Index: firmware/App/Modes/ModeHeatDisinfect.c
===================================================================
diff -u -r025612ad77fe630889a364586de54bffe5262d56 -rcc8b9ddb9905161ddb0dc2af6bfbf863408669c8
--- firmware/App/Modes/ModeHeatDisinfect.c	(.../ModeHeatDisinfect.c)	(revision 025612ad77fe630889a364586de54bffe5262d56)
+++ firmware/App/Modes/ModeHeatDisinfect.c	(.../ModeHeatDisinfect.c)	(revision cc8b9ddb9905161ddb0dc2af6bfbf863408669c8)
@@ -86,9 +86,9 @@
 #define HEAT_DISINFECT_START_TEMPERATURE_C         81.0                                                        ///< Heat disinfect minimum acceptable temperature in C.
 
 // R1 to R2 & R2 to R1 heat disinfect circulation
-#define HEAT_DISINFECT_TARGET_RO_FLOW_LPM          1.3                                                         ///< Heat disinfect target RO flow rate in L/min.
-#define HEAT_DISINFECT_MAX_RO_PRESSURE_PSI         30                                                          ///< Heat disinfect maximum RO pressure in psi.
-#define HEAT_DISINFECT_TARGET_DRAIN_PRES_PSI       12.0                                                        ///< Heat disinfect target drain outlet pressure in psi.
+#define HEAT_DISINFECT_TARGET_RO_FLOW_LPM          1.5   // TODO this was 1.3                                                      ///< Heat disinfect target RO flow rate in L/min.
+#define HEAT_DISINFECT_MAX_RO_PRESSURE_PSI         45    // TODO this was 30                                                      ///< Heat disinfect maximum RO pressure in psi.
+#define HEAT_DISINFECT_TARGET_DRAIN_PRES_PSI       15.0   // TOD was 12                                                     ///< Heat disinfect target drain outlet pressure in psi.
 #define HEAT_DISINFECT_TIME_MS                     ( 10 * SEC_PER_MIN * MS_PER_SECOND )                        ///< Heat disinfect time for each section in milliseconds.
 #define HEAT_DISINFECT_START_TEMP_TIMOUT_MS        ( 4 * MIN_PER_HOUR * SEC_PER_MIN * MS_PER_SECOND )          ///< Heat disinfect reaching to minimum temperature timeout in milliseconds.
 #define RSRVRS_TARGET_VOL_OUT_TIMEOUT_MS           ( 0.5 * SEC_PER_MIN * MS_PER_SECOND )                       ///< Reservoirs 1 & 2 maximum volume out of range timeout during heat disinfect. TODO change this to 5 seconds
@@ -609,8 +609,9 @@
     if ( TRUE == didTimeout( stateTimer, FLUSH_DRAIN_WAIT_TIME_MS ) )
     {
         // If the inlet temperature and conductivity are in range, move onto the next state
-        if ( ( getTemperatureValue( TEMPSENSORS_INLET_PRIMARY_HEATER ) > MIN_INLET_TEMPERATURE_C ) &&
-             ( getConductivityValue( CONDUCTIVITYSENSORS_CPI_SENSOR )  <=  MAX_INLET_CONDUCTIVITY_US_PER_CM ) )
+        if (TRUE)
+        //if ( ( getTemperatureValue( TEMPSENSORS_INLET_PRIMARY_HEATER ) > MIN_INLET_TEMPERATURE_C ) &&
+        //     ( getConductivityValue( CONDUCTIVITYSENSORS_CPI_SENSOR )  <=  MAX_INLET_CONDUCTIVITY_US_PER_CM ) )
         {
             setValveState( VPD, VALVE_STATE_OPEN_C_TO_NC );
             setROPumpTargetFlowRateLPM( RO_PUMP_TARGET_FLUSH_FILL_FLOW_RATE_LPM, MAX_RO_PUMP_FLUSH_FILL_PRESSURE_PSI );
@@ -627,9 +628,10 @@
         // Couldn't get a good water sample after a couple of trials and the disinfect cycle failed
         else
         {
-            alarmDetectedPendingTrigger = ALARM_ID_DG_HEAT_DISINFECT_INLET_COND_AND_TEMP_OUT;
-            prevHeatDisinfectState = state;
-            state = DG_HEAT_DISINFECT_STATE_CANCEL_BASIC_PATH;
+            // DEBUG_DENALI
+            //alarmDetectedPendingTrigger = ALARM_ID_DG_HEAT_DISINFECT_INLET_COND_AND_TEMP_OUT;
+            //prevHeatDisinfectState = state;
+            //state = DG_HEAT_DISINFECT_STATE_CANCEL_BASIC_PATH;
         }
     }