Index: configurations/Alarms/Alarms.conf
===================================================================
diff -u -r05e5dc72479dd945df0e98df9a3e9f2ade153c7e -rf45e77d1da8294f866eeb7674c9ee8cbaed97bbc
--- configurations/Alarms/Alarms.conf	(.../Alarms.conf)	(revision 05e5dc72479dd945df0e98df9a3e9f2ade153c7e)
+++ configurations/Alarms/Alarms.conf	(.../Alarms.conf)	(revision f45e77d1da8294f866eeb7674c9ee8cbaed97bbc)
@@ -1 +1,660 @@
+[ALARM_ID_NO_ALARM]
+Title     = Indication for when no alarms is a possible situation
+ListTitle = 
+Message   = 
+
+[ALARM_ID_TD_SOFTWARE_FAULT]
+Title     = Service Required: Hemodialysis Device
+ListTitle = TD Software fault. Software found itself in an unexpected state
+Message   = TD Fault: SW Invalid State
+
+[ALARM_ID_DD_SOFTWARE_FAULT]
+Title     = Service Required: Dialysate Device
+ListTitle = DD software fault.  Software found itself in an unexpected state
+Message   = DD Fault: Software Invalid State
+
+[ALARM_ID_RO_SOFTWARE_FAULT]
+Title     = Service Required: Dialysate Device
+ListTitle = DD software fault.  Software found itself in an unexpected state
+Message   = DD Fault: Software Invalid State
+
+[ALARM_ID_TD_FPGA_POST_TEST_FAILED]
+Title     = Service Required: Hemodialysis Device
+ListTitle = TD FPGA POST failure
+Message   = TD POST: FPGA Compatibility
+
+[ALARM_ID_TD_WATCHDOG_POST_TEST_FAILED]
+Title     = Service Required: Hemodialysis Device
+ListTitle = TD Watchdog POST failure
+Message   = TD POST: WD Safestate
+
+[ALARM_ID_TD_UI_COMM_POST_FAILED]
+Title     = Service Required: Hemodialysis Device
+ListTitle = UI communication POST failure.  UI failed to communicate within a reasonable time after power up
+Message   = TD POST: Proc- UI Comm
+
+[ALARM_ID_TD_FPGA_CLOCK_SPEED_CHECK_FAILURE]
+Title     = Service Required: Hemodialysis Device
+ListTitle = TD processor clock speed checks against FPGA clock failure
+Message   = TD Fault: Proc- FPGA Clock
+
+[ALARM_ID_TD_FPGA_COMM_TIMEOUT]
+Title     = Service Required: Hemodialysis Device
+ListTitle = TD FPGA communication down for too long
+Message   = TD Fault: FPGA Com
+
+[ALARM_ID_TD_UI_COMM_TIMEOUT]
+Title     = Service Required: Hemodialysis Device
+ListTitle = User interface communication timeout
+Message   = TD Fault: UI Comm
+
+[ALARM_ID_TD_DD_COMM_TIMEOUT]
+Title     = Communication Error
+ListTitle = Dialysate generator communication timeout
+Message   = Loss of DD Comm (Timeout)
+
+[ALARM_ID_TD_COMM_TOO_MANY_BAD_CRCS]
+Title     = Service Required: Hemodialysis Device
+ListTitle = Too many bad CRCs detected on received system messages
+Message   = TD Fault: CAN CRC Com
+
+[ALARM_ID_TD_CAN_MESSAGE_NOT_ACKED_BY_UI]
+Title     = Service Required: Hemodialysis Device
+ListTitle = System message that required acknowledgment was not acknowledged
+Message   = TD Fault: CAN ACK UI Com
+
+[ALARM_ID_TD_CAN_MESSAGE_NOT_ACKED_BY_DD]
+Title     = Communication Error
+ListTitle = TD to DD comm error.
