Index: configurations/Alarms/Alarms.conf
===================================================================
diff -u -r3062967d4d109258d9ff6d26833e687eb6354d4f -rc913b39e469a884672f4a500c851af99a7035fba
--- configurations/Alarms/Alarms.conf	(.../Alarms.conf)	(revision 3062967d4d109258d9ff6d26833e687eb6354d4f)
+++ configurations/Alarms/Alarms.conf	(.../Alarms.conf)	(revision c913b39e469a884672f4a500c851af99a7035fba)
@@ -849,4 +849,15 @@
 Machine is in bypass and treatment will automatically resume once conductivity is within range.
 Review pH and conductivity based on facility policies once treatment is resumed. 
 
+[251]
+Title     = Dialysis Treatment Complete
+ListTitle = Dialysis Treatment Complete
+Press <b>‘OK’</b> to continue to end of treatment options 
 
+[252]
+Title     = End of Treatment Timeout
+ListTitle = End of Treatment Timeout
+The maximum time allowed on this screen has been reached. 
+Press <b>'Return Blood & End Treatment'</b> to begin the blood return process 
+
+
Index: configurations/Instructions/Instructions.conf
===================================================================
diff -u -rf9ec72965da0a260f4b63454e06633d7539b17ce -rc913b39e469a884672f4a500c851af99a7035fba
--- configurations/Instructions/Instructions.conf	(.../Instructions.conf)	(revision f9ec72965da0a260f4b63454e06633d7539b17ce)
+++ configurations/Instructions/Instructions.conf	(.../Instructions.conf)	(revision c913b39e469a884672f4a500c851af99a7035fba)
@@ -25,114 +25,123 @@
 # ######################################################################################################
 
 [Concentrates]
-Title = Connect Acid and Bicarbonate Concentrates
-Remove acid connector and connect to acid concentrate. = Concentrates_1.png
-Connect dry bicarbonate. = Concentrates_2.png
+Title = Connect Acid Concentrate and Dry Bicarbonate Cartridge
+Disconnect <$B53333>red</$> acid straw and connect to acid concentrate. = Concentrates_1.png
+Pull the <$#2268FF>blue </$> bicarbonate knob upwards and insert the dry bicarbonate cartridge. = Concentrates_2.png
 
 [Installation^Blood Tubing Set]
 Title = Install Blood Tubing Set
 Open the blood pump door. = Installation_BloodTube_1.png
-Insert blood tubing set and ensure it is secure. = Installation_BloodTube_2.png
-Push the blood tube into the blood pump. = Installation_BloodTube_3.png
-Close the blood pump door. = Installation_BloodTube_4.png
+Insert blood tubing bracket into the clip. Push inwards and ensure it is secure. = Installation_BloodTube_2.png
+Close the blood pump door. = Installation_BloodTube_3.png
+Press <b>'Auto-Load'</b> button. = Installation_BloodTube_4.png
 
 [Installation^Bloodlines]
-Title = Install Bloodlines
-Insert saline line into the first slot. = Installation_Bloodlines_1.png
-Insert <$B53333>arterial</$> line into the second slot. = Installation_Bloodlines_2.png
-Ensure the <$2268FF>venous</$> line is placed in the bubble detector. = Installation_Bloodlines_3.png
-Insert the <$2268FF>venous</$> line into the third slot. = Installation_Bloodlines_4.png
-Connect the <$B53333>arterial</$> and <$2268FF>venous</$> bloodlines using the recirculation connector. = Installation_Bloodlines_5.png
+Title = Insert Bloodlines
+Insert saline line into the leftmost slot. = Installation_Bloodlines_1.png
+Insert <$B53333>arterial</$> line into the middle slot. = Installation_Bloodlines_2.png
+Ensure <$2268FF>venous</$> line is placed in the air detector. = Installation_Bloodlines_3.png
+Insert <$2268FF>venous</$> line into the rightmost slot. = Installation_Bloodlines_4.png
+Ensure <$B53333>arterial</$> and <$2268FF>venous</$> bloodlines are tightened via the recirculation connector and placed behind the bar. = Installation_Bloodlines_5.png
 
 [Installation^Pressure Lines and Dialyzer]
-Title = Install Pressure Lines and Dialyzer
-Connect the <$B53333>arterial</$> pressure line to the <$B53333>arterial</$> pressure transducer port. = Installation_CPLD_1.png
-Connect the <$2268FF>venous</$> pressure line to the <$2268FF>venous</$> pressure transducer port. = Installation_CPLD_2.png
-Insert dialyzer into the holder and connect the dialysate lines. = Installation_CPLD_3.png
-Connect the bloodlines to the dialyzer. = Installation_CPLD_4.png
-Clamp the <$2268FF>venous</$> chamber line. = Installation_CPLD_5.png
-Clamp the heparin line. = Installation_CPLD_6.png
+Title = Connect Pressure Lines and Dialyzer
+Connect <$B53333>arterial</$> pressure line to <$B53333>arterial</$> pressure transducer port. = Installation_CPLD_1.png
+Connect <$2268FF>venous</$> pressure line to <$2268FF>venous</$> pressure transducer port. = Installation_CPLD_2.png
+Connect <$2268FF>venous</$> bloodline to the top of dialyzer and <$B53333>arterial</$> line to the bottom. = Installation_CPLD_4.png
+Connect <$2268FF>venous</$> dialysate line to the top of dialyzer and <$B53333>arterial</$> line to the bottom. = Installation_CPLD_4.png
+Insert dialyzer into dialyzer holder. = Installation_CPLD_3.png
+Clamp heparin line and <$2268FF>venous</$> infusion line. = Installation_CPLD_6.png
 
