Index: AlarmDefs.h
===================================================================
diff -u -r1d702021ecc4d4cfbc487f8904212001c6070f80 -r6db5724424b780b1bbcc297b6389a7f077324ef3
--- AlarmDefs.h	(.../AlarmDefs.h)	(revision 1d702021ecc4d4cfbc487f8904212001c6070f80)
+++ AlarmDefs.h	(.../AlarmDefs.h)	(revision 6db5724424b780b1bbcc297b6389a7f077324ef3)
@@ -1254,7 +1254,7 @@
  { 93  , ALARM_ID_DG_OUTLET_PRIMARY_CONDUCTIVITY_OUT_OF_RANGE          , "DG    | Service Required: Dialysate Device      | A problem was detected with the dialysate device. \n- Treatment must be terminated.\n- Locate the ID code found in the bottom left corner\nof the alarm screen.\n- Call service to report the issue and schedule a repair.                                                                                                      | DG Fault: RO Permeate Cond High          | DG outlet primary conductivity sensor out of range                                                                                        | If the outlet primary conductivity sensor, CPo is greater than 30 uS/cm for a certain period of time.                                                                                                                                                                            | "},
  { 94  , ALARM_ID_DG_PRESSURE_OUT_OF_RANGE                             , "DG    | Service Required: Dialysate Device      | A problem was detected with the dialysate device. \n- Treatment must be terminated.\n- Locate the ID code found in the bottom left corner\nof the alarm screen.\n- Call service to report the issue and schedule a repair.                                                                                                      | DG Fault: Pressure Sensor Range          | DG pressure sensor out of range                                                                                                           | If either of the pressure sensors is < 0 psia or > 200 psia for DG pressure sensors.                                                                                                                                                                                             | "},
  { 95  , ALARM_ID_DG_WATCHDOG_EXPIRED                                  , "DG    | Service Required: Dialysate Device      | A problem was detected with the dialysate device. \n- Treatment must be terminated.\n- Locate the ID code found in the bottom left corner\nof the alarm screen.\n- Call service to report the issue and schedule a repair.                                                                                                      | DG Fault: WD Error                       | DG watchdog expired                                                                                                                       | If the watchdog signal is low while not in POST.                                                                                                                                                                                                                                 | "},
- { 96  , ALARM_ID_DG_INLET_WATER_TEMPERATURE_IN_HIGH_RANGE             , "DG    | Incoming Water Temperature High         | Incoming water temperature is high.\n- Treatment is currently paused.\n- Check the incoming water supply.\n- When the temperature is within target range\nRsume/OK button will be available.\n- Press Resume/OK to continue treatment.                                                                                          | Dial. Gen: Inlet Water Temp High         | DG inlet water temperature out of range                                                                                                   | If the inlet water temperature is > 37 C.                                                                                                                                                                                                                                        | "},
+ { 96  , ALARM_ID_DG_INLET_WATER_TEMPERATURE_IN_HIGH_RANGE             , "DG    | Incoming Water Temperature High         | Incoming water temperature is high.\n- Treatment is currently paused.\n- Check the incoming water supply.\n- When the temperature is within target range\nResume/OK button will be available.\n- Press Resume/OK to continue treatment.                                                                                         | Dial. Gen: Inlet Water Temp High         | DG inlet water temperature out of range                                                                                                   | If the inlet water temperature is > 37 C.                                                                                                                                                                                                                                        | "},
  { 97  , ALARM_ID_DG_FILL_CONDUCTIVITY_OUT_OF_RANGE                    , "DG    | Conductivity Out of Range               | Treatment is currently paused.\n- Confirm that acid and bicarbonate concentrates\nare securely connected.\n- If empty, replace. \n- Treatment will need to be resumed when conductivity\nis within target range.                                                                                                                | Dial. Gen: Dialysate Cond.               | DG fill conductivity out of range                                                                                                         | If the average acid or bicard conductivity is > 5% of the normal acid and bicarb conductivity values.                                                                                                                                                                            | "},
  { 98  , ALARM_ID_HD_BATTERY_COMM_FAULT                                , "HD    | Service Required: Hemodialysis Device   | A non- critical problem was detected with the hemodialysis\n device.\n- Call service to report the issue and schedule a repair.                                                                                                                                                                                                 | HD Alarm (Low): Battery Com              | HD battery or battery charger communication fault                                                                                         | If battery I2C communication fault persistence count > 5.                                                                                                                                                                                                                        | "},
  { 99  , ALARM_ID_HD_SYRINGE_PUMP_STALL                                , "HD    | Service Required: Hemodialysis Device   | A problem was detected with the hemodialysis device. \n- Treatment must be terminated.\n- Locate the ID code found in the bottom left corner\nof the alarm screen.\n- Call service to report the issue and schedule a repair.                                                                                                   | HD Fault: Syringe Pump Stall             | HD syringe pump stall alarm                                                                                                               | If syringe pump measured rate < stall speed threshold (0.05) and the ramp up has been restarted 3 times after stall has been detected.                                                                                                                                           | "},