+Message   = Loss of DD Comm (DD ACK)
+
+[ALARM_ID_TD_CRITICAL_DATA_ERROR]
+Title     = Service Required: Hemodialysis Device
+ListTitle = TD critical data integrity check failed
+Message   = TD Fault: Critical Data Err
+
+[ALARM_ID_DD_CRITICAL_DATA_ERROR]
+Title     = Service Required: Dialysate Device
+ListTitle = DD critical data integrity check failed
+Message   = DD Fault: Critical Data Err
+
+[ALARM_ID_TD_WATCHDOG_EXPIRED]
+Title     = Service Required: Hemodialysis Device
+ListTitle = TD watchdog expired
+Message   = TD Fault: WD Error
+
+[ALARM_ID_DD_WATCHDOG_EXPIRED]
+Title     = Service Required: Dialysate Device
+ListTitle = DD watchdog expired
+Message   = DD Fault: WD Error
+
+[ALARM_ID_DD_COMM_TOO_MANY_BAD_CRCS]
+Title     = Service Required: Dialysate Device
+ListTitle = Too many bad CRCs detected on received system messages
+Message   = DD Fault: CAN CRC Com
+
+[ALARM_ID_DD_CAN_MESSAGE_NOT_ACKED_BY_RO]
+Title     = Service Required: Dialysate Device
+ListTitle = DD to RO comm error
+Message   = Loss of RO Comm (RO ACK)
+
+[ALARM_ID_DD_CAN_MESSAGE_NOT_ACKED_BY_TD]
+Title     = Service Required: Dialysate Device
+ListTitle = DD to TD comm error
+Message   = Loss of TD Comm (TD ACK)
+
+[ALARM_ID_DD_FPGA_POST_TEST_FAILED]
+Title     = Service Required: Dialysate Device
+ListTitle = DD FPGA POST failure
+Message   = DD POST: FPGA Compatibility
+
+[ALARM_ID_DD_FPGA_CLOCK_SPEED_CHECK_FAILURE]
+Title     = Service Required: Dialysate Device
+ListTitle = FPGA clock speed failure
+Message   = DD Fault: Proc- FPGA Clock
+
+[ALARM_ID_DD_FPGA_COMM_TIMEOUT]
+Title     = Service Required: Dialysate Device
+ListTitle = DD FPGA communication down for too long
+Message   = DD Fault: FPGA Com
+
+[ALARM_ID_TD_ALARM_AUDIO_SELF_TEST_FAILURE]
+Title     = Service Required: Hemodialysis Device
+ListTitle = TD alarm audio failed POST
+Message   = TD POST: Primary Alarm Current
+
+[ALARM_ID_DD_VALVE_CONTROL_FAILURE]
+Title     = Service Required: Dialysate Device
+ListTitle = DD FPGA not accepting commanded valve states
+Message   = DD Fault: Valve Control
+
+[ALARM_ID_TD_ARTERIAL_SENSOR_TIMEOUT_FAULT]
+Title     = Service Required: Hemodialysis Device
+ListTitle = TD arterial pressure sensor reporting error or not being read successfully
+Message   = TD Arterial Pressure Sensor Error
+
+[ALARM_ID_TD_VENOUS_SENSOR_TIMEOUT_FAULT]
+Title     = Service Required: Hemodialysis Device
+ListTitle = TD venous pressure sensor reporting error or not being read successfully
+Message   = TD Venous Pressure Sensor Error
+
+[ALARM_ID_DD_HYD_OUTLET_PRES_TIMEOUT_FAULT]
+Title     = Service Required: Dialysate Device
+ListTitle = DD hydraulics outlet pressure sensor reporting error or not being read successfully
+Message   = DD Hyd outlet Pressure Sensor Error
+
+[ALARM_ID_DD_BIBAG_PRES_TIMEOUT_FAULT]
+Title     = Service Required: Dialysate Device
+ListTitle = DD bibag pressure sensor reporting error or not being read successfully
+Message   = DD Bibag Pressure Sensor Error
+
+[ALARM_ID_DD_SPENT_DIALYSATE_PRES_TIMEOUT_FAULT]
