Index: firmware/App/HDCommon.h
===================================================================
diff -u -r92c04526739f32e904fe258bd622aa08734ce343 -re518c218d137c8a2a0512bfcb7f28b3687fe8525
--- firmware/App/HDCommon.h	(.../HDCommon.h)	(revision 92c04526739f32e904fe258bd622aa08734ce343)
+++ firmware/App/HDCommon.h	(.../HDCommon.h)	(revision e518c218d137c8a2a0512bfcb7f28b3687fe8525)
@@ -25,21 +25,22 @@
 #define HD_VERSION_MAJOR        0
 #define HD_VERSION_MINOR        5
 #define HD_VERSION_MICRO        0
-#define HD_VERSION_BUILD        0
+#define HD_VERSION_BUILD        9010
 
 // ********** development build switches **********
 
 // TODO - remove build switches before release
 #ifndef _RELEASE_
 #ifndef _VECTORCAST_
-//    #define BOARD_WITH_NO_HARDWARE          1
+//    #define USING_DEBUGGER                  1           // Want to be able to use the debugger and have break points
+//    #define BOARD_WITH_NO_HARDWARE          1           // Target is a PCB w/ no hardware
 //    #define RUN_WITHOUT_DG                  1           // Run HD w/o DG
 //    #define SIMULATE_UI                     1           // Build w/o requirement that UI be there
 //    #define TASK_TIMING_OUTPUT_ENABLED      1           // Re-purposes alarm lamp pins for task timing
 //    #define DISABLE_ALARM_AUDIO             1           // Disable alarm audio
-    #define SKIP_POST                       1           // Skip POST tests - all pass
-    #define DONT_SKIP_NV_POST               1
-    #define DISABLE_AIR_TRAP_LEVELING       1           // Disable air trap level control
+//    #define SKIP_POST                       1           // Skip POST tests - all pass
+//    #define DONT_SKIP_NV_POST               1           // Do not skip NV Data POST
+//    #define DISABLE_AIR_TRAP_LEVELING       1           // Disable air trap level control
 //    #define DISABLE_3WAY_VALVES             1           // Disable 3-way valves
 //    #define TST_3WAY_VALVES_ALWAYS_OPEN     1           // After POST and homing, open all 4 valves
     #define DISABLE_ACCELS                  1           // Disable accelerometer POST and monitoring
@@ -50,14 +51,15 @@
     #define DISABLE_PUMP_SPEED_CHECKS       1           // Do not error on HD pump speed checks
     #define DISABLE_PUMP_DIRECTION_CHECKS   1           // Do not error on HD pump direction checks
     #define DISABLE_SYRINGE_PUMP            1           // Disable syringe pump functionality
+//    #define ALWAYS_ALLOW_SYRINGE_PUMP_CMDS  1           // Allow syringe pump commands at any time except when pump is busy
     #define DISABLE_PRESSURE_CHECKS         1           // Do not error on HD pressure checks
 //    #define DISABLE_UF_ALARMS               1           // Do not error on HD ultrafiltration checks
     #define DISABLE_VALVE_ALARMS            1           // Do not error on HD valve position
-    #define DISABLE_CAL_CHECK               1
+    #define DISABLE_CAL_CHECK               1           // Disable calibration checks
 //    #define RUN_PUMPS_OPEN_LOOP             1           // BP and DPi pumps will be run open loop (no flow sensor feedback)
 //    #define RAW_FLOW_SENSOR_DATA            1           // Test build will not filter flow sensor data
 //    #define READ_FPGA_ASYNC_DATA            1           // Test build reads non-priority register page every other time
-//    #define EMC_TEST_BUILD                  1           // EMC test build - HD/DG run separately but connected, HD pumps toggle on/off w/ stop button
+    #define EMC_TEST_BUILD                  1           // EMC test build - HD/DG run separately but connected, HD pumps toggle on/off w/ stop button
     #define ALARMS_DEBUG                    1           // Triggered alarms sent to debug UART
     #define SKIP_PRIMING                    1           // Skip Pre-treatment Prime
     #define SKIP_WET_SELF_TESTS             1           // Skip Pre-treatment prime wet self-tests
Index: firmware/App/Services/SystemCommMessages.c
===================================================================
diff -u -r0994065cce7875df917e6f96e7a0b78109980752 -re518c218d137c8a2a0512bfcb7f28b3687fe8525
--- firmware/App/Services/SystemCommMessages.c	(.../SystemCommMessages.c)	(revision 0994065cce7875df917e6f96e7a0b78109980752)
+++ firmware/App/Services/SystemCommMessages.c	(.../SystemCommMessages.c)	(revision e518c218d137c8a2a0512bfcb7f28b3687fe8525)
@@ -1236,6 +1236,7 @@
     payload.alarmsFlags |= ( almStatus.alarmsToEscalate             ? BIT_BY_POS(ALARM_STATE_FLAG_BIT_POS_ALARMS_TO_ESCALATE) : 0 );
     payload.alarmsFlags |= ( almStatus.alarmsSilenced               ? BIT_BY_POS(ALARM_STATE_FLAG_BIT_POS_ALARMS_SILENCED)    : 0 );
     payload.alarmsFlags |= ( almStatus.lampOn                       ? BIT_BY_POS(ALARM_STATE_FLAG_BIT_POS_LAMP_ON)            : 0 );
+    payload.alarmsFlags |= ( almStatus.noMinimize                   ? BIT_BY_POS(ALARM_STATE_FLAG_BIT_POS_NO_MINIMIZE)        : 0 );
     payload.alarmsFlags |= ( almStatus.topAlarmConditionnDetected   ? BIT_BY_POS(ALARM_STATE_FLAG_BIT_POS_TOP_CONDITION)      : 0 );
 
     memcpy( payloadPtr, &payload, sizeof( ALARM_COMP_STATUS_PAYLOAD_T ) );