Reservoirs.c

Clone Tools
  • last updated a few seconds ago
Constraints
Constraints: committers
 
Constraints: files
Constraints: dates
DEN-15274 addressed the code review comments

  1. … 3 more files in changeset.
DEN-15274, DEN-15351 fixed the trimmer heater issue

DEN-15274 fixed the bad fill target volume

  1. … 1 more file in changeset.
DEN-15274 updated the heaters control code

  1. … 1 more file in changeset.
DEN-15274 addressed the code review comments

  1. … 3 more files in changeset.
DEN-15274, DEN-15246 Added code to not lose the commanded fill volume from HD due to multiple bad fill modes. Updated the heaters code to keep getting the dialysate the flow for the trimmer control. Updated the drain to volume function

  1. … 5 more files in changeset.
DEN-15274 created another function to drain to a target volume in milliliters

  1. … 7 more files in changeset.
DEN-15274 work in progress, added a set of commands to be able to get, send, and set the load cells tare values

  1. … 6 more files in changeset.
Bamboo Commit: Updated the Copyright section and replaced tabs with 4 spaces

  1. … 13 more files in changeset.
DEN-15166 added the Maxon drain pump RPM and the new non-isolated voltage

  1. … 9 more files in changeset.
Bamboo Commit: Updated the Copyright section and replaced tabs with 4 spaces

  1. … 17 more files in changeset.
DEN-14999, DEN-15031 added code to receive and support different types of acid and bicarb in the treatment

  1. … 5 more files in changeset.
DEN-14999 merged the remote changes and updated the fill mode with the acid conductivity values

  1. … 1 more file in changeset.
Merge branch 'DEN-14689-messaging-bugs' into develop

  1. … 6 more files in changeset.
Merge branch 'staging' into DEN-14763-dg_hd_dev-hd_dg_dvt-update-part-10

  1. … 6 more files in changeset.
Bamboo Commit: Updated the Copyright section and replaced tabs with 4 spaces

  1. … 7 more files in changeset.
DEN-14834 updated the code to just send the heater command in Idle and Drain if the primary heater is not on. Addressed the code review comments

  1. … 4 more files in changeset.
DEN-14834 updated that get target primary heater function to accomodate the changes from pre-treatment. Removed the range check from the drain pump measured RPM

  1. … 4 more files in changeset.
DEN-14763, DIAL-233, DEN-14812 added a command to be able to set the dialysate mixing ratios and added an event to send the average conductivity of acid and bicarb at the end of the fill. Changed the measured flow function to flow with concentrate pumps in drain pump's control to flow function

  1. … 7 more files in changeset.
Bamboo Commit: Updated the Copyright section and replaced tabs with 4 spaces

DEN-14495 changed the PRd drain threshold

Bamboo Commit: Updated the Copyright section and replaced tabs with 4 spaces

  1. … 22 more files in changeset.
DEN-14559 updated the cleaning modes with the SRS changes

  1. … 7 more files in changeset.
Bamboo Commit: Updated the Copyright section and replaced tabs with 4 spaces

  1. … 98 more files in changeset.
Bamboo Commit: Updated the Copyright section and replaced tabs with 4 spaces

  1. … 26 more files in changeset.
DEN-14307 fixed the concentrate pumps' park command ID and addressed the code review comments. Updated heat disinfect mix drain states with the proper actuators

  1. … 12 more files in changeset.
DEN-14307 added a command to be able to start and stop heat disinfect active cool mode. Added a monitor function to check the status of the caps during the heat disinfect active cool mode. Updated heating code to use TD2 temperature sensor to set the primary heater's target for the later DVT devices

  1. … 10 more files in changeset.
DEN-14307 updated the usage info records in the NV data management

  1. … 5 more files in changeset.
Bamboo Commit: Updated the Copyright section and replaced tabs with 4 spaces

  1. … 22 more files in changeset.
DEN-14175 addressed the code review comments and replaced the V3 enable software configuration flag with the hardware configuration flag from FGPA. Updated the trimmer heater's ramp state to check the use previous duty cycle flag instead of estimating the duty cycle.

  1. … 16 more files in changeset.