Index: AlarmDefs.h
===================================================================
diff -u -re9beb6b7cbe88dfd9c38ef0ca9f4724ca28916a3 -rcdde55b1e1af5712de18cc908b2b2f2ab6588527
--- AlarmDefs.h	(.../AlarmDefs.h)	(revision e9beb6b7cbe88dfd9c38ef0ca9f4724ca28916a3)
+++ AlarmDefs.h	(.../AlarmDefs.h)	(revision cdde55b1e1af5712de18cc908b2b2f2ab6588527)
@@ -1396,7 +1396,7 @@
  { 235 , ALARM_ID_HD_TREATMENT_STOPPED_AFTER_RINSEBACK                 , "HD    | Rinseback Complete                      | Rinseback is complete. \n- Follow facililty policy prior to disconnecting patient. \n- Press OK to continue. \n\nProcess: Rinseback Complete                                                                                                                                                                                                                         | HD in treatment stopped sub-mode after rinseback completed (no escalation)                                                                | If there is no active alarm and rinseback has completed.                                                                                                                                                                                                                         | "},
  { 236 , ALARM_ID_HD_INSTALL_NEW_CARTRIDGE                             , "HD    | Self Test: Fluid Present                | A problem has been detected during self- test.  \n- Cartridges are single- use only and fluid is present.\n- Install new cartridge to resume.\n\nProcess: Pre- Tx Dry Self- Test                                                                                                                                                                                     | HD needs new cartridge to be installed                                                                                                    | If the air trap sensor reported AIR and bubble sensor detected bubbles.                                                                                                                                                                                                          | "},
  { 237 , ALARM_ID_HD_PRIME_SALINE_DIALYZER_TIME_OUT                    , "HD    | Priming Error                           | A problem has been detected during prime. \n- Prime was unable to complete. \n - Check blood and dialysate lines for clamps, kinks or leaks. \n\nProcess: Pre- Tx Prime Timeout                                                                                                                                                                                      | HD prime saline dialyzer time out alarm                                                                                                   | If timeout, just transition to HD_PRIME_RESERVOIR_TWO_FILL_COMPLETE_STATE                                                                                                                                                                                                        | "},
- { 238 , ALARM_ID_HD_NO_CARTRIDGE_LOADED                               , "HD    | Cartridge Not Dectected                 | A problem has been detected during self- test. \n- Cartridge is not detected.\n- Confirm cartridge is properly installed.\n\nProcess: Pre- Tx Dry Self- Test                                                                                                                                                                                                         | HD no cartridge loaded or installed improperly alarm                                                                                      | If the measured blood pump occlucsion pressure reading is < 5000 or > 24500.                                                                                                                                                                                                     | "},
+ { 238 , ALARM_ID_HD_NO_CARTRIDGE_LOADED                               , "HD    | Cartridge Not Detected                  | A problem has been detected during self- test. \n- Cartridge is not detected.\n- Confirm cartridge is properly installed.\n\nProcess: Pre- Tx Dry Self- Test                                                                                                                                                                                                         | HD no cartridge loaded or installed improperly alarm                                                                                      | If the measured blood pump occlucsion pressure reading is < 5000 or > 24500.                                                                                                                                                                                                     | "},
  { 239 , ALARM_ID_HD_CARTRIDGE_REMOVAL_FAILURE                         , "HD    | Cartridge Still Detected                | A problem has been detected during self- test. \n- Cartridge is still present or was unloaded incorrectly.\n- Confirm the cartridge has been fully removed.\n\nProcess: Post- Tx Remove Cartridge                                                                                                                                                                    | HD fail to remove cartridge alarm                                                                                                         | In the post treatment state, if the cartridge has not been removed.                                                                                                                                                                                                              | "},
  { 240 , ALARM_ID_DG_BICARB_CONDUCTIVITY_OUT_OF_RANGE                  , "DG    | Conductivity Error During Prime         | Conductivity out of range during prime.\n- Confirm that acid and bicarbonate concentrates\nare securely connected.\n- If empty, replace. \n- Treatment will need to be resumed when conductivity\nis within target range.\n\nDial. Gen: Bicarb Conc. Cond.                                                                                                           | Bicarb conductivity out of range during bicarb pump check alarm                                                                           | If the conductivity value for bicarbonate concentrate is out of range for more than 45 secs.                                                                                                                                                                                     | "},
  { 241 , ALARM_ID_DG_RESERVOIR_DRAIN_TIMEOUT                           , "DG    | Disinfection Interrupted                | Dinsinfection terminated unexpectedly.\n- Restart disinfection.\n- If problem persists, call service to schedule a repair.\n\nCleaning: Resv Drain Timeout                                                                                                                                                                                                           | DG reservoir drain time out                                                                                                               | If the DG reservoir drain is not complete in 120 secs.                                                                                                                                                                                                                           | "},