+Title     = Service Required: Dialysate Device
+ListTitle = DD spent dialysate pressure sensor reporting error or not being read successfully
+Message   = DD Spent Dial Pressure Sensor Error
+
+[ALARM_ID_DD_FRESH_DIALYSATE_PRES_TIMEOUT_FAULT]
+Title     = Service Required: Dialysate Device
+ListTitle = DD fresh dialysate pressure sensor reporting error or not being read successfully
+Message   = DD Fresh Dial Pressure Sensor Error
+
+[ALARM_ID_DD_TRANSMEMB_PRES_TIMEOUT_FAULT]
+Title     = Service Required: Dialysate Device
+ListTitle = DD transmembrane sensor reporting error or not being read successfully
+Message   = DD Transmemb Pressure Sensor Error
+
+[ALARM_ID_TD_VOLTAGE_OUT_OF_RANGE]
+Title     = Service Required: Hemodialysis Device
+ListTitle = TD monitored voltage is out of range
+Message   = TD Fault: Voltage Monitor
+
+[ALARM_ID_TD_AC_POWER_LOST]
+Title     = Power Loss
+ListTitle = TD AC power lost alarm
+Message   = Loss of AC Power
+
+[ALARM_ID_TD_AC_POWER_LOST_IN_TREATMENT]
+Title     = Power Loss
+ListTitle = TD AC power lost alarm
+Message   = Blood Stop: Loss of AC Power
+
+[ALARM_ID_DD_D17_COND_SENSOR_FPGA_FAULT]
+Title     = Service Required: Dialysate Device
+ListTitle = DD conductivity sensor (D17) located before balancing chamber  reporting error or not being read successfully
+Message   = DD Conductivity Sensor Error
+
+[ALARM_ID_DD_D27_COND_SENSOR_FPGA_FAULT]
+Title     = Service Required: Dialysate Device
+ListTitle = DD conductivity sensor (D27) located after balancing chamber reporting error or not being read successfully
+Message   = DD Conductivity Sensor Error
+
+[ALARM_ID_DD_D29_COND_SENSOR_FPGA_FAULT]
+Title     = Service Required: Dialysate Device
+ListTitle = DD conductivity sensor (D29) located after balancing chamber reporting error or not being read successfully
+Message   = DD Conductivity Sensor Error
+
+[ALARM_ID_DD_D43_COND_SENSOR_FPGA_FAULT]
+Title     = Service Required: Dialysate Device
+ListTitle = DD conductivity sensor (D43) located in spent dialysate path reporting error or not being read successfully
+Message   = DD Conductivity Sensor Error
+
+[ALARM_ID_TD_VENOUS_BUBBLE_DETECTED]
+Title     = Venous Air Detected
+ListTitle = TD venous air bubble detected alarm
+Message   = Blood Stop: Venous Air Bubble
+
+[ALARM_ID_TD_CARTRIDGE_DOOR_OPENED]
+Title     = Blood Pump Stopped: Door Open
+ListTitle = TD cartridge door opened alarm
+Message   = Blood Stop: Door Open
+
+[ALARM_ID_TD_STUCK_BUTTON_TEST_FAILED]
+Title     = Stuck Button
+ListTitle = TD Stuck button POST failure.  Stop or Off button detected to be pressed for at least 1 second during test shortly after power up
+Message   = TD POST: Stuck Button
+
+[ALARM_ID_TD_ARTERIAL_PRESSURE_LOW]
+Title     = Low Arterial Pressure
+ListTitle = Arterial pressure too low during treatment
+Message   = Blood Stop: Arterial Pres. Low
+
+[ALARM_ID_TD_ARTERIAL_PRESSURE_HIGH]
+Title     = High Arterial Pressure
+ListTitle = Arterial pressure too high during treatment
+Message   = Blood Stop: Arterial Pres. High
+
+[ALARM_ID_TD_ARTERIAL_PRESSURE_OUT_OF_RANGE]
