringe volume needed for treatment is not sufficient
Message   = HD syringe pump not enough Heparin alarm

[173]
Title     = HD Fault: RTC Config
ListTitle = If the RTC configuration registers report an error.
Message   = HD RTC configuration error

[174]
Title     = HD POST: HD RTC Timer
ListTitle = If RTC and timer are not aligned on 1 second elapsed time.
Message   = HD RTC vs. Timer accuracy error

[175]
Title     = HD Fault: Pump Commutation Err
ListTitle = If the set pump direction does not agree with the hall sensor direction.
Message   = HD pump commutation error

[176]
Title     = 
ListTitle = 
Message   = 

[177]
Title     = DG Fault: Software Invalid State
ListTitle = If the specific software faults listed in alarm management SW faults has been detected
Message   = DG software fault.  Software found itself in an unexpected state
SRSDG 919 = 

[178]
Title     = HD Fault: UI- Proc Comm
ListTitle = If the HD stops communicating with the UI.
Message   = HD communication timeout
 = SRSUI 1066

[179]
Title     = DG Fault: FPGA Com
ListTitle = If retries for commands exceeds limit or FPGA reports comm error.
Message   = DG FPGA communication down for too long
SRSDG 605 = 

[180]
Title     = DG Fault: RO Flow Sensor Range
ListTitle = If the RO flow rate > 2.00 L/min.
Message   = RO flow rate out of range
SRSDG 883 = 

[181]
Title     = DG Fault: Tare Out of Range
ListTitle = If the load cell weight is out of range for tare.
Message   = DG load cells weight out of range for tare
SRSDG 849
SRSDG 838 = 

[182]
Title     = DG POST: LC Cal
ListTitle = If the CRC of load cells calibration data does not match the calculated CRC.
Message   = DG load cells invalid calibration
SRSDG 162 = 

[183]
Title     = Cleaning: Invalid Resv Transfer
ListTitle = If the half full reservoir is filled prior to filling the reservoir that is supposed to overflow to the half full reservoir.
Message   = DG invalid load cell value
SRSDG 851 = 

[184]
Title     = DG Fault: UVi Error
ListTitle = If the inlet reactor are not healthy.
Message   = Inlet reactor not healthy
SRSDG 559 = 

[185]
Title     = DG Alarm (Low): Fan Speed
ListTitle = If the fan RPM is out of Min/Max range.
Message   = DG fan RPM out of range
SRSDG 628 = 

[186]
Title     = DG Fault: CP1/CP2 Fault
ListTitle = If the concentrate pumps fault is reported by the FPGA.
Message   = DG concentrate pump fault
SRSDG 891 = 

[187]
Title     = DG Fault: CP1 Speed Fault
ListTitle = If the concentrate pump CP1 speed > 0.02 tolerance for a certain period of time.
Message   = DG concentrate pump CP1 speed control error
SRSDG 905 = 

[188]
Title     = DG Fault: CP2 Speed Fault
ListTitle = If the concentrate pump CP1 speed > 0.02 tolerance for a certain period of time.
Message   = DG concentrate pump CP2 speed control error
SRSDG 906 = 

[189]
Title     = DG Fault: DRP Speed Fault
ListTitle = If the drain pump RPM > 100.0 of the target RPM.
Message   = DG drain pump RPM out of range
SRSDG 448 = 

[190]
Title     = DG Fault: DRP Speed Not Off
ListTitle = If the pump is in off state and the RPM is greater than the minimum RPM of 300.0 RPM.
Message   = DG drain pump off fault

[191]
Title     = DG Fault: RO Flow High
ListTitle = If the RO flow rate > 10% from the target flow rate.
Message   = DG flow rate out of upper range
SRSDG 885 = 

[192]
Title     = DG Fault: RO Flow Low
ListTitle = If the RO flow rate < 10% from the target flow rate.
Message   = DG flow rate out of lower range
SRSDG 945 = 

[193]
Title     = 
ListTitle = 
Message   = 

[194]
Title     = DG Fault: RO Driver Feedback
ListTitle = If the DG RO pump duty cycle is out of range by 5% of the target duty cycle for a certain period of time.
Message   = DG RO pump duty cycle out of range
SRSDG 881 = 

