Index: firmware/App/Modes/Dialysis.c
===================================================================
diff -u -rdb291cc22fd8f10e6e47cad468e14ed5590a94f2 -r747c714d2b4f80b598a66326d62a179aeefda390
--- firmware/App/Modes/Dialysis.c	(.../Dialysis.c)	(revision db291cc22fd8f10e6e47cad468e14ed5590a94f2)
+++ firmware/App/Modes/Dialysis.c	(.../Dialysis.c)	(revision 747c714d2b4f80b598a66326d62a179aeefda390)
@@ -307,21 +307,21 @@
  *************************************************************************/
 void setDialysisBloodPumpFlowRate( U32 bPFlow )
 {
-   setBloodFlowRate = bPFlow;
+    setBloodFlowRate = bPFlow;
 
-   // Make rate changes in real time if currently performing dialysis.
-   if ( ( TREATMENT_DIALYSIS_STATE == getTreatmentState() ) && ( getDialysisState() != DIALYSIS_SALINE_BOLUS_STATE ) )
-   {
-       PUMP_CONTROL_MODE_T mode = PUMP_CONTROL_MODE_CLOSED_LOOP;
+    // Make rate changes in real time if currently performing dialysis.
+    if ( ( TREATMENT_DIALYSIS_STATE == getTreatmentState() ) && ( getDialysisState() != DIALYSIS_SALINE_BOLUS_STATE ) )
+    {
+        PUMP_CONTROL_MODE_T mode = PUMP_CONTROL_MODE_CLOSED_LOOP;
 
 #ifndef _RELEASE_
-       if ( SW_CONFIG_ENABLE_VALUE == getSoftwareConfigStatus( SW_CONFIG_ENABLE_BLOOD_PUMP_OPEN_LOOP ) )
-       {
-           mode = PUMP_CONTROL_MODE_OPEN_LOOP;
-       }
+        if ( SW_CONFIG_ENABLE_VALUE == getSoftwareConfigStatus( SW_CONFIG_ENABLE_BLOOD_PUMP_OPEN_LOOP ) )
+        {
+            mode = PUMP_CONTROL_MODE_OPEN_LOOP;
+        }
 #endif
-       setBloodPumpTargetFlowRate( setBloodFlowRate, MOTOR_DIR_FORWARD, mode );
-   }
+        setBloodPumpTargetFlowRate( setBloodFlowRate, MOTOR_DIR_FORWARD, mode );
+    }
 }
 
 /*********************************************************************//**
@@ -338,25 +338,25 @@
  *************************************************************************/
 void setDialysisDialInFlowAndUFRate( U32 dPFlow, F32 maxUFVol, F32 uFRate )
 {
-   setDialysateFlowRate = dPFlow;
-   setUFVolumeML = maxUFVol;
-   setUFRate = uFRate;
+    setDialysateFlowRate = dPFlow;
+    setUFVolumeML = maxUFVol;
+    setUFRate = uFRate;
 
-   // Make rate changes in real time if currently performing dialysis.
-   if ( ( TREATMENT_DIALYSIS_STATE == getTreatmentState() ) && ( getDialysisState() != DIALYSIS_SALINE_BOLUS_STATE ) )
-   {
-       PUMP_CONTROL_MODE_T mode = PUMP_CONTROL_MODE_CLOSED_LOOP;
+    // Make rate changes in real time if currently performing dialysis.
+    if ( ( TREATMENT_DIALYSIS_STATE == getTreatmentState() ) && ( getDialysisState() != DIALYSIS_SALINE_BOLUS_STATE ) )
+    {
+        PUMP_CONTROL_MODE_T mode = PUMP_CONTROL_MODE_CLOSED_LOOP;
 
 #ifndef _RELEASE_
-       if ( SW_CONFIG_ENABLE_VALUE == getSoftwareConfigStatus( SW_CONFIG_ENABLE_DIALYSATE_INLET_PUMP_OPEN_LOOP ) )
-       {
-           mode = PUMP_CONTROL_MODE_OPEN_LOOP;
-       }
+        if ( SW_CONFIG_ENABLE_VALUE == getSoftwareConfigStatus( SW_CONFIG_ENABLE_DIALYSATE_INLET_PUMP_OPEN_LOOP ) )
+        {
+            mode = PUMP_CONTROL_MODE_OPEN_LOOP;
+        }
 #endif
-       setDialInPumpTargetFlowRate( setDialysateFlowRate, MOTOR_DIR_FORWARD, mode );
+        setDialInPumpTargetFlowRate( setDialysateFlowRate, MOTOR_DIR_FORWARD, mode );
 
-       setDialOutPumpTargetRate( setDialysateFlowRate + (S32)setUFRate, MOTOR_DIR_FORWARD, PUMP_CONTROL_MODE_CLOSED_LOOP );
-   }
+        setDialOutPumpTargetRate( setDialysateFlowRate + (S32)setUFRate, MOTOR_DIR_FORWARD, PUMP_CONTROL_MODE_CLOSED_LOOP );
+    }
 }
 
 /*********************************************************************//**