Index: AlarmDefs.h
===================================================================
diff -u -r819fddd8934072f7ea8a775f21c6d0ce745493a1 -rb9bc64762582f83b5aaeb4dc3277cff2c7aebc40
--- AlarmDefs.h	(.../AlarmDefs.h)	(revision 819fddd8934072f7ea8a775f21c6d0ce745493a1)
+++ AlarmDefs.h	(.../AlarmDefs.h)	(revision b9bc64762582f83b5aaeb4dc3277cff2c7aebc40)
@@ -1479,7 +1479,7 @@
  { 312 , ALARM_ID_HD_DIAL_IN_FLOW_CHECK_FAILURE                        , "HD    | Low Dialysate Flow                      | Dialysate flow rate is low. \n- Confirm dialysate concentrate connections are secure. \n- When the flow rates are within target range \nResume/OK button will be available.\n- Press Resume/OK to continue.                                                                                                                     | Dial. Gen: Dialysate In Flow             | The dialysate inlet flow is too low.                                                                                                      | If the dialysate inlet flow < 10 mL/min (raw) while in treatment mode or pre-treatment mode after prime and DPi is running.                                                                                                                                                      | "},
  { 313 , ALARM_ID_DG_CLEANING_MODE_INLET_WATER_TEMP_TOO_LOW            , "DG    | Disinfection: Water Temperature Low     | Incoming water temperature is too low.\n- Disinfection has been terminated.\n- Check incoming water before initiating disinfection again.                                                                                                                                                                                       | Cleaning: Inlet Water Temp Low           | DG cleaning mode inlet water temperature too low                                                                                          | If inlet water temperature is < 24 C.                                                                                                                                                                                                                                            | "},
  { 314 , ALARM_ID_DG_CLEANING_MODE_INLET_WATER_PRESSURE_TOO_HIGH       , "DG    | Disinfection: Water Pressure High       | Incoming water pressure is too high. \n- Disinfection has been terminated.\n- Check incoming water before initiating disinfection again.                                                                                                                                                                                        | Cleaning: Inlet Water Press High         | DG cleaning mode inlet water pressure too high                                                                                            | If inlet water temperature is > 80 psig.                                                                                                                                                                                                                                         | "},
- { 315 , ALARM_ID_DG_CLEANING_MODE_INLET_WATER_PRESSURE_TOO_LOW        , "DG    | Disinfection: Water Pressure Low        | Incoming water pressure is too low. \n- Disinfection has been terminated.\n- Check incoming water pressure before initiating disinfection again.                                                                                                                                                                                                | Cleaning: Inlet Water Press Low          | DG cleaning mode inlet water pressure too low                                                                                             | If inlet water pressure is < 14 psig.                                                                                                                                                                                                                                            | "},
+ { 315 , ALARM_ID_DG_CLEANING_MODE_INLET_WATER_PRESSURE_TOO_LOW        , "DG    | Disinfection: Water Pressure Low        | Incoming water pressure is too low. \n- Disinfection has been terminated.\n- Check incoming water pressure before initiating disinfection again.                                                                                                                                                                                | Cleaning: Inlet Water Press Low          | DG cleaning mode inlet water pressure too low                                                                                             | If inlet water pressure is < 14 psig.                                                                                                                                                                                                                                            | "},
  { 316 , ALARM_ID_DG_ACID_CONCENTRATE_PUMP_PARK_FAULT                  , "DG    | Service Required: Dialysate Device      | A problem was detected with the dialysate device. \n- Treatment must be terminated.\n- Locate the ID code found in the bottom left corner\nof the alarm screen.\n- Call service to report the issue and schedule a repair.                                                                                                      | DG Fault: Acid CP Pump Park              | Acid concentrate pump did not park successfully                                                                                           | If the park took more than 1 second.                                                                                                                                                                                                                                             | "},
  { 317 , ALARM_ID_DG_BICARB_CONCENTRATE_PUMP_PARK_FAULT                , "DG    | Service Required: Dialysate Device      | A problem was detected with the dialysate device. \n- Treatment must be terminated.\n- Locate the ID code found in the bottom left corner\nof the alarm screen.\n- Call service to report the issue and schedule a repair.                                                                                                      | DG Fault: Bicarb CP Pump Park            | Bicarb concentrate pump did not park successfully                                                                                         | If the park took more than 1 second.                                                                                                                                                                                                                                             | "},
  { 318 , ALARM_ID_HD_AIR_PUMP_TIMEOUT                                  , "HD    | Air Trap Control Error                  | A problem has been detected with the air trap level\ncontrol system.\n- Treatment must be terminated.\n- Locate the ID code found in the bottom left corner\nof the alarm screen.\n- Call service to report the issue.                                                                                                          | HD Fault: Air Pump Timeout               | HD Air Pump operation timeout                                                                                                             | If air pump has been turned on for greater than 10s.                                                                                                                                                                                                                             | "},