[195]
Title     = DG Fault: RO Pump High Pressure
ListTitle = If the DG RO pump pressure > 135 psi for a certain period of time.
Message   = DG RO pump pressure out of range
SRSDG 925 = 

[196]
Title     = DG Fault: CPi/CPo Comm
ListTitle = If the FPGA reports error for a certain period of time.
Message   = DG CPi/CPo conductivity sensors FPGA fault
SRSDG 955 = 

[197]
Title     = DG Fault: CD1/CD2 Comm
ListTitle = If the FPGA reports error for a certain period of time.
Message   = DG CD1/CD2 conductivity sensors FPGA fault
SRSDG 956 = 

[198]
Title     = DG Fault: HP On With No Flow
ListTitle = If the RO flow is < 0.2 L/min for a certain period of time.
Message   = DG primary heater while RO flow is low
SRSDG 872 = 

[199]
Title     = DG Fault: HR On With No Flow
ListTitle = If the FMD flow is ≤ 0 mL/min (raw) for a certain period of time.
Message   = DG trimmer heater while dialysate flow is low
SRSDG 871 = 

[200]
Title     = DG Fault: Thermistor Range
ListTitle = If thermistor > 80.0 C or < 0.0 C.
Message   = DG thermistor or temperature sensor out of range
SRSDG 178 = 

[201]
Title     = Process: Pre- Tx Wet Self- Test
ListTitle = If the pre-treatment wet flow test has failed.
Message   = HD pre-treatment wet flow test failure

[202]
Title     = Process: Pre- Tx Dry Self- Test
ListTitle = If the pre-treatment dry pressure normal test failed.
Message   = HD pre-treatment dry pressure normal test failure

[203]
Title     = 
ListTitle = 
Message   = 

[204]
Title     = DG Fault: RO Rejection
ListTitle = If RO rejection ratio > 0.1
Message   = RO rejection ratio out of range
SRSDG 429 = 

[205]
Title     = DG Fault: Cond Sensors Error
ListTitle = If conductivity sensor reports 0x11 for more than 2 consecutive reads.
Message   = Conductivity sensor fault
SRSDG 913 = 

[206]
Title     = DG Fault: Reservoir Fill Timeout
ListTitle = If DG dialysate fill  > 5 minutes.
Message   = DG dialysate fill runs out of time
SRSDG 437 = 

[207]
Title     = DG Fault: FMP Flow Rate Error
ListTitle = If integrated Volume To Load Cell Reading Percent > 0.1.
Message   = DG flow meter check failure alarm
SRSDG 240 = 

[208]
Title     = Blood Stop: Venous Pres. High
ListTitle = If the venous pressure is > set limit + 50 mmHg if HD is in treatment or pre-treatment mode.
Message   = HD venous line occlusion fault

[209]
Title     = Cleaning: Flush Circ Error
ListTitle = If the integrated volume < 0.1 for more than 60 secs.
Message   = DG drain circulation line timeout
SRSDG 980 = 

[210]
Title     = HD Alarm (Low): Battery Fault
ListTitle = If the battery pack status error is detected from the slave device I2C address 0x0B.
Message   = HD battery pack detected an error

[211]
Title     = Blood Stopped:  Warning
ListTitle = During treatment stop sub-mode, if the blood is in the line for more than 4 minutes.
Message   = Blood sitting too long warning (> 4 min)

[212]
Title     = Blood Stopped:  Warning
ListTitle = During treatment end paused state, if the blood is in the line for more than 4 minutes.
Message   = Blood sitting too long warning (> 4 min)

[213]
Title     = Process: Pre- Tx Prime Complete
ListTitle = In Pre-Treatment Recirculation for 90 minutes (escalation of alarm 226)
Message   = HD prime completed medium priority alarm

[214]
Title     = 
ListTitle = 
Message   = 

[215]
Title     = 
ListTitle = 
Message   = 

[216]
Title     = Process: End of Dialysis Tx
ListTitle = If the treatment ended successfully.
Message   = HD end treatment sub-mode timeout alarm

[217]
Title     = 
ListTitle = 
Message   = 

[218]
Title     = Process: Remove Syringe
ListTitle = If the syringe detection switch  > 2.0 volts.
Message   = HD syringe detected alarm

