Index: AlarmMapping.csv =================================================================== diff -u -rb3a919eb1696079530d537fb2bf8b7e526178997 -r5b46bc8e4724e4ddb648f901d76bb7ec24f8b6c7 --- AlarmMapping.csv (.../AlarmMapping.csv) (revision b3a919eb1696079530d537fb2bf8b7e526178997) +++ AlarmMapping.csv (.../AlarmMapping.csv) (revision 5b46bc8e4724e4ddb648f901d76bb7ec24f8b6c7) @@ -41,14 +41,14 @@ 40,"Dialysis outlet pump failed motor off check.\nMeasured speed while commanded off." 41,"Dialysis outlet pump failed motor direction check.\nMeasured vs commanded." 42,"Dialysis outlet pump failed rotor speed check.\nMismatch with rotor and motor speeds." - 43,"HD blood leak self test fault." + 43,"DG main primary heater FPGA fault." 44,"User interface communication timeout." 45,"HD too many bad communications CRC." - 46,"System message that required acknowledgment was not acknowledged." + 46,"HD System message that required acknowledgment was not acknowledged." 47,"Ultrafiltration rate is too high error during treatment." 48,"Ultrafiltration volume accuracy error during treatment." 49,"HD FPGA communication down for too long." - 50,"FPGA not accepting commanded valve states." + 50,"DG FPGA not accepting commanded valve states." 51,"Blood pump failed motor speed check.\nMeasured vs commanded." 52,"Dialysate inlet pump failed motor speed check.\nMeasured vs commanded." 53,"Dialysate outlet pump failed motor speed check.\nMeasured vs commanded." @@ -61,8 +61,8 @@ 60,"HD valve not functional." 61,"HD valve current out of range." 62,"HD valve position out of target." - 63,"FPGA reports failure reading arterial pressure sensor." - 64,"FPGA reports failure reading venous pressure sensor." + 63,"HD blood leak FPGA fault." + 64,"DG barometric pressure sensor out of range." 65,"HD requests DG command with invalid parameter fault." 66,"HD blood leak sensor set point set failure." 67,"HD blood pump occlusion self-test failure alarm." @@ -72,7 +72,7 @@ 71,"HD venous pressure self-test failure alarm." 72,"HD No load cell data message receive at least once every 2 seconds." 73,"HD No dialysate temperature data message receive at least once every 2 seconds." - 74,"HD blood leak detector self-test transmit timeout." + 74,"DG inlet UV reactor is on with no flow." 75,"HD syringe pump self-test failure alarm." 76,"HD monitored voltage is out of range." 77,"DG monitored voltage is out of range." @@ -82,13 +82,13 @@ 81,"HD syringe pump over travel error." 82,"HD syringe pump DAC write failure." 83,"HD syringe pump is running while the BP is off." - 84,"HD venous pressure sensor not being read." + 84,"DG set RTC year is invalid." 85,"HD pump track latch opened alarm." - 86,"HD BP occlusion sensor not being read." + 86,"HD set RTC year is invalid." 87,"DG heating invalid calibration record." 88,"DG concentrate pumps hall sensor out of range." - 89,"HD BP occlusion sensor error." - 90,"DG load cells FPGA read error." + 89,"DG outlet UV reactor on with no flow." + 90,"DG load cells A1/B1 FPGA fault." 91,"HD No dialysate flow data receive in the last 3 seconds." 92,"DG conductivity sensor bad status." 93,"DG outlet primary conductivity out of range." @@ -106,12 +106,12 @@ 105,"DG invalid calibration CRC." 106,"DG dialysate flow sensor invalid calibration record." 107,"HD reports DG restarted fault." - 108,"HD syringe pump ADC error." + 108,"HD syringe pump ADC FPGA fault." 109,"HD syringe pump volume check error." 110,"HD syringe pump speed check error." 111,"HD syringe pump not stopped in off state error." - 112,"HD blood leak zero command transmit timeout." - 113,"HD blood leak zero command fault." + 112,"DG load cells A1/B1 FPGA fault." + 113,"DG Drain pump current out of range." 114,"HD venous air bubble detector self-test failure." 115,"DG temperature sensor out of range." 116,"DG temperature sensor ADC fault." @@ -142,22 +142,22 @@ 141,"Air trap fill timeout during treatment." 142,"Blood pump occlusion detected." 143,"DG dialysate temperature sensors out of range." - 144,"DG RO flow sensor invalid calibration record." + 144,"DG cleaning mode inlet water conductivity out of high range." 145,"Concentrate conductivity after adding acid out of range alarm." 146,"DG RTC or timer accuracy failure." 147,"Wait for the DG to produce dialysate." - 148,"Inlet water temperature too high." + 148,"DG Cleaning mode inlet water temperature too high." 149,"HD watchdog expired." 150,"Inlet water conductivity in high range." 151,"Inlet water conductivity in low range." 152,"Inlet water pressure in low range." 153,"HD prime completed high priority alarm." - 154,"EEPROM operations (read, write, erase) failure." + 154,"DG cleaning mode inlet water conductivity out of low range." 155,"HD No reservoirs data message receive at least once every 2 seconds." 156,"HD No DG operation mode message receive at least once every 2 seconds." 157,"DG chemical disinfect prime acid line timeout." 158,"Inlet water temperature is in the low range." - 159,"Dialysate inlet pump failed flow vs motor speed check." + 159,"DG chemical disinfect flush remove acid and close the concentrate cap." 160,"Blood pump rotor speed too high." 161,"DG comm too many bad CRCs." 162,"DG FPGA clock speed check failure." @@ -167,7 +167,7 @@ 166,"HD in treatment re-circ sub-mode for too long." 167,"HD cartridge door opened alarm." 