+Title     = Service Required: Hemodialysis Device
+ListTitle = TD arterial pressure sensor is reading out of range
+Message   = TD Fault: Arterial Press Range
+
+[ALARM_ID_TD_ARTERIAL_PRESSURE_SELF_TEST_FAILURE]
+Title     = Self Test: Cartridge
+ListTitle = TD arterial pressure self-test failure alarm
+Message   = Process: Pre- Tx Remove Cartridge
+
+[ALARM_ID_TD_VENOUS_PRESSURE_LOW]
+Title     = Low Venous Pressure
+ListTitle = Venous pressure too low during treatment
+Message   = Blood Stop: Venous Pres. Low
+
+[ALARM_ID_TD_VENOUS_PRESSURE_HIGH]
+Title     = High Venous Pressure
+ListTitle = Venous pressure too high during treatment
+Message   = Blood Stop: Venous Pres. High
+
+[ALARM_ID_TD_VENOUS_PRESSURE_OUT_OF_RANGE]
+Title     = Service Required: Hemodialysis Device
+ListTitle = TD venous pressure sensor is reading out of range
+Message   = TD Fault: Venous Press Range
+
+[ALARM_ID_TD_VENOUS_PRESSURE_SELF_TEST_FAILURE]
+Title     = Self Test: Cartridge
+ListTitle = TD venous pressure self-test failure alarm
+Message   = Process: Pre- Tx Remove Cartridge
+
+[ALARM_ID_TD_PRE_TREATMENT_DRY_PRESSURE_TEST_FAILURE]
+Title     = Self Test: Cartridge Check
+ListTitle = TD pre-treatment mode dry self-tests failure
+Message   = Process: Pre- Tx Dry Self- Test
+
+[ALARM_ID_DD_D11_PUMP_SPEED_CONTROL_ERROR]
+Title     = Service Required: Dialysate Device
+ListTitle = DD concentrate pump D11_PUMP speed control error
+Message   = DD Fault: Pump Speed Fault
+
+[ALARM_ID_DD_D10_PUMP_SPEED_CONTROL_ERROR]
+Title     = Service Required: Dialysate Device
+ListTitle = DD concentrate pump D10_PUMP speed control error
+Message   = DD Fault: Pump Speed Fault
+
+[ALARM_ID_DD_CONC_PUMP_HALL_SENSOR_OUT_OF_RANGE]
+Title     = Service Required: Dialysate Device
+ListTitle = DD concentrate pump hall sensor out of range.
+Message   = DD Fault: Pump Speed Fault
+
+[ALARM_ID_DD_CONCENTRATE_PUMP_FAULT]
+Title     = Service Required: Dialysate Device
+ListTitle = DD concentrate pump fault
+Message   = DD Fault: Pump Fault
+
+[ALARM_ID_DD_TEMPERATURE_SENSOR_OUT_OF_RANGE]
+Title     = Service Required: Dialysate Device
+ListTitle = DD temperature sensor out of range
+Message   = DD Fault: Temp Sensor Range
+
+[ALARM_ID_DD_RTD_SENSORS_FPGA_FAULT]
+Title     = Service Required: Dialysate Device
+ListTitle = DD temperature sensors not being read successfully
+Message   = DD Fault: Temperature RTD Comm
+
+[ALARM_ID_DD_BARO_SENSOR_FPGA_FAULT]
+Title     = Service Required: Dialysate Device
+ListTitle = DD barometric sensor not being read successfully
+Message   = DD Fault: Baro temp Comm
+
+[ALARM_ID_DD_BAROMETRIC_SENSOR_COEFFS_BAD_CRC]
+Title     = Service Required: Dialysate Device
+ListTitle = DD barometric pressure sensor bad coefficients CRC
+Message   = DD Fault: Baro temp Cal CRC
+
+[ALARM_ID_DD_D12_PUMP_RPM_OUT_OF_RANGE]
+Title     = Service Required: Dialysate Device
+ListTitle = DD fresh dialysate pump RPM out of range
+Message   = DD Fault: Fresh Dial Pump Speed Fault
+
+[ALARM_ID_DD_D12_PUMP_OFF_FAULT]
+Title     = Service Required: Dialysate Device