[219]
Title     = Blood Stop: Syringe Not Detected
ListTitle = If the syringe detection switch  < 2.0 volts.
Message   = HD syringe pump syringe removed alarm

[220]
Title     = DG Fault: THD RTD Comm
ListTitle = If the FPGA does not report fresh data for a certain period of time
Message   = DG THd sensor FPGA fault
SRSDG 947 = 

[221]
Title     = Blood Stop: Saline Bag Empty
ListTitle = If the measured arterial pressure < -300.0 mmHg for more than 250 msec.
Message   = HD Saline bag is empty

[222]
Title     = HD Fault: BP Occ Com
ListTitle = If the FPGA does not report fresh data or indicates an error for a certain period of time.
Message   = HD occlusion sensor FPGA fault

[223]
Title     = HD Fault: Art. Pres. Com
ListTitle = If the FPGA does not report fresh data for a certain period of time
Message   = HD arterial sensor FPGA fault

[224]
Title     = Blood Stopped: Treatment Pause
ListTitle = If the user has pressed the stop button.
Message   = Treatment stopped by user action - pressed stop button

[225]
Title     = Process: End of Treatment
ListTitle = If the treatment duration has exceeded the prescribed treatment time entered by the user.
Message   = HD end of treatment warning

[226]
Title     = Process: Pre- Tx Priming Complete
ListTitle = Start of Pre-Treatment Recirculation - notifiy user to proceed to patient connection
Message   = HD prime completed low priority alarm

[227]
Title     = 
ListTitle = 
Message   = 

[228]
Title     = Process: Pre- Tx Prime Timeout
ListTitle = During the pre-treatment prime state, if the prime saline purge air state exceeded 60 secs.
Message   = HD time out on prime sub-mode purge air state.

[229]
Title     = Process: Pre- Tx Prime Timeout
ListTitle = If the priming of the dialyzer dialysate flow path has exceeded the time limit.
Message   = HD prime dialysate dialyzer time out alarm

[230]
Title     = Process: Pre- Tx Prime Timeout
ListTitle = If the priming of the dialyzer bypass flow path has exceeded the time limit.
Message   = HD prime dialysate bypass time out alarm

[231]
Title     = Process: Pre- Tx Dry Self- Test
ListTitle = If the following dry self tests have failed: 1. handleDrySelfTestPressureSensorsState 2. handleDrySelfTestPressureSensorsNormalState
Message   = HD pre-treatment mode dry self-tests failure

[232]
Title     = Process: Pre- Tx Wet Self- Test
ListTitle = If the following wet self tests have failed: 1. handleWetSelfTestPrimeCheckState 2. handleWetSelfTestFirstDisplacementVerifyState 3. handleWetSelfTestSecondDisplacementVerifyState
Message   = HD pre-treatment mode wet self-tests failure

[233]
Title     = DG Fault: Baro Cal CRC
ListTitle = If the following happens: 1. The stored CRC in the sensor does not match the calculated CRC. 2. The CRC and coefficients have not been received from the sensor after 20 seconds from the power up.
Message   = DG barometric pressure sensor bad coefficients CRC
SRSDG 964
SRSDG 949
SRSDG 1089 = 

[234]
Title     = Dial. Gen: Inlet Water Pres High
ListTitle = If the inlet water pressure is > 80 psig.
Message   = DG inlet water pressure is too high
SRSDG 1037 = 

[235]
Title     = Process: Rinseback Complete
ListTitle = If there is no active alarm and rinseback has completed.
Message   = HD in treatment stopped sub-mode after rinseback completed (no escalation)

[236]
Title     = Process: Pre- Tx Dry Self- Test
ListTitle = If the air trap sensor reported AIR and bubble sensor detected bubbles.
Message   = HD needs new cartridge to be installed

[237]
Title     = 
ListTitle = 
Message   = 

[238]
Title     = Process: Pre- Tx Dry Self- Test
ListTitle = If the measured blood pump occlucsion pressure reading is < 5000 or > 24500.
Message   = HD no cartridge loaded or installed improperly alarm

[239]
Title     = Process: Post- Tx Remove Cartridge
ListTitle = In the post treatment state, if the cartridge has not been removed.
Message   = HD fail to remove cartridge alarm