 [Installation^Saline]
 Title = Connect Saline Bag
+Uncap and insert saline line spike into saline bag. = Saline_3.png
+Clamp saline line and Y-connector. = Saline_2.png
 Hang saline bag on the hook. = Saline_1.png
-Clamp saline line. = Saline_2.png
-Use the saline line to spike saline bag. = Saline_3.png
 
 [Installation^Substitution]
 Title = Connect Substitution Line
+Connect substitution line to the machine. 
 Connect substitution line to the appropriate Pre or Post dilution port. = Saline_1.png
 
 [@Installation]
 Title = Install Concentrates and Blood Tubing Set
-Install acid and bicarbonate concentrates. = Install_Advanced_1.png
+Install acid concentrate and dry bicarbonate cartridge. = Install_Advanced_1.png
 Install blood tubing set, dialyzer, and saline bag. = Install_Advanced_2.png
 
+[@Installation^Substitution]
+Title = Install Concentrates and Blood Tubing Set
+Install acid concentrate and dry bicarbonate cartridge. = Install_Advanced_1.png
+Install blood tubing set, dialyzer, and connect substitution line. 
+
 [Connect]
-Title = Connect Bloodlines to the Patient
+Title = Connect Patient Bloodlines 
+Wash hands and apply personal protective equipment, per policy. 
 Clamp <$B53333>arterial</$> and <$2268FF>venous</$> bloodlines (2 clamps). = Connect_1.png
-Remove recirculation connector from the bloodlines. = Connect_2.png
-Connect bloodlines to patient access lines. = Connect_3.png
-Unclamp <$B53333>arterial</$> and <$2268FF>venous</$> bloodlines (2 clamps). = Connect_4.png
+Remove <$B53333>arterial</$> and <$2268FF>venous</$> bloodlines from recirculation connector and attach to patient access lines. = Connect_2.png
+Unclamp <$B53333>arterial</$> and <$2268FF>venous</$> bloodlines and patient access lines (4 clamps). = Connect_4.png
 
 [@Connect]
 Title = Connect Bloodlines to the Patient
-Connect bloodlines to patient access lines. = Connect_Advanced_1.png
+Connect <$B53333>arterial</$> and <$2268FF>venous</$> bloodlines to patient access lines. = Connect_Advanced_1.png
 
-[Disconnection]
-Title = Remove Concentrates and Blood Tubing Set
-Remove blood tubing set and dialyzer. = Install_Advanced_2.png
-Remove acid and bicarbonate concentrates. = Install_Advanced_1.png
 
 [Blood Return Setup]
 Title = Blood Return Connection
-Clamp <$B53333>arterial</$> bloodlines and disconnect. = Return_Blood_1.png
-Connect <$B53333>arterial</$> bloodline to the saline y-connector. = Return_Blood_2.png
-Unclamp <$B53333>arterial</$> bloodline and saline y-connector. = Return_Blood_3.png
+Clamp <$B53333>arterial</$> bloodline and <$B53333>arterial</$> access line (2 clamps). = Return_Blood_1.png
+Disconnect <$B53333>arterial</$> bloodline from <$B53333>arterial</$> access line. 
+Connect <$B53333>arterial</$> bloodline to the saline Y-connector. = Return_Blood_2.png
+Unclamp <$B53333>arterial</$> bloodline and saline Y-connector (2 clamps). = Return_Blood_3.png
+Press <b>'Start Blood Return'</b> button to begin blood return. 
 
 [$Blood Return Setup]
 Title = Blood Return Connection
-Clamp <$B53333>arterial</$> bloodlines and disconnect.
-Connect <$B53333>arterial</$> bloodline to the substitution line using a sterile connector.
-Unclamp <$B53333>arterial</$> bloodline and substitution line.
+Disconnect substitution line from dilution port and connect to a new, sterile recirculation connector. 
+Clamp <$B53333>arterial</$> bloodline and <$B53333>arterial</$> access line (2 clamps).
+Disconnect <$B53333>arterial</$> bloodline and connect to recirculation connector.
+Unclamp <$B53333>arterial</$> bloodline and substitution line (2 clamps).
+Press <b>'Start Blood Return'</b> button to begin blood return. 
 