168,"HD active reservoir depletion timeout." - 169,"Dialysate flow rate out of range." + 169,"DG Dialysate flow rate out of maximum range." 170,"HD syringe empty alarm." 171,"HD syringe pump occlusion alarm." 172,"HD syringe pump not enough Heparin alarm." @@ -178,7 +178,7 @@ 177,"DG software fault.\nSoftware found itself in an unexpected state." 178,"HD communication timeout." 179,"DG FPGA communication down for too long." - 180,"DG load cell ADC error." + 180,"DG RO flow out of maximum range." 181,"DG load cells weight out of range for tare." 182,"DG load cells invalid calibration." 183,"DG invalid load cell value." @@ -194,8 +194,8 @@ 193,"HD dialysate temperature out of low safety range." 194,"DG RO pump duty cycle out of range." 195,"DG RO pump pressure out of range." - 196,"DG temperature sensor error bit fault." - 197,"DG temperature sensors FPGA fault." + 196,"DG CPi/CPo sensors FPGA fault." + 197,"DG CD1/CD2 sensors FPGA fault." 198,"RO flow too low while primary heater is on." 199,"Dialysate flow too low while trimmer heater is on." 200,"DG thermistors/sensors temperature out of range." @@ -220,8 +220,8 @@ 219,"HD syringe pump syringe removed alarm." 220,"DG THd sensors FPGA fault." 221,"HD Saline bag is empty." - 222,"HD dialysate temperature too high alarm." - 223,"HD dialysate temperature too low alarm." + 222,"HD occlusion sensor FPGA fault." + 223,"HD arterial sensor FPGA fault." 224,"Treatment stopped by user action." 225,"HD end of treatment warning." 226,"HD prime completed low priority alarm." @@ -232,7 +232,7 @@ 231,"HD pre-treatment mode dry pressure self-test failure." 232,"HD pre-treatment mode wet self-test LC vs LC failure." 233,"DG barometric sensor coefficients bad CRC." - 234,"RTC (i.e read time) or RAM operations failure (read or write)." + 234,"DG inlet water pressure in high range." 235,"HD in treatment stopped sub-mode after rinseback completed (no escalation)." 236,"HD needs new cartridge to be installed." 237,"HD prime saline dialyzer time out alarm." @@ -242,13 +242,13 @@ 241,"DG reservoir drain time out." 242,"DG reservoir fill time out." 243,"DG reservoir leak time out." - 244,"DG temperature sensors difference out of range." + 244,"DG cleaning mode temperature sensors difference out of range." 245,"DG heat disinfect target temperature time out (could not reach to temperature)." - 246,"DG heat disinfect inlet pressure and temperature sensors out of range." - 247,"DG heat disinfect inlet conductivity and temperature out of range." - 248,"DG chemical disinfect could not reach to target temperature." - 249,"DG chemical disinfect inlet pressure and temperature sensors out of range." - 250,"DG chemical disinfect inlet conductivity and temperature out of range." + 246,"DG cleaning mode conductivity sensors out of range." + 247,"DG heat disinfect active cool time tour." + 248,"DG chemical disinfect could not reach to target temperature out of range." + 249,"DG chemical disinfect target conductivity out of range." + 250,"DG chemical disinfect insert acid and remove the concentrate cap." 251,"HD invalid system record." 252,"HD invalid service record." 253,"DG invalid system record." @@ -278,7 +278,7 @@ 277,"HD BP occlusion sensor is reading out of range." 278,"HD active reservoir weight out of range." 279,"DG dialysate drain time out." - 280,"HD arterial pressure sensor read timeout error." + 280,"DG drain pump direction invalid." 281,"Acid concentration bottle low volume alarm." 282,"Bicarbonate concentration bottle low volume alarm." 283,"DG load cells weight out of range." @@ -288,7 +288,7 @@ 287,"HD processor clock speed checks against FPGA clock failure." 288,"HD load cells primary/back up drift out of range." 289,"DG dialysate or concentrate caps not closed." - 290,"DG flow too low while heater is on." + 290,"HD venous pressure sensor FPGA fault." 291,"HD processor is in Disinfect Flush mode." 292,"HD processor is in Disinfect Heat mode." 293,"HD processor is in Disinfect Chemical mode." @@ -297,8 +297,26 @@ 296,"DG TDi sensors FPGA fault." 297,"DG TRo sensors FPGA fault." 298,"DG baro sensor FPGA fault." - 299,"DG disinfect has been expired." - 300,"DG service time interval has elapsed." + 299,"DG invalid serial number." + 300,"HD invalid serial number." 301,"DG primary heater power voltage out of range." 302,"DG processor RAM error." - 303,"Total number of alarms." + 303,"DG drain pump direction FPGA fault." + 304,"HD invalid usage record." + 305,"HD processor RAM error." + 306,"HD air trap over-fill alarm." + 307,"HD AC power lost second alarm." + 308,"DG CPi conductivity sensor invalid character received." + 309,"DG CPo conductivity sensor invalid character received." + 310,"DG CD1 conductivity sensor invalid character received." + 311,"DG CD2 conductivity sensor invalid character received." + 312,"HD Dialysate In flow rate to too low." + 313,"DG cleaning mode inlet water temperature too low." + 314,"DG cleaning mode inlet water pressure too high." + 315,"DG cleaning mode inlet water pressure too low." + 316,"DG acid concentrate pump park fault." + 317,"DG bicarb concentrate pump part fault." + 318,"HD Air Pump timeout alarm." + 319,"DG chemical disinfect flush flush sample." + 320,"DG chemical disinfect flush sample timeout." + 321,"Total number of alarms."