[240]
Title     = Dial. Gen: Bicarb Conc. Cond.
ListTitle = If the conductivity value for bicarbonate concentrate is out of range for more than 45 secs.
Message   = Bicarb conductivity out of range during bicarb pump check alarm
SRSDG 482 = 

[241]
Title     = Cleaning: Resv Drain Timeout
ListTitle = If the DG reservoir drain is not complete in 120 secs.
Message   = DG reservoir drain time out
SRSDG 848
SRSDG 90
SRSDG 561
SRSDG 577
SRSDG 590
SRSDG 591
SRSDG 336
SRSDG 879
SRSDG 340
SRSDG 496
SRSDG 501
SRSDG 505
SRSDG 532
SRSDG 535
SRSDG 556
SRSDG 557
SRSDG 1048
SRSDG 1049
SRSDG 651
SRSDG 655
SRSDG 744
SRSDG 745
SRSDG 1004
SRSDG 1008
SRSDG 1019
SRSDG 1023
SRSDG 1033
SRSDG 1034 = 

[242]
Title     = Cleaning: Resv Fill Timeout
ListTitle = If the DG reservoir fill is not complete in 120 secs.
Message   = DG reservoir fill time out
SRSDG 850
SRSDG 573
SRSDG 574
SRSDG 579
SRSDG 580
SRSDG 492
SRSDG 493
SRSDG 498
SRSDG 499
SRSDG 508
SRSDG 509
SRSDG 519
SRSDG 690
SRSDG 691
SRSDG 703
SRSDG 711
SRSDG 1020
SRSDG 1024 = 

[243]
Title     = Cleaning: Fluid Loss Detected
ListTitle = If the reservoir level is drifted by 100 mL for more than 30 seconds.
Message   = DG reservoir leak time out
SRSDG 853 = 

[244]
Title     = Cleaning: Temp Sensor Check
ListTitle = If any of the temperature sensors are out of the average of the sensors by more than 3 C.
Message   = DG temperature sensors difference out of range
SRSDG 852 = 

[245]
Title     = Cleaning: Heat Disinfect Temp TO
ListTitle = If heating up to minimum temperature for heat disinfect failed after 4 hours.
Message   = DG heat disinfect target temperature time out (could not reach to temperature)
SRSDG 854 = 

[246]
Title     = Cleaning: RO Water Cond Error
ListTitle = If CPo and CD2 conductivity values are above 100 uS/cm.
Message   = DG chemical disinfect inlet conducitivty out of range

[247]
Title     = 
ListTitle = 
Message   = 

[248]
Title     = Cleaning: Chem Disinfect Proc
ListTitle = If TPo > 50 C after 1 second.
Message   = DG chemical disinfect out of target temperature

[249]
Title     = Cleaning: Chem Disinf PAA Cond
ListTitle = If CD2 < 150 uS/cm or CD2 > 650 uS/cm after 10 seconds.
Message   = DG chemical disinfect out of target conductivity
SRSDG 992 = 

[250]
Title     = Cleaning: Chem Disinf Connect PAA
ListTitle = Start of chemical disinfect
Message   = Insert the acid to start chemical disinfect
SRSDG 1046 = 

[251]
Title     = HD POST: Sys Rec NVRAM CRC
ListTitle = If the calculated CRC of the HD system record image does not match the expected CRC.
Message   = HD invalid system record

[252]
Title     = HD POST: Serv Rec NVRAM CRC
ListTitle = If the calculated CRC of the HD service record image does not match the expected CRC.
Message   = HD invalid service record

[253]
Title     = DG POST: Sys Rec NVRAM CRC
ListTitle = If the calculated CRC of the DG system record image does not match the expected CRC.
Message   = DG invalid system record
SRSDG 609 = 

[254]
Title     = DG POST: Serv Rec NVRAM CRC
ListTitle = If the calculated CRC of the DG service record image does not match the expected CRC.
Message   = DG invalid service record
SRSDG 610 = 

[255]
Title     = HD POST: UI Compatibility
ListTitle = If the compatibility revision field of the UI is not equal to SW_COMPATIBILITY_REV.
Message   = HD and UI software builds are not compatible

[256]
Title     = Cleaning: Chem Flush In Progress
ListTitle = If DG flush successfully started from the UI.
Message   = DG flush started
 = SRSUI 497

