Index: build/AlarmMapping.py
===================================================================
diff -u -r0e748d1af8c6854f89b9183270a533f9398088fb -rdafe0a1608f7b26bb40d8110b45af38a60ab6321
--- build/AlarmMapping.py	(.../AlarmMapping.py)	(revision 0e748d1af8c6854f89b9183270a533f9398088fb)
+++ build/AlarmMapping.py	(.../AlarmMapping.py)	(revision dafe0a1608f7b26bb40d8110b45af38a60ab6321)
@@ -27,7 +27,7 @@
   25 : "DG accelerometer invalid calibration record."                                                                                                
   26 : "HD accelerometer invalid calibration record."                                                                                                
   27 : "HD blood leak sensor zero and self test sequence failed."                                                                                    
-  28 : "Not used."                                                                                                                                   
+  28 : "DG two wire sensors FPGA fault."                                                                                                             
   29 : "HD heparin force sensor invalid calibration record."                                                                                         
   30 : "HD Software fault.\nSoftware found itself in an unexpected state."                                                                           
   31 : "Blood pump failed motor controller current check.\nToo high when pump should be off or out of range when pump should be running."            
@@ -219,7 +219,7 @@
  217 : "HD blood prime volume check failure."                                                                                                        
  218 : "HD syringe detected alarm."                                                                                                                  
  219 : "HD syringe pump syringe removed alarm."                                                                                                      
- 220 : "HD battery pack SOC is too low."                                                                                                             
+ 220 : "DG THd sensors FPGA fault."                                                                                                                  
  221 : "HD Saline bag is empty."                                                                                                                     
  222 : "HD dialysate temperature too high alarm."                                                                                                    
  223 : "HD dialysate temperature too low alarm."                                                                                                     
@@ -295,7 +295,14 @@
  293 : "HD processor is in Disinfect Chemical mode."                                                                                                 
  294 : "HD processor Disinfect Chemical mode instructions to user."                                                                                  
  295 : "UI POST CloudSync failure."                                                                                                                  
- 296 : "Total number of alarms."                                                                                                                     
+ 296 : "DG TDi sensors FPGA fault."                                                                                                                  
+ 297 : "DG TRo sensors FPGA fault."                                                                                                                  
+ 298 : "DG baro sensor FPGA fault."                                                                                                                  
+ 299 : "DG disinfect has been expired."                                                                                                              
+ 300 : "DG service time interval has elapsed."                                                                                                       
+ 301 : "DG primary heater power voltage out of range."                                                                                               
+ 302 : "DG processor RAM error."                                                                                                                     
+ 303 : "Total number of alarms."                                                                                                                     
 }                         
                           
 # dictionary of rejection reason from application source code. 
Index: build/Alarms.xlsx
===================================================================
diff -u -r0e748d1af8c6854f89b9183270a533f9398088fb -rdafe0a1608f7b26bb40d8110b45af38a60ab6321
Binary files differ
Index: local/cantest.sh
===================================================================
diff -u
--- local/cantest.sh	(revision 0)
+++ local/cantest.sh	(revision dafe0a1608f7b26bb40d8110b45af38a60ab6321)
@@ -0,0 +1,5 @@
+cansend can0 001#A5A4D70300148900
+cansend can0 001#0000030000001C0B
+cansend can0 001#ABBF030000006911
+cansend can0 001#2A41E30000000000
+
Index: local/layout.sh
===================================================================
diff -u
--- local/layout.sh	(revision 0)
+++ local/layout.sh	(revision dafe0a1608f7b26bb40d8110b45af38a60ab6321)
@@ -0,0 +1,7 @@
+#!/bin/bash
+wmctrl -r "denali@DEN-UI" -e 0,2605,1265,1230,860
+wmctrl -r "GitKraken" -e 0,0,0,3779,2103
+wmctrl -r "Qt Creator" -e 0,1230,0,1365,2103
+wmctrl -r "Firmware Simulator" -e 0,2605,0,1200,1200
+wmctrl -r "simulator [~/Projects/simulator]" -e 0,0,0,1160,2103
+
Index: local/run.dialintest.sh
===================================================================
diff -u
--- local/run.dialintest.sh	(revision 0)
+++ local/run.dialintest.sh	(revision dafe0a1608f7b26bb40d8110b45af38a60ab6321)
@@ -0,0 +1,11 @@
+#!/bin/bash
+
+#git clone ssh://git@192.168.10.132:7999/vv/dialin.git workspace_UI/dialin
+cp -r Projects/dialin workspace_UI/dialin
+cd workspace_UI/dialin/tools/
+./setup_environment.sh
+./run_unit_tests.sh
+
+# cd ../tests/unit_tests/
+#python3 test_imports.py
+