+ListTitle = DD fresh dialysate pump off fault
+Message   = DD Fault: Fresh Dial Pump Speed Not Off
+
+[ALARM_ID_DD_D12_PUMP_CURRENT_OUT_OF_RANGE]
+Title     = Service Required: Dialysate Device
+ListTitle = DD fresh dialysate pump current out of range
+Message   = DD Fault: Fresh Dial Pump Current
+
+[ALARM_ID_DD_D12_PUMP_DIRECTION_INVALID]
+Title     = Service Required: Dialysate Device
+ListTitle = DD fresh dialysate pump invalid direction
+Message   = DD Fault: Fresh Dial Pump Dir Fault
+
+[ALARM_ID_DD_D12_PUMP_DIRECTION_FPGA_FAULT]
+Title     = Service Required: Dialysate Device
+ListTitle = DD fresh dialysate pump direction FPGA fault
+Message   = DD Fault: Fresh Dial pump Dir Err Cnt
+
+[ALARM_ID_DD_D48_PUMP_RPM_OUT_OF_RANGE]
+Title     = Service Required: Dialysate Device
+ListTitle = DD spent dialysate pump RPM out of range
+Message   = DD Fault: Spent Dial Pump Speed Fault
+
+[ALARM_ID_DD_D48_PUMP_OFF_FAULT]
+Title     = Service Required: Dialysate Device
+ListTitle = DD spent dialysate pump off fault
+Message   = DD Fault: Spent Dial Pump Speed Not Off
+
+[ALARM_ID_DD_D48_PUMP_CURRENT_OUT_OF_RANGE]
+Title     = Service Required: Dialysate Device
+ListTitle = DD spent dialysate pump current out of range
+Message   = DD Fault: Spent Dial Pump Current
+
+[ALARM_ID_DD_D48_PUMP_DIRECTION_INVALID]
+Title     = Service Required: Dialysate Device
+ListTitle = DD spent dialysate pump invalid direction
+Message   = DD Fault: Spent Dial Pump Dir Fault
+
+[ALARM_ID_DD_D48_PUMP_DIRECTION_FPGA_FAULT]
+Title     = Service Required: Dialysate Device
+ListTitle = DD spent dialysate pump direction FPGA fault
+Message   = DD Fault: Spent Dial pump Dir Err Cnt
+
+[ALARM_ID_DD_FLUID_TOO_LOW_WHILE_D5_HEAT_IS_ON]
+Title     = Service Required: Dialysate Device
+ListTitle = DD D5 heater is On with low fluid level
+Message   = DD Fault: Heater On With No Fluid
+
+[ALARM_ID_DD_FLUID_TOO_LOW_WHILE_D45_HEAT_IS_ON]
+Title     = Service Required: Dialysate Device
+ListTitle = DD D45 heater is On with low fluid level
+Message   = DD Fault: Heater On With No Fluid
+
+[ALARM_ID_DD_WATER_INLET_INPUT_PRES_TIMEOUT_FAULT]
+Title     = Service Required: Dialysate Device
+ListTitle = DD water inlet input pressure sensor reporting error or not being read successfully
+Message   = DD Water Inlet Input Press Sensor Error
+
+[ALARM_ID_DD_WATER_INLET_OUTPUT_PRES_TIMEOUT_FAULT]
+Title     = Service Required: Dialysate Device
+ListTitle = DD water inlet output pressure sensor reporting error or not being read successfully
+Message   = DD Water Inlet Output Press Sensor Error
+
+[ALARM_ID_DD_INLET_WATER_PRESSURE_IN_LOW_RANGE]
+Title     = Incoming Water Pressure Input Low
+ListTitle = DD Inlet water pressure input too low
+Message   = DD: Inlet Water Pres Input Low
+
+[ALARM_ID_DD_INLET_WATER_PRESSURE_IN_HIGH_RANGE]
+Title     = Incoming Water Pressure Input High
+ListTitle = DD inlet water pressure input is too high
+Message   = DD: Inlet Water Pres Input High
+
+[ALARM_ID_DD_INLET_WATER_PRESSURE_OUT_LOW_RANGE]