[257]
Title     = 
ListTitle = 
Message   = 

[258]
Title     = 
ListTitle = 
Message   = 

[259]
Title     = HD Fault: Temp Sensors Error
ListTitle = If thermistor reports temperature > 80.0 C or < 0.0 C for a certain period of time.
Message   = HD temperatures out of range

[260]
Title     = HD POST: UI Image
ListTitle = If the UI POST reports a shasum faillure.
Message   = UI POST Application Integrity (Sha256Sum) failure
 = SRSUI 1067

[261]
Title     = HD POST: UI CAN Driver
ListTitle = If the UI POST reports a can bus failure.
Message   = UI POST CANBus failure
 = SRSUI 1068

[262]
Title     = 
ListTitle = If the UI POST reports a display failure.
Message   = UI POST Display failure

[263]
Title     = HD POST: UI Touch Driver
ListTitle = If the UI POST reports a touch failure.
Message   = UI POST Touch failure
 = SRSUI 1070

[264]
Title     = HD POST: UI SD- Card
ListTitle = If the UI POST reports SD card failure.
Message   = UI POST SD-Card failure
 = SRSUI 1071

[265]
Title     = HD POST: UI RTC
ListTitle = If  the UI POST reports RTC failure.
Message   = UI POST RTC failure
 = SRSUI 1072

[266]
Title     = HD POST: UI WiFi
ListTitle = If the UI POST reports WiFi failure.
Message   = UI POST WiFi failure
 = SRSUI 1073

[267]
Title     = HD POST: UI Bluetooth
ListTitle = If the UI POST reports bluetooth failure.
Message   = UI POST Bluetooth failure
 = SRSUI 1074

[268]
Title     = HD POST: UI Ethernet
ListTitle = If the UI POST reports ethernet failure.
Message   = UI POST Ethernet failure
 = SRSUI 1075

[269]
Title     = HD POST: UI Sound
ListTitle = If the UI POST reports sound failure.
Message   = UI POST Sound failure
 = SRSUI 1076

[270]
Title     = HD POST: Proc Safestate
ListTitle = If the 24 volts power source is greater than 5.0 volts during safety shutdown self test state. If the 24 volts power source is less than 22.6 volts during safety shutdown self test recover state.
Message   = HD POST Safety Shutdown failure

[271]
Title     = DG POST: Proc Safestate
ListTitle = If the 24 volts power source is greater than 5.0 volts during safety shutdown self test state. If the 24 volts power source is less than 22.6 volts during safety shutdown self test recover state.
Message   = DG POST Safety Shutdown failure
SRSDG 822 = 

[272]
Title     = HD Alarm (Low): Fan Speed
ListTitle = If the fan RPM is out of Min/Max range.
Message   = HD Fan RPM out of range

[273]
Title     = 
ListTitle = 
Message   = 

[274]
Title     = 
ListTitle = 
Message   = 

[275]
Title     = HD Fault: Arterial Press Range
ListTitle = If the arterial pressure > 2000.0 mmHg or < -1500.0 mmHg.
Message   = HD arterial pressure sensor is reading out of range

[276]
Title     = HD Fault: Venous Press Range
ListTitle = If the venous pressure > 2000.0 mmHg or < -1500.0 mmHg.
Message   = HD venous pressure sensor is reading out of range

[277]
Title     = HD Fault: Occlusion Sens Range
ListTitle = If the blood pump occlusion count is < 2000.
Message   = HD BP occlusion sensor is reading out of range

[278]
Title     = DG Fault: Reservoir Overfill
ListTitle = If the active reservoir weight is > 1900.0 g.
Message   = HD active reservoir weight out of range.

[279]
Title     = DG Fault: Reservoir Drain
ListTitle = If the DG dialysate drain exceeded 120 seconds.
Message   = DG dialysate drain time out
SRSDG 752 = 

[280]
Title     = DG Fault: DRP Direction Fault
ListTitle = If the drain pump's direction is not 1 when draining.
Message   = DG drain pump invalid direction
SRSDG 888 = 

[281]
Title     = Dial. Gen: Acid Conc. Low
ListTitle = If the acid concentration bottle volume > 3240 (3340 - 100).
Message   = DG Acid concentration bottle low volume alarm
SRSDG 836 = 

