dgfirmware

Clone Tools
  • last updated a few seconds ago
Constraints
Constraints: committers
 
Constraints: files
Constraints: dates
DEN-13460 updated the code with the DVT changes

    • -2
    • +2
    /firmware/App/Controllers/FlowSensors.c
    • -2
    • +2
    /firmware/App/Controllers/FlowSensors.h
    • -9
    • +25
    /firmware/App/Controllers/Heaters.c
Does the monitorPumpSpeed function generate the alarm

Does the monitorPumpSpeed function generate the alarm

Merge remote-tracking branch 'origin/staging' into DEN-12974-miscellaneous-flush-issues_bb

DEN-13460: fixed merge conflicts.

DEN-13460: Handle request to re-send active alarms.

DEN-13460 Implemented FAULT LED and Audio control in AlarmMgmt.c.

Bamboo Commit: Updated DGCommon.h with build versions from Bamboo

Bamboo Commit: Updated DGCommon.h with build versions from Bamboo

Merge branch 'DEN-13427-sw_dev-sprint-75_mg' into develop

DEN-13427: Errors and warnings fixes

Complication Fix

DEN-13427: DG Service Mode deenergizes and can Fault

Service Mode deenergizes actuators when we enter the mode. Fault is raised in Service Mode if we get a submode out of range.

DEN-13427: Message handler and response for DG's request to service mode

DEN-13460 CPLD low level driver for Fault LED, Fault Audio, Clean LED.

DEN-13460: If HD commands stop fill, clear bad fill flag in gen idle mode so we don't get stuck there.

Merge branch 'DEN-13460-dg_hd_dev-hd_dg_dvt-update-part-2' of ssh://dvm-linux02:7999/dg/dgfirmware into DEN-13460-dg_hd_dev-hd_dg_dvt-update-part-2

DEN-13460: Reset bad fill state in gen idle mode when detecting bad fill in case 2 bad fills back to back edge case.

DEN-12974 DEN-13556 Correct logic per SRSDG 333.

    • -2
    • +2
    /firmware/App/Modes/ModeHeatDisinfect.c
DEN12974 DEN-13558 Do not reset stateTimer in FlushR2AndDrainR1. Same issue will be in ModeChemicalDisinfect.

    • -35
    • +41
    /firmware/App/Modes/ModeChemicalDisinfect.c
    • -6
    • +6
    /firmware/App/Modes/ModeHeatDisinfect.c
DEN-12974 DEN-13560 Do not reset stateTimer in FlushR1AndR2.

    • -33
    • +39
    /firmware/App/Modes/ModeHeatDisinfect.c
Bamboo Commit: Updated DGCommon.h with build versions from Bamboo

Merge branch 'DEN-13460-dg_hd_dev-hd_dg_dvt-update-part-2' into develop

    • -49
    • +58
    /firmware/App/Controllers/Heaters.c
DEN-13460 updated the heaters with the latest primary heater gain check

    • -49
    • +58
    /firmware/App/Controllers/Heaters.c
Updated the baro pressure sensor to 14.7 psi

Bamboo Commit: Updated DGCommon.h with build versions from Bamboo

Merge branch 'DEN-13460-dg_hd_dev-hd_dg_dvt-update-part-2' into develop

DEN-13460 updated the latest DVT changes and the primary heater gain calculations

Should 0.5 be a #define?

Should 0.5 be a #define?

TODO should be all CAPS.

TODO should be all CAPS.

Is it really true that all function below this line are DVT?

Is it really true that all function below this line are DVT?

If these comment outs are not permanent, add a TODO. Otherwise remove the commented out code.

If these comment outs are not permanent, add a TODO. Otherwise remove the commented out code.