+Title     = Incoming Water Pressure Output Low
+ListTitle = DD Inlet water pressure output too low
+Message   = DD: Inlet Water Pres Output Low
+
+[ALARM_ID_DD_INLET_WATER_PRESSURE_OUT_HIGH_RANGE]
+Title     = Incoming Water Pressure Output High
+ListTitle = DD inlet water pressure output is too high
+Message   = DD: Inlet Water Pres Output High
+
+[ALARM_ID_TD_AIR_TRAP_FILL_DURING_TREATMENT]
+Title     = Blood Pump Stopped: Venous Air Detector
+ListTitle = Air trap fill timeout during treatment
+Message   = Blood Stop: Air Trap Fill
+
+[ALARM_ID_TD_AIR_TRAP_ILLEGAL_LEVELS]
+Title     = Service Required: Hemodialysis Device
+ListTitle = Air trap level sensors reporting illegal combination of air/fluid
+Message   = TD Fault: Air Trap Sensor
+
+[ALARM_ID_TD_PINCH_VALVE_FAULT]
+Title     = Service Required: Hemodialysis Device
+ListTitle = Pinch valve reporting a fault
+Message   = TD Fault: Pinch Valve
+
+[ALARM_ID_TD_VALVE_HOMING_FAILED]
+Title     = Service Required: Hemodialysis Device
+ListTitle = TD valve homing failed
+Message   = TD Fault: Valve Home
+
+[ALARM_ID_TD_VALVE_TRANSITION_TIMEOUT]
+Title     = Service Required: Hemodialysis Device
+ListTitle = TD valve transition time out
+Message   = TD Fault: Valve Transition Err
+
+[ALARM_ID_RO_CAN_MESSAGE_NOT_ACKED_BY_DD]
+Title     = Communication Error
+ListTitle = DD to RO comm error.
+Message   = RO Loss of DD Comm (DD ACK)
+
+[ALARM_ID_RO_FPGA_COMM_TIMEOUT]
+Title     = Service Required: Dialysate Device
+ListTitle = RO FPGA communication down for too long
+Message   = RO Fault: FPGA Comm
+
+[ALARM_ID_RO_COMM_TOO_MANY_BAD_CRCS]
+Title     = Service Required: Hemodialysis Device
+ListTitle = RO Too many bad CRCs detected on received system messages
+Message   = RO Fault: CAN CRC Comm
+
+[ALARM_ID_RO_VALVE_CONTROL_FAILURE]
+Title     = Service Required: Filtration Device
+ListTitle = RO FPGA not accepting commanded valve states
+Message   = RO Fault: Valve Control
+
+[ALARM_ID_DD_BC_STATE1_FILL_START_PRESSURE_OUT_OF_RANGE]
+Title     = Service Required: Dialysate Device
+ListTitle = DD balancing chamber state 1 fill start pressure is not in range
+Message   = DD Fault: BC Pressure not in range
+
+[ALARM_ID_DD_BC_STATE1_FILL_END_PRESSURE_OUT_OF_RANGE]
+Title     = Service Required: Dialysate Device
+ListTitle = DD balancing chamber state 1 fill end pressure is not in range
+Message   = DD Fault: BC Pressure not in range
+
+[ALARM_ID_DD_BC_STATE2_FILL_START_PRESSURE_OUT_OF_RANGE]
+Title     = Service Required: Dialysate Device
+ListTitle = DD balancing chamber state 2 fill start pressure is not in range
+Message   = DD Fault: BC Pressure not in range
+
+[ALARM_ID_DD_BC_STATE2_FILL_END_PRESSURE_OUT_OF_RANGE]
+Title     = Service Required: Dialysate Device
+ListTitle = DD balancing chamber state 2 fill end pressure is not in range
+Message   = DD Fault: BC Pressure not in range
+
+[ALARM_ID_DD_GEND_HYD_CHAMBER_PRESS_OUT_OF_RANGE]
+Title     = Service Required: Dialysate Device
+ListTitle = DD hydraulics chamber degassing pressure is not in range
+Message   = DD Fault: Hyd Cham Neg Pres not in range