[282]
Title     = Dial. Gen: Bicarb Conc. Low
ListTitle = If the bicarbonate concentration bottle volume > 3680 (3780 - 100).
Message   = DG Bicarbonate concentration bottle low volume alarm
SRSDG 837 = 

[283]
Title     = DG Fault: LC Range
ListTitle = If the weight of the DG load cells > 4500.0 g or < 0.0 g.
Message   = DG load cells weight out of range
SRSDG 615 = 

[284]
Title     = DG Fault: Redundant LC Check
ListTitle = If redundant load cells deviate by more than 60g after tare for 5 seconds.
Message   = DG load cells primary/back up drift out of range
SRSDG 383 = 

[285]
Title     = Cleaning: RO Permeate Sample In Progress
ListTitle = If DG RO permeate sample successfully started from UI.
Message   = DG RO permeate sample started

[286]
Title     = Cleaning: Conc Cap Removed
ListTitle = If the concentrate cap is not in the right position in the cleaning modes.
Message   = DG cap in wrong state

[287]
Title     = HD Fault: Proc- FPGA Clock
ListTitle = If during initialization mode, the difference between the processor clock speed and the FPGA clock speed > 1.
Message   = HD processor clock speed checks against FPGA clock failure

[288]
Title     = DG Fault: LC Drift Check
ListTitle = If redundant load cells deviate from start to end of a reservoir use during treatment by more than 10g.
Message   = HD load cell inconsistency

[289]
Title     = Cleaning: Dialysate Cap Removed
ListTitle = If the dialysate cap is not in the right position in the cleaning modes.
Message   = DG cap in wrong state
SRSDG 928 = 

[290]
Title     = HD Fault: Ven. Pres. Com
ListTitle = If the FPGA does not report fresh data for a certain period of time
Message   = HD venous sensor FPGA fault

[291]
Title     = Cleaning: Flush In Progress
ListTitle = If DG flush successfully started from the UI.
Message   = DG flush started

[292]
Title     = Cleaning: Heat Disinf In Progress
ListTitle = If DG heat disinfect successfully started from the UI.
Message   = DG heat disinfect started

[293]
Title     = Cleaning: Chem Disinfect In Progress
ListTitle = If DG flush successfully started from the UI.
Message   = DG chem disinfect started

[294]
Title     = Cleaning: Active Cool In Progress
ListTitle = If DG active cool successfully started.
Message   = DG active cool started

[295]
Title     = HD POST: UI CloudSync
ListTitle = If the UI POST reports cloud sync failure.
Message   = UI cloud sync POST failure
 = SRSUI 1238

[296]
Title     = DG Fault: TDi RTD Comm
ListTitle = If the FPGA does not report fresh data for a certain period of time
Message   = DG TDi sensor FPGA fault
SRSDG 951 = 

[297]
Title     = DG Fault: TRo RTD Comm
ListTitle = If the FPGA does not report fresh data for a certain period of time
Message   = DG TRo sensor FPGA fault
SRSDG 950 = 

[298]
Title     = DG Fault: Baro Pres Comm
ListTitle = If the FPGA does not report fresh data for a certain period of time
Message   = DG barometric sensor FPGA fault
SRSDG 948 = 

[299]
Title     = DG POST: Serial Number Check
ListTitle = If the DG serial number is empty and does not have any characters.
Message   = DG invalid serial number
SRSDG 952 = 

[300]
Title     = HD POST: Serial Number Check
ListTitle = If the HD serial number is empty and does not have any characters.
Message   = HD invalid serial number

[301]
Title     = Cleaning: RO Permeate Sample Connect Cap
ListTitle = RO permeate sample collection state
Message   = Open dialysate cap to be able to collecte the dispensing fluid

[302]
Title     = DG Fault: Processor RAM error
ListTitle = If the RAM status indicates any of the following: Double bit error, Address decode failure, Address decode logic element failure, Read address parity failure, Write address parity failure.
Message   = DG_CPU RAM error
SRSDG 126 = 

[303]
Title     = DG Fault: DRP Hall Commutation
ListTitle = If the FPGA indicates an error for a certain period of time.
Message   = DG drain pump direction FPGA fault
SRSDG 958 = 

[304]
Title     = HD POST: Usage Rec NVRAM CRC
ListTitle = If the CRC of the HD usage record does not match the calculated CRC.
Message   = HD invalid usage reocord

