firmware

Clone Tools
  • last updated a few seconds ago
Constraints
Constraints: committers
 
Constraints: files
Constraints: dates
DENBUG-307 updated the active cool mode to set the actuators prior to transitioning to complete state

    • -1
    • +2
    ./App/Modes/ModeHeatDisinfectActiveCool.c
DEN-17263 addressed the code review comments

    • -22
    • +7
    ./App/Controllers/ConcentratePumps.c
DENBUG-307 updated the active cool to run the concentrate pumps for a few seconds at the end of the mode

    • -23
    • +50
    ./App/Modes/ModeHeatDisinfectActiveCool.c
DENBUG-307 changed the heat disinfect active cool to run the concentrate pumps during the final reservoir drains

    • -12
    • +19
    ./App/Modes/ModeHeatDisinfectActiveCool.c
DENBUG-314 added more comment

DEN-17263 fixed the code to check the direction of the concentrate pumps and then decide based on that whether the measured speed values being negative or positive is correct or not

DEN-17263 added code to check the concentrate pumps speed direction

    • -0
    • +11
    ./App/Controllers/ConcentratePumps.c
DENBUG-307 added code to broadcast the concentrate pumps speed the way they are regardless of the direction of the pump

DENBUG-307 made the concentrate pumps speed check all absolute to be able to check both positive and negative targets and measured speeds

DEN-17263 change the concentrate pumps speed check to not use fabs for the measured values. The target speed is checked in fabs to cover the negative target speeds

DENBUG-309 added mode flush to the 5% tolerance of the concentrate pumps speed check

DENBUG-304 uncommeted the code that synchronizes the DG RTC time with HD upon starting a treatment

DENBUG-309 changed the concnetrate pumps speed monitor to 5% in heat disinfect

DENBUG-307 updated the heat disinfect to run the concentration pumps for the duration of heat disinfect from the time that the reservoirs are filled up until the end of disinfect R2 to R1

Bamboo Commit: Updated DGCommon.h with build versions from Bamboo

Bamboo Commit: Updated the Copyright section and replaced tabs with 4 spaces

DEN-17234 addressed the code review comments

DEN-17234 added pretreatment expedite test configuration to DG and implemented in DG fill

Bamboo Commit: Updated DGCommon.h with build versions from Bamboo

Bamboo Commit: Updated DGCommon.h with build versions from Bamboo

Bamboo Commit: Updated DGCommon.h with build versions from Bamboo

Bamboo Commit: Updated the Copyright section and replaced tabs with 4 spaces

    • -1
    • +1
    ./App/Controllers/ConductivitySensors.c
    • -1
    • +1
    ./App/Controllers/ConductivitySensors.h
  1. … 86 more files in changeset.
DENBUG-289 added more comments

DENBUG-284 updated the code

    • -1
    • +0
    ./App/Modes/ModeHeatDisinfectActiveCool.c
DEN-17135: added code to check the concentrate pumps calibration reocrd live. DEN-17146: fixed the active cool mode

    • -1
    • +2
    ./App/Modes/ModeHeatDisinfectActiveCool.c
DEN-17135 updated the concentrate pumps calibration

DEN-17135 added the calibration record to the acid and bicarb concentrate pumps

    • -4
    • +11
    ./App/Controllers/ConcentratePumps.c
Bamboo Commit: Updated DGCommon.h with build versions from Bamboo

Bamboo Commit: Updated the Copyright section and replaced tabs with 4 spaces

DENBUG-276, DENBUG-277 changed the location of the command the resets the chemicals used volume form mode fill to standby to reset the bottles upon transitioning to mode gen idle