+
+[ALARM_ID_AVAILABLE_92]
+Title     = 
+ListTitle = 
+Message   = 
+
+[ALARM_ID_AVAILABLE_93]
+Title     = 
+ListTitle = 
+Message   = 
+
+[ALARM_ID_DD_BC_STATE1_FILL_PRESSURE_DROP_OUT_OF_RANGE]
+Title     = Service Required: Dialysate Device
+ListTitle = DD balancing chamber state 1 fill initiated and pressure drop is not in range
+Message   = DD Fault: BC Pressure not in range
+
+[ALARM_ID_DD_BC_STATE2_FILL_PRESSURE_DROP_OUT_OF_RANGE]
+Title     = Service Required: Dialysate Device
+ListTitle = DD balancing chamber state 2 fill initiated and pressure drop is not in range
+Message   = DD Fault: BC Pressure not in range
+
+[ALARM_ID_TD_TREATMENT_STOPPED_BY_USER]
+Title     = Blood Pump Stopped: Treatment Paused
+ListTitle = TD treatment stopped by user action - pressed stop button
+Message   = Blood Stopped: Treatment Pause
+
+[ALARM_ID_DD_D74_COND_SENSOR_FPGA_FAULT]
+Title     = Service Required: Dialysate Device
+ListTitle = DD conductivity sensor (D74) located before balancing chamber reporting error or not being read successfully
+Message   = DD Conductivity Sensor Error
+
+[ALARM_ID_AVAILABLE_98]
+Title     = 
+ListTitle = 
+Message   = 
+
+[ALARM_ID_AVAILABLE_99]
+Title     = 
+ListTitle = 
+Message   = 
+
+[ALARM_ID_TD_COMM_TIMEOUT]
+Title     = Service Required: Hemodialysis Device
+ListTitle = TD communication timeout
+Message   = TD Fault: UI- Proc Comm
+
+[ALARM_ID_UI_POST_FAILURE_OS_VERSION]
+Title     = Service Required: Hemodialysis Device
+ListTitle = UI POST OS Version compatibility failure
+Message   = TD POST: OS Version
+
+[ALARM_ID_UI_POST_FAILURE_SHASUM]
+Title     = Service Required: Hemodialysis Device
+ListTitle = UI POST Application Integrity (Sha256Sum) failure
+Message   = TD POST: UI Image
+
+[ALARM_ID_UI_POST_FAILURE_CANBUS]
+Title     = Service Required: Hemodialysis Device
+ListTitle = UI POST CANBus failure
+Message   = TD POST: UI CAN Driver
+
+[ALARM_ID_UI_POST_FAILURE_DISPLAY]
+Title     = Service Required: Hemodialysis Device
+ListTitle = If the UI POST reports display failure.
+Message   = UI POST Display failure
+
+[ALARM_ID_UI_POST_FAILURE_TOUCH]
+Title     = Service Required: Hemodialysis Device
+ListTitle = UI POST Touch failure
+Message   = TD POST: UI Touch Driver
+
+[ALARM_ID_UI_POST_FAILURE_SDCARD]
+Title     = Service Required: Hemodialysis Device
+ListTitle = UI POST SD-Card failure
+Message   = TD POST: UI SD- Card
+
+[ALARM_ID_UI_POST_FAILURE_RTC]
+Title     = Service Required: Hemodialysis Device
+ListTitle = UI POST RTC failure
+Message   = TD POST: UI RTC
+
+[ALARM_ID_UI_POST_FAILURE_WIFI]
+Title     = Service Required: Hemodialysis Device
+ListTitle = UI POST WiFi failure
+Message   = TD POST: UI WiFi
+
+[ALARM_ID_UI_POST_FAILURE_BLUETOOTH]
+Title     = Service Required: Hemodialysis Device
+ListTitle = UI POST Bluetooth failure
+Message   = TD POST: UI Bluetooth
+
+[ALARM_ID_UI_POST_FAILURE_ETHERNET]
+Title     = Service Required: Hemodialysis Device
+ListTitle = UI POST Ethernet failure
+Message   = TD POST: UI Ethernet
+
+[ALARM_ID_UI_POST_FAILURE_SOUND]