[305]
Title     = HD Fault: Processor RAM error
ListTitle = If the RAM status indicates any of the following: Double bit error, Address decode failure, Address decode logic element failure, Read address parity failure, Write address parity failure.
Message   = HD_CPU RAM error

[306]
Title     = DG Fault: CD1 CD2 Check
ListTitle = CD1 and CD2 conductivity measurement during acid check is not within 5% of each other
Message   = 

[307]
Title     = Blood Stop: Loss of AC Power
ListTitle = The HD Software shall trigger an alarm if an AC power loss is detected while the HD system is in pre-treatment, treatment, or post-treatment mode.
Message   = HD AC power lost alarm

[308]
Title     = DG Fault: CPi Comm
ListTitle = If the CPi conductivity sensor transmits invalid characters for a certain period of time.
Message   = DG CPi conductivity sensor transmits invalid characters
SRSDG 959 = 

[309]
Title     = DG Fault: CPo Comm
ListTitle = If the CPo conductivity sensor transmits invalid characters for a certain period of time.
Message   = DG CPo conductivity sensor transmits invalid characters
SRSDG 960 = 

[310]
Title     = DG Fault: CD1 Comm
ListTitle = If the CD1 conductivity sensor transmits invalid characters for a certain period of time.
Message   = DG CD1 conductivity sensor transmits invalid characters
SRSDG 962 = 

[311]
Title     = DG Fault: CD2 Comm
ListTitle = If the CD2 conductivity sensor transmits invalid characters for a certain period of time.
Message   = DG CD2 conductivity sensor transmits invalid characters
SRSDG 961 = 

[312]
Title     = Dial. Gen: Dialysate In Flow
ListTitle = If the dialysate inlet flow < 10 mL/min (raw) while in treatment mode or pre-treatment mode after prime and DPi is running.
Message   = The dialysate inlet flow is too low.

[313]
Title     = Cleaning: Inlet Water Temp Low
ListTitle = If inlet water temperature is < 24 C.
Message   = DG cleaning mode inlet water temperature too low
SRSDG 1064
SRSDG 1052
SRSDG 968 = 

[314]
Title     = Cleaning: Inlet Water Press High
ListTitle = If inlet water temperature is > 80 psig.
Message   = DG cleaning mode inlet water pressure too high
SRSDG 1063
SRSDG 1051
SRSDG 967 = 

[315]
Title     = Cleaning: Inlet Water Press Low
ListTitle = If inlet water pressure is < 14 psig.
Message   = DG cleaning mode inlet water pressure too low
SRSDG 1068
SRSDG 1056
SRSDG 966 = 

[316]
Title     = DG Fault: Acid CP Pump Park
ListTitle = If the park took more than 1 second.
Message   = Acid concentrate pump did not park successfully
SRSDG 983 = 

[317]
Title     = DG Fault: Bicarb CP Pump Park
ListTitle = If the park took more than 1 second.
Message   = Bicarb concentrate pump did not park successfully
SRSDG 984 = 

[318]
Title     = HD Fault: Air Pump Timeout
ListTitle = If air pump has been turned on for greater than 10s.
Message   = HD Air Pump operation timeout

[319]
Title     = Cleaning: Chem Residual Sampling
ListTitle = Chemical disinfect flush sample alarm is prompted.
Message   = Collect sample to check the chemical disinfectant acid
SRSDG 1040 = 

[320]
Title     = Cleaning: Chem Residual Timeout
ListTitle = Chemical disinfect flush sample was not collected form more than 30 minutes.
Message   = The user did not proceed with collecting chemical disinfect flush sample for more than 30 minutes
SRSDG 1043 = 

[321]
Title     = DG Fault: UVo Error
ListTitle = If the outlet reactor are not healthy.
Message   = Outlet reactor not healthy
SRSDG 1069 = 

[322]
Title     = HD POST Alarm: UI Invalid Year
ListTitle = If the UI POST reports a invalid year.
Message   = UI POST Invalid Year

[323]
Title     = HD POST Alarm: UI Bad Settings
ListTitle = If the UI POST reports a bad settings. (e.g. no settings read, empty settings file, invalid/empty parms, CRC failure)
Message   = UI POST Bad Settings