Index: firmware/App/Controllers/DialInFlow.c
===================================================================
diff -u -r4c5ab126c8c33f9a5dcc58cef8933bbe0b1c25b4 -r270b4665c25617158ef06c1819debfb5bd59a942
--- firmware/App/Controllers/DialInFlow.c	(.../DialInFlow.c)	(revision 4c5ab126c8c33f9a5dcc58cef8933bbe0b1c25b4)
+++ firmware/App/Controllers/DialInFlow.c	(.../DialInFlow.c)	(revision 270b4665c25617158ef06c1819debfb5bd59a942)
@@ -50,7 +50,7 @@
 #define MAX_DIAL_IN_PUMP_PWM_STEP_DN_CHANGE  0.02F           ///< Max duty cycle change when ramping down ~ 300 mL/min/s.
 #define MAX_DIAL_IN_PUMP_PWM_DUTY_CYCLE      0.90F           ///< Controller will error if PWM duty cycle > 90%, so set max to 90%.
 #define MIN_DIAL_IN_PUMP_PWM_DUTY_CYCLE      0.10F           ///< Controller will error if PWM duty cycle < 10%, so set min to 10%.
-#define MIN_DG_DIAL_FLOW_RATE                10.0F           ///< Minimum DG Dialysate Flow Rate (mL/Min) - DN-9NOV2022
+#define MIN_DG_DIAL_FLOW_RATE                10.0F           ///< Minimum DG Dialysate Flow Rate (mL/Min)
 
 #define DIP_CONTROL_INTERVAL_SEC             4               ///< Dialysate inlet pump control interval (in seconds).
 /// Interval (ms/task time) at which the dialIn pump is controlled.
@@ -74,7 +74,7 @@
 #define DIP_MAX_MOTOR_SPEED_VS_TRGT_DIFF_PCT 0.15F           ///< Maximum motor speed vs target difference in percent.
 
 /// Persist time (task intervals) for unexpected flow check failure condition.
-static const U32 DIP_UNEXP_FLOW_CHK_PERSIST    = ((5 * MS_PER_SECOND) / TASK_PRIORITY_INTERVAL);
+static const U32 DIP_NO_FLOW_CHK_PERSIST       = ((10 * MS_PER_SECOND) / TASK_PRIORITY_INTERVAL);
 /// Persist time (task intervals) for motor off error condition.
 static const U32 DIP_OFF_ERROR_PERSIST         = ((5 * MS_PER_SECOND) / TASK_PRIORITY_INTERVAL);
 /// Persist time (task intervals) motor speed error condition.
@@ -276,7 +276,7 @@
 
     // Initialize persistent alarm for flow sensor signal strength too low
     initPersistentAlarm( ALARM_ID_HD_DIAL_IN_FLOW_OUT_OF_RANGE, 0, DIP_MAX_FLOW_RATE_OUT_OF_RANGE_PERSIST );
-    initPersistentAlarm( ALARM_ID_HD_DIAL_IN_FLOW_CHECK_FAILURE, DIP_UNEXP_FLOW_CHK_PERSIST, DIP_UNEXP_FLOW_CHK_PERSIST );
+    initPersistentAlarm( ALARM_ID_HD_DIAL_IN_FLOW_CHECK_FAILURE, 0, DIP_NO_FLOW_CHK_PERSIST );
     initTimeWindowedCount( TIME_WINDOWED_COUNT_DIP_COMMUTATION_ERROR, DIP_COMMUTATION_ERROR_MAX_CNT, DIP_COMMUTATION_ERROR_TIME_WIN_MS );
 }
 
@@ -1414,10 +1414,9 @@
     }
 
     // Check DG Dialysate flow rate
-    /* TODO: Temporarily comment this out. Will restore it when know better how to handle this alarm.
     if ( ( TRUE == isDialInPumpRunning() ) && ( dialInPumpControlMode != PUMP_CONTROL_MODE_OPEN_LOOP ) )
     {
-        F32 measuredDialInFlow = getDGDialysateFlowRateLMin() * ML_PER_LITER;
+        F32 measuredDialInFlow = getDGRawDialysateFlowRateLMin() * ML_PER_LITER;
 
         if ( ( TRUE == isPersistentAlarmTriggered( ALARM_ID_HD_DIAL_IN_FLOW_CHECK_FAILURE, measuredDialInFlow <  MIN_DG_DIAL_FLOW_RATE ) ) )
         {
@@ -1427,7 +1426,7 @@
     else
     {
         isPersistentAlarmTriggered( ALARM_ID_HD_DIAL_IN_FLOW_CHECK_FAILURE, FALSE );
-    }    */
+    }
 }
 
 /*********************************************************************//**