+Title     = Service Required: Hemodialysis Device
+ListTitle = UI POST Sound failure
+Message   = TD POST: UI Sound
+
+[ALARM_ID_UI_POST_FAILURE_CLOUDSYNC]
+Title     = Service Required: Hemodialysis Device
+ListTitle = UI POST cloud sync POST failure
+Message   = TD POST: UI CloudSync
+
+[ALARM_ID_UI_POST_FAILURE_INVALID_YEAR]
+Title     = Service Required: Hemodialysis Device
+ListTitle = UI POST Invalid Year
+Message   = TD POST Alarm: UI Invalid Year
+
+[ALARM_ID_UI_POST_FAILURE_SETTINGS_BAD]
+Title     = Service Required: Hemodialysis Device
+ListTitle = UI POST Bad Settings
+Message   = TD POST Alarm: UI Bad Settings
+
+[ALARM_ID_UI_EVNT_FAILURE_SDCARD]
+Title     = Service Required: Hemodialysis Device
+ListTitle = SD card is non-operational
+Message   = TD Fault: UI- SD- Card Fault
+
+[ALARM_ID_UI_RESERVED_116]
+Title     = Service Required: Hemodialysis Device
+ListTitle = RESERVED
+Message   = TD Fault: UI- RESERVED
+
+[ALARM_ID_UI_RESERVED_117]
+Title     = Service Required: Hemodialysis Device
+ListTitle = RESERVED
+Message   = TD Fault: UI- RESERVED
+
+[ALARM_ID_UI_RESERVED_118]
+Title     = Service Required: Hemodialysis Device
+ListTitle = RESERVED
+Message   = TD Fault: UI- RESERVED
+
+[ALARM_ID_UI_RESERVED_119]
+Title     = Service Required: Hemodialysis Device
+ListTitle = RESERVED
+Message   = TD Fault: UI- RESERVED
+
+[ALARM_ID_UI_RESERVED_120]
+Title     = Service Required: Hemodialysis Device
+ListTitle = RESERVED
+Message   = TD Fault: UI- RESERVED
+
+[ALARM_ID_UI_RESERVED_121]
+Title     = Service Required: Hemodialysis Device
+ListTitle = RESERVED
+Message   = TD Fault: UI- RESERVED
+
+[ALARM_ID_UI_RESERVED_122]
+Title     = Service Required: Hemodialysis Device
+ListTitle = RESERVED
+Message   = TD Fault: UI- RESERVED
+
+[ALARM_ID_UI_RESERVED_123]
+Title     = Service Required: Hemodialysis Device
+ListTitle = RESERVED
+Message   = TD Fault: UI- RESERVED
+
+[ALARM_ID_UI_RESERVED_124]
+Title     = Service Required: Hemodialysis Device
+ListTitle = RESERVED
+Message   = TD Fault: UI- RESERVED
+
+[ALARM_ID_UI_RESERVED_125]
+Title     = Service Required: Hemodialysis Device
+ListTitle = RESERVED
+Message   = TD Fault: UI- RESERVED
+
+[ALARM_ID_UI_RESERVED_126]
+Title     = Service Required: Hemodialysis Device
+ListTitle = RESERVED
+Message   = TD Fault: UI- RESERVED
+
+[ALARM_ID_UI_RESERVED_127]
+Title     = Service Required: Hemodialysis Device
+ListTitle = RESERVED
+Message   = TD Fault: UI- RESERVED
+
+[ALARM_ID_UI_RESERVED_128]
+Title     = Service Required: Hemodialysis Device
+ListTitle = RESERVED
+Message   = TD Fault: UI- RESERVED
+
+[ALARM_ID_UI_RESERVED_129]
+Title     = Service Required: Hemodialysis Device
+ListTitle = RESERVED
+Message   = TD Fault: UI- RESERVED
+
+[ALARM_ID_UI_RESERVED_130]
+Title     = Service Required: Hemodialysis Device
+ListTitle = RESERVED
+Message   = TD Fault: UI- RESERVED
+
+[ALARM_ID_BATTERY_LOW]
+Title     = Battery Capacity Low
+ListTitle = Insufficient battery charge to support 20 min without A/C power
+Message   = TD Alarm (Low): Battery Low
+