dd-firmware

Clone Tools

Stats

Commits this week: 24
Total Committers: 17
Last Commit: 28 May
Commits this week: 24

Lines of code count not available

Commit Activity

Commits By Day In Week
52 week commits volume
Commits By Day In Week
Commits by day
Commits By Day In Week
Commits by hour
Commits By Hour In Day
Commit calendar
 

Most active committers (90 days)

loading
loading
  • last updated a few seconds ago
All Commits Reviews
Constraints
Constraints: committers
 
Constraints: files
Constraints: dates
Today
20 mins ago

Vendor - TEL - Jashwant Gantyada

21 mins ago

Vendor - TEL - Jashwant Gantyada

I think we also need this to be uncommented, as we were running into an alarm because of this.

I think we also need this to be uncommented, as we were running into an alarm because of this.

44 mins ago

Vinayakam Mani

Added new field for d1 filtered temperature and restored the pressure sensor temperature.

Added new field for d1 filtered temperature and restored the pressure sensor temperature.

46 mins ago

Vinayakam Mani

The latest code from staging has an update and fixes this comment. It's not showing here, since the file was already reviewed.

The latest code from staging has an update and fixes this comment. It's not showing here, since the file was already reviewed.

46 mins ago

Vinayakam Mani

as discussed, these were outcome of the test results. we will review these gains with latest controller.

as discussed, these were outcome of the test results. we will review these gains with latest controller.

47 mins ago

Vinayakam Mani

Done.

Done.

47 mins ago

Vinayakam Mani

Done.

Done.

Thursday 28 May
1:47 pm

Dara Navaei

LEAHI-DD-FIRMWARE-LDT-3975_Water Treatment and Degassing - FW Iteration - 4/4:
LEAHI-DD-FIRMWARE-LDT-3975_Water Treatment and Degassing - FW Iteration - 4/4:
1:38 pm

Sean Nash

LDT-3975: Added distinct s/w fault IDs for PID controller faults.

Options
    • -0
    • +5
    /firmware/App/Services/AlarmMgmtSWFaults.h
Wednesday 27 May
4:28 pm

Sean Nash

Fix comment.

Fix comment.

4:24 pm

Dara Navaei

3:43 pm

Dara Navaei

Bamboo Commit: Updated DDCommon.h with build versions from Bamboo.

Options
    • -1
    • +1
    /firmware/App/DDCommon.h
3:43 pm

Dara Navaei

Bamboo Commit: Updated the Copyright section and replaced tabs with 4 spaces

Options
    • -0
    • +16
    /firmware/App/Modes/ModeUpdate.c
    • -0
    • +16
    /firmware/App/Modes/ModeUpdate.h
    • -2
    • +2
    /firmware/App/Modes/OperationModes.c
    • -2
    • +2
    /firmware/App/Services/AlarmMgmtSWFaults.h
    • -2
    • +2
    /firmware/App/Services/Messaging.c
    • -2
    • +2
    /firmware/App/Services/Messaging.h
    • -2
    • +2
    /firmware/App/Services/SystemCommDD.c
    • -2
    • +2
    /firmware/App/Services/SystemCommDD.h
3:39 pm

Dara Navaei

Merged LDT-3272

Options
3:38 pm

Vendor - TEL - Jashwant Gantyada and Sean Nash

2:46 pm

Sean Nash

On DD f/w side, this should just be a simple pump controller. States should be Off and On (control to commanded Qsub). There is no flow sensor for feedback control, so assuming this is open loop si...

On DD f/w side, this should just be a simple pump controller. States should be Off and On (control to commanded Qsub). There is no flow sensor for feedback control, so assuming this is open loop similar to UF pump.
GenDialysate mode will have an HDF sub-state that signals this controller from Off to On and would also call separate controller for heater and separate (Switches) monitor for door sensors.

With all of that in mind, I think this unit should have a simpler name like SubPump.

2:39 pm

Sean Nash

I think there should be some state monitoring for potential alarm(s) in here too. Similar to BP door on TD f/w side where the current mode/state can signal this unit that it expects specific switch...

I think there should be some state monitoring for potential alarm(s) in here too. Similar to BP door on TD f/w side where the current mode/state can signal this unit that it expects specific switch state(s) (e.g. while in HDF state, we would expect the cap to be open and stowed and we would want to alarm if that was not the case).

2:36 pm

Sean Nash

Remove extra blank line.

Remove extra blank line.

2:33 pm

Dara Navaei

LDT-3272 addressed the code review comments

Options
    • -1
    • +1
    /firmware/App/Services/Messaging.c
    • -16
    • +0
    /firmware/App/Services/SystemCommDD.h
    • -16
    • +16
    /firmware/DD.dil
    • -10
    • +10
    /firmware/source/can.c
2:31 pm

Sean Nash

Where is call to HDF controller?

Where is call to HDF controller?

2:31 pm

Sean Nash

Monitors should come before mode mgmt above.

Monitors should come before mode mgmt above.

2:30 pm

Sean Nash

What about HemoDiaFiltration.h?

What about HemoDiaFiltration.h?

2:29 pm

Sean Nash

What about initHDF?

What about initHDF?

2:28 pm

Sean Nash

Where is HemoDiaFiltration.h?

Where is HemoDiaFiltration.h?

2:24 pm

Sean Nash

Why does this file name have pound signs pre/post?

Why does this file name have pound signs pre/post?

2:14 pm

Sean Nash

This macro is already defined in Common.h.

This macro is already defined in Common.h.

2:14 pm

Sean Nash

Align all "=" or none of them.

Align all "=" or none of them.

2:13 pm

Sean Nash

DD HDF control data published should just be state and set rate. TD HDF data would have volume, etc...

DD HDF control data published should just be state and set rate. TD HDF data would have volume, etc...

2:11 pm

Sean Nash

This looks like pump control function. I think TD f/w should be doing this when setting Qsub before sending to DD f/w. Again, I think DD f/w should just be controlling pump to the Qsub rate given b...

This looks like pump control function. I think TD f/w should be doing this when setting Qsub before sending to DD f/w. Again, I think DD f/w should just be controlling pump to the Qsub rate given by TD f/w.
HDF volume should be calculated by TD f/w by integrating commanded Qsub over time.

2:08 pm

Sean Nash

Remove blank line.

Remove blank line.