firmware

Clone Tools
  • last updated a few minutes ago
Constraints
Constraints: committers
 
Constraints: files
Constraints: dates
Bamboo Commit: Updated DGCommon.h with build versions from Bamboo

Bamboo Commit: Updated the Copyright section and replaced tabs with 4 spaces

    • -1
    • +1
    ./App/Controllers/TemperatureSensors.c
    • -2
    • +2
    ./App/Controllers/TemperatureSensors.h
DENBUG-327 updated the VectorCAST test cases

DENBUG-327 updated the baro sensor mfg CRC check

    • -5
    • +7
    ./App/Controllers/TemperatureSensors.c
DENBUG-327 added code to make the baro sensor MFG CRC as LSB

DENBUG-327 updated the baro sensor code

    • -16
    • +28
    ./App/Controllers/TemperatureSensors.c
    • -0
    • +1
    ./App/Controllers/TemperatureSensors.h
Bamboo Commit: Updated DGCommon.h with build versions from Bamboo

Bamboo Commit: Updated DGCommon.h with build versions from Bamboo

Bamboo Commit: Updated the Copyright section and replaced tabs with 4 spaces

    • -1
    • +1
    ./App/Controllers/ConductivitySensors.c
    • -2
    • +2
    ./App/Controllers/ConductivitySensors.h
DENBUG-318 addressed the code review comment

DENBUG-318 addressed the code review comments

DENBUG-318 added code to request the DG institutional values in mode standby until they are received

DENBUG-318 added code to keep requesting DG institutional values once start DG has been sent until the values are received

DENBUG-318 changed the min inlet water conductivity to recovery offset to 10 uS/cm. Updated the vectorcast test cases

    • -1
    • +1
    ./App/Controllers/ConductivitySensors.c
DENBUG-318 added the request command to get the DG institutional record from HD upon starting the DG

DENBUG-318 added an RO rejection ratio event

DENBUG-318 changed the max RO rejection ratio to min RO rejection ratio in percent and updated the mode fill calculations to check the RR

DENBUG-320 removed the acid and bicarb used volumes in mode fill broadcast

DENBUG-318 removed the inlet recovery conductivity alarm #define

    • -1
    • +0
    ./App/Controllers/ConductivitySensors.c
DENBUG-318 changed the inlet water conductivity low alarm recovery

    • -1
    • +2
    ./App/Controllers/ConductivitySensors.c
DENBUG-318 added a new event for min inlet water conductivity alarm from HD institutional record

    • -0
    • +1
    ./App/Controllers/ConductivitySensors.c
DENBUG-318 updated the code to receive all the DG institutional record items. Added code to use the min inlet water conductivity alarm from the institutional record

    • -8
    • +23
    ./App/Controllers/ConductivitySensors.c
    • -0
    • +1
    ./App/Controllers/ConductivitySensors.h
    • -11
    • +12
    ./App/Services/SystemCommMessages.c
DENBUG-319 added code to receive a command from dialing to enable the mode fill chemicals test

    • -0
    • +23
    ./App/Services/SystemCommMessages.c
DENBUG-322 added code to set CPi and CPo to 20 uS/cm if the values are less than 20 uS/cm

    • -1
    • +13
    ./App/Controllers/ConductivitySensors.c
DENBUG-319 added code to skip the acid and bicarb check in mode fill if it is not the first fill

DENBUG-318 changed the location of requesting RO rejection ratio upon starting DG

DENBUG-320 addressed a code review comment

DENBUG-320 brought back the start fill command after removing alarms 281, 282

DENBUG-318 added the word max to the RO rejection ratio

DENBUG-320 added the word max to the RO rejection ratio