dd-firmware / firmware / App / Monitors

Switches.c~

Clone Tools

Stats

Commits this week: 1
Total Committers: 1
Last Commit: 15:43
Commits this week: 1

Lines of code count not available

Commit Activity

Commits By Day In Week
52 week commits volume
Commits By Day In Week
Commits by day
Commits By Day In Week
Commits by hour
Commits By Hour In Day
Commit calendar
 

Most active committers (90 days)

loading
loading
  • last updated a few seconds ago
All Commits Reviews
Constraints
Constraints: committers
 
Constraints: files
Constraints: dates
Today
1 hr ago

Sean Nash

On DD f/w side, this should just be a simple pump controller. States should be Off and On (control to commanded Qsub). There is no flow sensor for feedback control, so assuming this is open loop si...

On DD f/w side, this should just be a simple pump controller. States should be Off and On (control to commanded Qsub). There is no flow sensor for feedback control, so assuming this is open loop similar to UF pump.
GenDialysate mode will have an HDF sub-state that signals this controller from Off to On and would also call separate controller for heater and separate (Switches) monitor for door sensors.

With all of that in mind, I think this unit should have a simpler name like SubPump.

1 hr ago

Sean Nash

I think there should be some state monitoring for potential alarm(s) in here too. Similar to BP door on TD f/w side where the current mode/state can signal this unit that it expects specific switch...

I think there should be some state monitoring for potential alarm(s) in here too. Similar to BP door on TD f/w side where the current mode/state can signal this unit that it expects specific switch state(s) (e.g. while in HDF state, we would expect the cap to be open and stowed and we would want to alarm if that was not the case).

1 hr ago

Sean Nash

Remove extra blank line.

Remove extra blank line.

1 hr ago

Sean Nash

Where is call to HDF controller?

Where is call to HDF controller?

1 hr ago

Sean Nash

Monitors should come before mode mgmt above.

Monitors should come before mode mgmt above.

1 hr ago

Sean Nash

What about HemoDiaFiltration.h?

What about HemoDiaFiltration.h?

1 hr ago

Sean Nash

What about initHDF?

What about initHDF?

1 hr ago

Sean Nash

Where is HemoDiaFiltration.h?

Where is HemoDiaFiltration.h?

1 hr ago

Sean Nash

Why does this file name have pound signs pre/post?

Why does this file name have pound signs pre/post?

1 hr ago

Sean Nash

This macro is already defined in Common.h.

This macro is already defined in Common.h.

1 hr ago

Sean Nash

Align all "=" or none of them.

Align all "=" or none of them.

1 hr ago

Sean Nash

DD HDF control data published should just be state and set rate. TD HDF data would have volume, etc...

DD HDF control data published should just be state and set rate. TD HDF data would have volume, etc...

1 hr ago

Sean Nash

This looks like pump control function. I think TD f/w should be doing this when setting Qsub before sending to DD f/w. Again, I think DD f/w should just be controlling pump to the Qsub rate given b...

This looks like pump control function. I think TD f/w should be doing this when setting Qsub before sending to DD f/w. Again, I think DD f/w should just be controlling pump to the Qsub rate given by TD f/w.
HDF volume should be calculated by TD f/w by integrating commanded Qsub over time.

1 hr ago

Sean Nash

Remove blank line.

Remove blank line.

1 hr ago

Sean Nash

Refactor so that only one return statement at end of function. This is in our coding standards.

Refactor so that only one return statement at end of function. This is in our coding standards.

1 hr ago

Sean Nash

I think TD should be handling all of these rules before setting Qsub and sending to DD.

I think TD should be handling all of these rules before setting Qsub and sending to DD.

2 hrs ago

Sean Nash

Generally, DD shouldn't need TMP. TD is calculating TMP. TD is using TMP to calculate Qsub. DD is just getting Qsub from TD and controlling the pump to that rate.

Generally, DD shouldn't need TMP. TD is calculating TMP. TD is using TMP to calculate Qsub. DD is just getting Qsub from TD and controlling the pump to that rate.

2 hrs ago

Sean Nash

Indent declarations.

Indent declarations.

2 hrs ago

Sean Nash

How can we help you with this?

How can we help you with this?

2 hrs ago

Sean Nash

Doesn't match file name. Why do we have a redundant file name with ~ suffix for your new units? If these are backup files from your editor, please do not add these to the git repo (delete them befo...

Doesn't match file name. Why do we have a redundant file name with ~ suffix for your new units? If these are backup files from your editor, please do not add these to the git repo (delete them before commit).

2 hrs ago

Sean Nash

DD is not calculating the rate I think. TD is sending target HDF rate to DD. So "calculated" should be "requested" or "commanded".

DD is not calculating the rate I think. TD is sending target HDF rate to DD. So "calculated" should be "requested" or "commanded".

2 hrs ago

Sean Nash

Add space before )

Add space before )

2 hrs ago

Sean Nash

Add blank line before return statement.

Add blank line before return statement.

2 hrs ago

Sean Nash

Align doxygen comments to right.

Align doxygen comments to right.

2 hrs ago

Sean Nash

Add blank line before banner

Add blank line before banner

5 hrs ago

Dara Navaei

LEAHI-DD-FIRMWARE-LDT-4002_HDF - FW Implementation - 3/4:
LEAHI-DD-FIRMWARE-LDT-4002_HDF - FW Implementation - 3/4: