LEAHI-DD-FIRMWARE-LDT-4002

Bamboo Commit: Updated the Copyright section and replaced tabs with 4 spaces

    • -20
    • +14
    /sources/model/hd/alarm/MAlarmMapping.cpp
Bamboo Commit: Updated MAlarmMapping.cpp

    • -14
    • +20
    /sources/model/hd/alarm/MAlarmMapping.cpp
Bamboo Commit: Updated the Copyright section and replaced tabs with 4 spaces

    • -20
    • +14
    /sources/model/hd/alarm/MAlarmMapping.cpp
Merged release/p1b/staging and resolved the conflicts

    • -2
    • +2
    /sources/model/hd/alarm/MAlarmMapping.cpp
Bamboo Commit: Updated MAlarmMapping.cpp

    • -14
    • +20
    /sources/model/hd/alarm/MAlarmMapping.cpp
Bamboo Commit: Updated the Copyright section and replaced tabs with 4 spaces

    • -1
    • +1
    /sources/canbus/MessageInterpreter.cpp
    • -20
    • +14
    /sources/model/hd/alarm/MAlarmMapping.cpp
Merged release/DENBUG-335-air-trap-fill-design-improvement-P1B-Staging

DENBUG-335: Air Trap Fill Design Improvements: Updated the institutional record to receive and display the end treatment blood flow rate in mL/min

    • -1
    • +1
    /sources/canbus/MessageInterpreter.cpp
    • -2
    • +2
    /sources/model/hd/alarm/MAlarmMapping.cpp
Bamboo Commit: Updated MAlarmMapping.cpp

    • -14
    • +20
    /sources/model/hd/alarm/MAlarmMapping.cpp
Bamboo Commit: Updated the Copyright section and replaced tabs with 4 spaces

    • -20
    • +14
    /sources/model/hd/alarm/MAlarmMapping.cpp
Bamboo Commit: Updated MAlarmMapping.cpp

    • -15
    • +21
    /sources/model/hd/alarm/MAlarmMapping.cpp
Bamboo Commit: Updated the Copyright section and replaced tabs with 4 spaces

    • -1
    • +1
    /sources/canbus/MessageInterpreter.cpp
    • -20
    • +14
    /sources/model/hd/alarm/MAlarmMapping.cpp
Merged DENBUG-335

Merge branch 'staging' into DENBUG-335-air-trap-fill-design-improvement

Bamboo Commit: Updated MAlarmMapping.cpp

    • -14
    • +20
    /sources/model/hd/alarm/MAlarmMapping.cpp
Bamboo Commit: Updated MAlarmMapping.cpp

    • -14
    • +20
    /sources/model/hd/alarm/MAlarmMapping.cpp
Bamboo Commit: Updated the Copyright section and replaced tabs with 4 spaces

    • -20
    • +14
    /sources/model/hd/alarm/MAlarmMapping.cpp
Bamboo Commit: Updated MAlarmMapping.cpp

    • -14
    • +20
    /sources/model/hd/alarm/MAlarmMapping.cpp
Bamboo Commit: Updated the Copyright section and replaced tabs with 4 spaces

    • -20
    • +14
    /sources/model/hd/alarm/MAlarmMapping.cpp
On DD f/w side, this should just be a simple pump controller. States should be Off and On (control to commanded Qsub). There is no flow sensor for feedback control, so assuming this is open loop si...

On DD f/w side, this should just be a simple pump controller. States should be Off and On (control to commanded Qsub). There is no flow sensor for feedback control, so assuming this is open loop similar to UF pump.
GenDialysate mode will have an HDF sub-state that signals this controller from Off to On and would also call separate controller for heater and separate (Switches) monitor for door sensors.

With all of that in mind, I think this unit should have a simpler name like SubPump.

I think there should be some state monitoring for potential alarm(s) in here too. Similar to BP door on TD f/w side where the current mode/state can signal this unit that it expects specific switch...

I think there should be some state monitoring for potential alarm(s) in here too. Similar to BP door on TD f/w side where the current mode/state can signal this unit that it expects specific switch state(s) (e.g. while in HDF state, we would expect the cap to be open and stowed and we would want to alarm if that was not the case).

Remove extra blank line.

Remove extra blank line.

Where is call to HDF controller?

Where is call to HDF controller?

Monitors should come before mode mgmt above.

Monitors should come before mode mgmt above.

What about HemoDiaFiltration.h?

What about HemoDiaFiltration.h?

What about initHDF?

What about initHDF?

Where is HemoDiaFiltration.h?

Where is HemoDiaFiltration.h?

Why does this file name have pound signs pre/post?

Why does this file name have pound signs pre/post?

This macro is already defined in Common.h.

This macro is already defined in Common.h.

Align all "=" or none of them.

Align all "=" or none of them.