Pressures.c

Clone Tools
  • last updated a few seconds ago
Constraints
Constraints: committers
 
Constraints: files
Constraints: dates
DEN-14497 updated the drain pump flow control algorithm. Fixed the inlet water pressure, temperature, conductivity alarm recovery in treatment modes. Updated chemical disinfect flush mode

  1. … 10 more files in changeset.
DEN-13946 Use typedefs for itterating over sensors.

  1. … 3 more files in changeset.
DEN-13946 - Correct monitor functions where multiple sensors are "or'd" into a single alarm.

  1. … 2 more files in changeset.
DEN-14497 updated the drain pump control for the flow and updating chemical disinfect is in progress

  1. … 5 more files in changeset.
Bamboo Commit: Updated the Copyright section and replaced tabs with 4 spaces

  1. … 98 more files in changeset.
Bamboo Commit: Updated the Copyright section and replaced tabs with 4 spaces

  1. … 26 more files in changeset.
Merged staging

  1. … 16 more files in changeset.
DEN-14307 fixed the concentrate pumps' park command ID and addressed the code review comments. Updated heat disinfect mix drain states with the proper actuators

  1. … 12 more files in changeset.
DEN-14307 updated the cleaning modes per the SRS changes

  1. … 10 more files in changeset.
Merged DEN-14253

  1. … 10 more files in changeset.
Bamboo Commit: Updated the Copyright section and replaced tabs with 4 spaces

DEN-14356 addressed the code review comment

DEN-14536 updated the minimum acceptable inlet pressure

DEN-14307 updated the code and updated the checkAlarms.sh to check the alarms manual table upon compilation

  1. … 5 more files in changeset.
Bamboo Commit: Updated the Copyright section and replaced tabs with 4 spaces

  1. … 22 more files in changeset.
DEN-14175 addressed the code review comments and replaced the V3 enable software configuration flag with the hardware configuration flag from FGPA. Updated the trimmer heater's ramp state to check the use previous duty cycle flag instead of estimating the duty cycle.

  1. … 16 more files in changeset.
DEN-14175, DEN-13999 uncommented DG pressure sensors alarm

DEN-14175, DEN-13999 updated the pressure sensors persitent alarm. Added hardware configuration functions to check the status of the device (i.e. BETA, DVT)

  1. … 5 more files in changeset.
Bamboo Commit: Updated the Copyright section and replaced tabs with 4 spaces

  1. … 11 more files in changeset.
Merged staging

Bamboo Commit: Updated the Copyright section and replaced tabs with 4 spaces

  1. … 1 more file in changeset.
DEN-14166 added DVT FPGA thermistors, addressed the code review comment and added load cells sign extension

  1. … 8 more files in changeset.
Merged DEN-14166

  1. … 14 more files in changeset.
Merge branch 'staging' into DEN-13903-s80-mg-dg-comm-buffer-opti

Bamboo Commit: Updated the Copyright section and replaced tabs with 4 spaces

  1. … 39 more files in changeset.
Merged DEN-13834

  1. … 3 more files in changeset.
DEN-13834 added the drain pump current and direction alarms. Updated the heaters driver disinfect control. Added a check to ignore the trimmer heater stop command from HD if DG is in the heat disinfect or chemical disinfect

  1. … 6 more files in changeset.
DEN-13834 added more self test alarms. Added FPGA functions to get the drain pump current feedbakc, speed feedback, and direction

  1. … 5 more files in changeset.
updated pressure offset to reflect new calculations.

Merge branch 'DEN-13903-s80-mg-dg-comm-buffer-opti' into develop