Services

Clone Tools
  • last updated a few seconds ago
Constraints
Constraints: committers
 
Constraints: files
Constraints: dates
DEN-14197: updated Dialin msg handling DIAL-200: Implemented handler for total fill volume override. Implemented fill mode broadcast override handler. DIAL-212: Implemented RO feedback voltage override handler.

  1. … 2 more files in changeset.
DEN-14175 updated the extra temperature to 0.0 from 2.0

DEN-14197: implemented RO pump profile switching. Implemented Flow to PWM function RO pump with profiles as a parameter. Created a SW fault for PI profiles out of range.

  1. … 2 more files in changeset.
DEN-14197: Initial attempt at PI controller profiles with usage in ro pump

  1. … 1 more file in changeset.
Merge branch 'DEN-14175-dg_hd_dev-hd_dg_dvt-update-part-5' into develop

  1. … 3 more files in changeset.
RESOLVED IN CODE WALKTHROUGH

RESOLVED IN CODE WALKTHROUGH

RESOLVED IN CODE WALKTHROUGH

RESOLVED IN CODE WALKTHROUGH

RESOLVED IN CODE WALKTHROUGH

RESOLVED IN CODE WALKTHROUGH

DEN-14175 addressed the code review comments and replaced the V3 enable software configuration flag with the hardware configuration flag from FGPA. Updated the trimmer heater's ramp state to check the use previous duty cycle flag instead of estimating the duty cycle.

  1. … 14 more files in changeset.
This is done to get an average of the fill temperature as well as the last fill temperature prior to tranistioning to Gen Idle. These values are used for the next estimation and are different from ...

This is done to get an average of the fill temperature as well as the last fill temperature prior to tranistioning to Gen Idle. These values are used for the next estimation and are different from the heaters driver.

Done.

Done.

No, it should be removed.

No, it should be removed.

Merged DEN-14175

  1. … 1 more file in changeset.
Where is valveSensedStates being updated?

Where is valveSensedStates being updated?

Remove comment.

Remove comment.

DEN-14175, DEN-13999 updated the pressure sensors persitent alarm. Added hardware configuration functions to check the status of the device (i.e. BETA, DVT)

  1. … 4 more files in changeset.
Not clear this needs to be done. I believe is properly handled in heaters when you get a temperature value and configured for V3.

Not clear this needs to be done. I believe is properly handled in heaters when you get a temperature value and configured for V3.

DEN-14175, DIAL-213 added drain pump current and direction override commands, updated the heaters driver with the latest optimization requirements, added a DG valves sensed states override command

  1. … 6 more files in changeset.
DG-DEN-14175_DG HD Dev HD DG Dvt Update Part 5
DG-DEN-14175_DG HD Dev HD DG Dvt Update Part 5
Merge branch 'DEN-14101-sw-s82-mg-DIAL-179-DIAL-184' into develop

  1. … 3 more files in changeset.
DEN-14101: DIAL-184: Fixed gen idle/bad fill publish override handler to actually work.

  1. … 1 more file in changeset.
DEN-14101: DIAL-184: Fixed return type for drain pump current handler

DEN-14101: DEN-179: comm handling for Dial-179

  1. … 1 more file in changeset.
DG-DEN-14166_DG HD Dev HD DG Dvt Update Part 4
DG-DEN-14166_DG HD Dev HD DG Dvt Update Part 4
Bamboo Commit: Updated the Copyright section and replaced tabs with 4 spaces

  1. … 7 more files in changeset.
Bamboo Commit: Updated the Copyright section and replaced tabs with 4 spaces

  1. … 1 more file in changeset.