Index: firmware/App/HDCommon.h
===================================================================
diff -u -r6c34ce9c95ba654ebb9f880bf35b7e8c594184f1 -r29cb4f24819fd6590283fd5312bd373c6f0b7bd8
--- firmware/App/HDCommon.h	(.../HDCommon.h)	(revision 6c34ce9c95ba654ebb9f880bf35b7e8c594184f1)
+++ firmware/App/HDCommon.h	(.../HDCommon.h)	(revision 29cb4f24819fd6590283fd5312bd373c6f0b7bd8)
@@ -43,18 +43,18 @@
     #define DISABLE_AIR_TRAP_LEVELING       1           // Disable air trap level control
 //    #define DISABLE_3WAY_VALVES             1           // Disable 3-way valves
 //    #define TST_3WAY_VALVES_ALWAYS_OPEN     1           // After POST and homing, open all 4 valves
-//    #define DISABLE_ACCELS                  1           // Disable accelerometer POST and monitoring
+    #define DISABLE_ACCELS                  1           // Disable accelerometer POST and monitoring
 //    #define DISABLE_CRC_ERROR               1           // Do not error on bad CRC for CAN messages
 //    #define DISABLE_ACK_ERRORS              1           // Do not error on failure of other node(s) to ACK a message
     #define DISABLE_MOTOR_CURRENT_CHECKS    1           // Do not error on HD pump current checks
     #define DISABLE_PUMP_FLOW_CHECKS        1           // Do not error on HD pump flow checks
     #define DISABLE_PUMP_SPEED_CHECKS       1           // Do not error on HD pump speed checks
     #define DISABLE_PUMP_DIRECTION_CHECKS   1           // Do not error on HD pump direction checks
-//    #define DISABLE_SYRINGE_PUMP            1           // Disable syringe pump functionality
+    #define DISABLE_SYRINGE_PUMP            1           // Disable syringe pump functionality
     #define ALWAYS_ALLOW_SYRINGE_PUMP_CMDS  1           // Allow syringe pump commands at any time except when pump is busy
     #define DISABLE_PRESSURE_CHECKS         1           // Do not error on HD pressure checks
 //    #define DISABLE_UF_ALARMS               1           // Do not error on HD ultrafiltration checks
-    #define DISABLE_VALVE_ALARMS            1           // Do not error on HD valve position
+//    #define DISABLE_VALVE_ALARMS            1           // Do not error on HD valve position
     #define DISABLE_CAL_CHECK               1           // Disable calibration checks
 //    #define RUN_PUMPS_OPEN_LOOP             1           // BP and DPi pumps will be run open loop (no flow sensor feedback)
 //    #define RAW_FLOW_SENSOR_DATA            1           // Test build will not filter flow sensor data
@@ -66,7 +66,7 @@
     #define SKIP_PRIMING                    1           // Skip Pre-treatment Prime
     #define SKIP_WET_SELF_TESTS             1           // Skip Pre-treatment prime wet self-tests
 //    #define V1_5_SYSTEM                     1           // Build for v1.5 system
-//    #define V2_0_SYSTEM                     1           // Build for v2.0 system
+    #define V2_0_SYSTEM                     1           // Build for v2.0 system
 //    #define SKIP_SAMPLE_WATER               1           // Skip pre-treatment sample water
     #define SKIP_CONSUMABLE_TESTS           1           // Skip pre-treatment consumable Self-tests
     #define SKIP_DRY_SELF_TESTS             1           // Skip pre-treatment dry self-tests
@@ -77,8 +77,6 @@
 //    #define SKIP_CARTRIDGE_REMOVAL          1           // Skip cartridge removal check
     #define SKIP_EMPTY_RES_CHECK            1           // Skip reservoir empty check
     #define DISABLE_FPGA_COUNTER_CHECKS     1           // Disable alarms associated with FPGA read/error counters
-    #define DISABLE_VOLTAGE_MONITOR         1           // Disable voltage monitoring/alarms
-    #define ALLOW_1_MIN_TREATMENT_DURATION  1           // Allow user to change treatment duration to as low as 1 minute
 
 
     #include <stdio.h>