Index: firmware/App/Modes/ModeGenDialysate.c
===================================================================
diff -u -ra6737c3bcc8286c153b778c2c395f465e76aaafb -rdc451e960ab328d05a06137ffdc4d8b2b1601d55
--- firmware/App/Modes/ModeGenDialysate.c	(.../ModeGenDialysate.c)	(revision a6737c3bcc8286c153b778c2c395f465e76aaafb)
+++ firmware/App/Modes/ModeGenDialysate.c	(.../ModeGenDialysate.c)	(revision dc451e960ab328d05a06137ffdc4d8b2b1601d55)
@@ -61,11 +61,11 @@
 #define ZERO_DIAL_FLOW_RATE                             0.0F                                        ///< Zero dialysate flow rate
 #define SPENT_CHAMBER_FILL_MAX_COUNT                    10                                          ///< Total number of spent chamber fill allowed.
 #define BICARB_CHAMBER_FILL_TIMEOUT                     ( 1 * MS_PER_SECOND )                       ///< Bicarb chamber fill timeout.
-
 #define PUMP_SPEED_SLOPE_FACTOR_DIENER_2000             1.24F                                       ///< D48 Diener 2000 pump speed slope (y = 1.24x + 30).
 #define PUMP_SPEED_INTERCEPT_FACTOR_DIENER_2000         30.0F                                       ///< D48 Diener 2000 pump speed intercept.
 #define PUMP_SPEED_SLOPE_FACTOR_DIENER_1000             2.869F                                      ///< D48 Diener 1000 pump speed slope (y = 2.869x + 25.956).
 #define PUMP_SPEED_INTERCEPT_FACTOR_DIENER_1000         25.956F                                     ///< D48 Diener 1000 pump speed intercept.
+
 #define BICARB_CHAMBER_FILL_TIMEOUT                     ( 1 * MS_PER_SECOND )                       ///< Bicarb chamber fill timeout.
 
 //Testing
@@ -270,7 +270,7 @@
             startHeater( D5_HEAT );
 
             //Turn on Trimmer heater
-            if ( getTestConfigStatus( TEST_CONFIG_DD_FP_ENABLE_BETA_1_0_HW ) == TRUE )
+            if ( TRUE == getTestConfigStatus( TEST_CONFIG_DD_FP_ENABLE_BETA_1_0_HW ) )
             {
                 setHeaterTargetTemperature( D45_HEAT, getFilteredTemperatureValue( D4_TEMP ) );
             }
@@ -319,7 +319,7 @@
             startHeater( D5_HEAT );
 
             //Turn on Trimmer heater
-            if ( getTestConfigStatus( TEST_CONFIG_DD_FP_ENABLE_BETA_1_0_HW ) == TRUE )
+            if ( TRUE == getTestConfigStatus( TEST_CONFIG_DD_FP_ENABLE_BETA_1_0_HW ) )
             {
                 setHeaterTargetTemperature( D45_HEAT, getFilteredTemperatureValue( D4_TEMP ) );
             }
@@ -1022,8 +1022,6 @@
         // Get the target temperature from TD
         //targetHydChamberFluidTemp.data = getTDTargetDialysateTemperature();
         calculateTargetDialysateTemp();
-        //Reset flag
-        signaltoResetPrimaryHeaterAdjustedTargetTemp();
 
         // Update the target temperature for heater control
         setHeaterTargetTemperature( D5_HEAT, getGenDialysateTargetTemperature() );