ModeFill.c

Clone Tools
  • last updated a few seconds ago
Constraints
Constraints: committers
 
Constraints: files
Constraints: dates
DEN-14607, DEN-13999 updated the fill mode the not command the VPo valve to fill state upon exiting the pause state. Updated the pressures driver to assume the overidden pressure is absolute and not add the baro pressure to make it absolute

  1. … 2 more files in changeset.
DEN-14561 Decrease concentrate lines prime from 95 to 60 sec.

Bamboo Commit: Updated the Copyright section and replaced tabs with 4 spaces

  1. … 23 more files in changeset.
Merge branch 'staging' into DEN-14497-dg_hd_dev-hd_dg_dvt-update-part-7

  1. … 23 more files in changeset.
Fixed merge conflicts.

  1. … 22 more files in changeset.
DEN-14497 updated the drain pump flow control algorithm. Fixed the inlet water pressure, temperature, conductivity alarm recovery in treatment modes. Updated chemical disinfect flush mode

  1. … 10 more files in changeset.
DEN-14497: Added CPo and RR alarms to fill mode recoverable list.

DEN-14497: Changed CPo and RR alarms to only occur at end of fill based on average conductivity.

  1. … 4 more files in changeset.
Bamboo Commit: Updated the Copyright section and replaced tabs with 4 spaces

  1. … 98 more files in changeset.
Bamboo Commit: Updated the Copyright section and replaced tabs with 4 spaces

  1. … 26 more files in changeset.
Merged staging

  1. … 16 more files in changeset.
DEN-14307 resolved the merge conflicts

  1. … 4 more files in changeset.
DEN-14307 fixed the concentrate pumps' park command ID and addressed the code review comments. Updated heat disinfect mix drain states with the proper actuators

  1. … 12 more files in changeset.
DEN-14307: Addressed code review comments.

  1. … 10 more files in changeset.
DEN-14307 added a command to be able to start and stop heat disinfect active cool mode. Added a monitor function to check the status of the caps during the heat disinfect active cool mode. Updated heating code to use TD2 temperature sensor to set the primary heater's target for the later DVT devices

  1. … 10 more files in changeset.
DEN-14307: Added support for parking concentrate pumps.

  1. … 13 more files in changeset.
Merge DEN-14327 branch.

  1. … 1 more file in changeset.
Bamboo Commit: Updated the Copyright section and replaced tabs with 4 spaces

  1. … 12 more files in changeset.
DEN-14197: Code review changes. Pre-merge fixes.

  1. … 3 more files in changeset.
Merge branch 'staging' into DEN-14197-sw-s83-mg-pi-optimizations

  1. … 5 more files in changeset.
DEN-14197: pre-staging merge. code review comments.

  1. … 2 more files in changeset.
DEN-14197: Addressed code review comments.

  1. … 4 more files in changeset.
DEN-14307 work in progress updated heat disinfect

  1. … 4 more files in changeset.
Fixed merge conflicts.

  1. … 8 more files in changeset.
Bamboo Commit: Updated the Copyright section and replaced tabs with 4 spaces

  1. … 1 more file in changeset.
DEN-14237 added the _RELEASE_ macro around a configuration check in ModeFill

Bamboo Commit: Updated the Copyright section and replaced tabs with 4 spaces

  1. … 22 more files in changeset.
DEN-14197: updated Dialin msg handling DIAL-200: Implemented handler for total fill volume override. Implemented fill mode broadcast override handler. DIAL-212: Implemented RO feedback voltage override handler.

  1. … 4 more files in changeset.
DEN-14175 addressed the code review comments and replaced the V3 enable software configuration flag with the hardware configuration flag from FGPA. Updated the trimmer heater's ramp state to check the use previous duty cycle flag instead of estimating the duty cycle.

  1. … 16 more files in changeset.
DEN-14175, DIAL-213 added drain pump current and direction override commands, updated the heaters driver with the latest optimization requirements, added a DG valves sensed states override command

  1. … 8 more files in changeset.