 [Recirculate Set Up]
-Title = Connect Recirculation Lines
-Clamp <$2268FF>venous</$> bloodline and disconnect.
-Clamp <$B53333>arterial</$> bloodlines and disconnect from saline y-connector.
-Connect <$B53333>arterial</$> and <$2268FF>venous</$> bloodlines using the recirculation connector.
-Unclamp <$B53333>arterial</$> and <$2268FF>venous</$> bloodlines.
+Title = Connect Lines for Temporary Break
+Clamp <$2268FF>venous</$> bloodline, <$2268FF>venous</$> access line, and disconnect (2 clamps).
+Clamp <$B53333>arterial</$> bloodline, saline Y-connector, and disconnect (2 clamps).
+Connect <$B53333>arterial</$> and <$2268FF>venous</$> bloodlines using a new, sterile recirculation connector.
+Unclamp <$B53333>arterial</$> and <$2268FF>venous</$> bloodlines (2 clamps).
+Press <b>'Start Temporary Break'</b> button to begin the break. 
 
 [$Recirculate Set Up]
-Title = Connect Recirculation Lines
-Clamp <$2268FF>venous</$> bloodline and disconnect.
-Clamp <$B53333>arterial</$> and disconnect from the substitution line.
-Connect substitution line to the appropriate dilution port.
-Connect <$B53333>arterial</$> and <$2268FF>venous</$> bloodlines using the recirculation connector.
-Unclamp <$B53333>arterial</$> and <$2268FF>venous</$> bloodlines.
+Title = Connect Lines for Temporary Break
+Clamp <$2268FF>venous</$> bloodline, <$2268FF>venous</$> access line, and disconnect (2 clamps).
+Clamp <$B53333>arterial</$> bloodline and disconnect from substitution line.
+Cap the end of the substitution port.
+Connect <$B53333>arterial</$> and <$2268FF>venous</$> bloodlines using a new, recirculation connector.
+Unclamp <$B53333>arterial</$> and <$2268FF>venous</$> bloodlines (2 clamps).
+Press <b>'Start Temporary Break'</b> button to begin the break. 
 
 [Reconnect To Patient]
-Title = Connect Patient Bloodlines
-Clamp <$B53333>arterial</$> and <$2268FF>venous</$> bloodlines.
-Remove <$B53333>arterial</$> and <$2268FF>venous</$> line recirculation connector.
-Connect <$B53333>arterial</$> and <$2268FF>venous</$> bloodlines to patient access lines.
-Unclamp <$B53333>arterial</$> and <$2268FF>venous</$> bloodlines.
+Title = Reconnect Patient Bloodlines
+Clamp <$B53333>arterial</$> and <$2268FF>venous</$> bloodlines (2 clamps).
+Remove <$B53333>arterial</$> and <$2268FF>venous</$> bloodlines from recirculation connector and connect to patient access lines.
+Unclamp <$B53333>arterial</$> and <$2268FF>venous</$> bloodlines (4 clamps).
 
 [$Reconnect To Patient]
 Title = Connect Patient Bloodlines
-Clamp <$B53333>arterial</$> and <$2268FF>venous</$> bloodlines.
-Remove <$B53333>arterial</$> and <$2268FF>venous</$> line recirculation connector.
-Connect <$B53333>arterial</$> and <$2268FF>venous</$> bloodlines to patient access lines.
-Unclamp <$B53333>arterial</$> and <$2268FF>venous</$> bloodlines.
+Clamp <$B53333>arterial</$> and <$2268FF>venous</$> bloodlines (2 clamps).
+Remove <$B53333>arterial</$> and <$2268FF>venous</$> bloodlines from recirculation connector and connect to patient access lines.
+Unclamp <$B53333>arterial</$> and <$2268FF>venous</$> bloodlines (4 clamps).
+Connect substitution line to the appropriate Pre or Post dilution port. 
 
 [Disconnect^Disconnect Patient BloodLines]
 Title = Disconnect Patient BloodLines
-Clamp and disconnect patient bloodlines. = Install_Advanced_2.png
+Clamp and disconnect <$2268FF>venous</$> bloodline. = Install_Advanced_2.png
+Connect <$2268FF>venous</$> bloodline into <$2268FF>venous</$> needleless port.
+Connect <$B53333>arterial</$> bloodline into <$B53333>arterial</$> needleless port. 
 
 [Remove]
 Title = Remove Consumables and Disposables
-Reconnect the Hanson connectors from the dialyzer to the machine. = Install_Advanced_2.png
-Disconnect and remove acid concentrate and dry bicarbonate as needed. = Install_Advanced_1.png
-Tap <b>Auto Eject</b> button and remove the blood tube set. = Install_Advanced_2.png
+Remove acid concentrate and dry bicarbonate cartridge as needed.
+Remove dialysate quick connectors and connect to the machine. 
+Press <b>'Auto-Eject'</b> button to remove blood tubing set. 
+Discard blood tubing set per policy. 
 
-