Activity leahi-dialin/

I would not do that because the function names and messages for each project should be different to avoid confusion. I think that is fine for now. RESOLVED.

I would not do that because the function names and messages for each project should be different to avoid confusion.
I think that is fine for now.

RESOLVED.

12:17 pm

Vendor - TEL - Santhoshkumar Reddy Alasandagutti

even though we are sending U08 at Firmware. Due to structure padding Raw message for priority is converted as 16 bits. While receiving we need to read them as U16. Here is my debug values [CortexR4...

even though we are sending U08 at Firmware. Due to structure padding Raw message for priority is converted as 16 bits. While receiving we need to read them as U16. Here is my debug values [CortexR4] ALARM_PROP_T size = 22 bytes
byte[0] = 0x03
byte[1] = 0x00
byte[2] = 0x6F
byte[3] = 0x00
byte[4] = 0x01
byte[5] = 0x00
byte[6] = 0x00
byte[7] = 0x01
byte[8] = 0x00
byte[9] = 0x00
byte[10] = 0x01
byte[11] = 0x00
byte[12] = 0x00
byte[13] = 0x01
byte[14] = 0x00
byte[15] = 0x00
byte[16] = 0x01
byte[17] = 0x00
byte[18] = 0x00
byte[19] = 0x01
byte[20] = 0x0A
byte[21] = 0x00

This is structure defined at firmware side
struct AlarmTableRequestPayload

Unknown macro: { U08 alarmPriority; U16 alarmSubRank; U08 alarmSource; U08 alarmIsFault; U08 alarmIsDDFault; U08 alarmStops; U08 alarmConditionClearImmed; ///< Alarm condition is cleared immediately (does not persist after alarm triggered) U08 alarmNoClear; ///< Alarm cannot be cleared (unrecoverable)? U08 alarmNoResume; ///< Alarm prevents treatment resume U08 alarmNoRinseback; ///< Alarm prevents rinseback U08 alarmNoEndTreatment; ///< Alarm prevents ending treatment U08 alarmBlockRinseback; ///< Alarm should not trigger while in rinseback states U08 alarmBlockEndTx; ///< Alarm should not trigger while in post-treatment mode U08 alarmNoBloodRecirc; ///< Alarm prevents blood re-circulation U08 alarmNoDialysateRecirc; ///< Alarm prevents dialysate re-circulation U08 alarmAutoResume; ///< Alarm should resume automatically once the condition is cleared U08 alarmClearOnly; ///< Clear only this alarm on user acknowledgment U08 alarmTreatmentLog; ///< Log alarm to treatment log if active during treatment U16 alarmID; ///< Alarm ID }

;
typedef struct AlarmTableRequestPayload ALARM_PROP_T;

12:11 pm

Behrouz NematiPour

So the same channels are used for both the Leahi and Denali? I am not talking about how collisions are handled; that is handled by the CAN driver, not the FW or SW. My point is that the CAN Channel...

So the same channels are used for both the Leahi and Denali?
I am not talking about how collisions are handled; that is handled by the CAN driver, not the FW or SW.
My point is that the CAN Channels by themselves do not have the meaning we want; they are only a priority.
As we defined them, we gave them a meaning as a category; therefore, it is better to name them the Denali/Leahi Channels rather than the CAN Channels.

12:06 pm

Behrouz NematiPour

RESOLVED.

12:06 pm

Behrouz NematiPour

def fp_versions(self, major: int, minor: int, micro: int, build: int, fpga_id: int, fpga_major: int, fpga_minor: int, fpga_lab: int, compatibility_rev: int...

def fp_versions(self, major: int, minor: int, micro: int, build: int,
                     fpga_id: int, fpga_major: int, fpga_minor: int, fpga_lab: int,
                     compatibility_rev: int):
     """
     Broadcasts the current dd Version Data (Msg ID: 0x0F, 15)
     Args:
         @param major: (uint) - Major version number
         @param minor: (uint) - Minor version number
         @param micro: (uint) - Micro version number
         @param build: (uint) - Build version number
         @param fpga_id: (int) - FPGA id version number
         @param fpga_major: (int) - FPGA Major version number
         @param fpga_minor: (int) - FPGA Minor version number
         @param fpga_lab: (int) - FPGA Lab version number
         @param compatibility_rev: (uint) - The FWs/UI compatibility revision
     @return: None
     """
     if not self.can_enabled:
         raise ValueError("CAN Interface is not enabled")

     payload =  conversions.unsigned_byte_to_bytearray   (major            )
     payload += conversions.unsigned_byte_to_bytearray   (minor            )
     payload += conversions.unsigned_byte_to_bytearray   (micro            )
     payload += conversions.unsigned_short_to_bytearray  (build            )
     payload += conversions.unsigned_byte_to_bytearray   (fpga_id          )
     payload += conversions.unsigned_byte_to_bytearray   (fpga_major       )
     payload += conversions.unsigned_byte_to_bytearray   (fpga_minor       )
     payload += conversions.unsigned_byte_to_bytearray   (fpga_lab         )
     payload += conversions.unsigned_integer_to_bytearray(compatibility_rev)

     message = CAN.CanMessage.build_message(
                                         channel_id=CAN.CanChannels.fp_sync_broadcast_ch_id,
                                         message_id=msg_ids.MsgIds.MSG_ID_FP_VERSION_RESPONSE.value,
                                         payload=payload)

     self.can_interface.send(message, 0)