leahi-common

Clone Tools
  • last updated a few seconds ago
Constraints
Constraints: committers
 
Constraints: files
Constraints: dates
Based on the Denali properties, I have written the following.

Based on the Denali properties, I have written the following.

replace with else block

replace with else block

convert to switch case

convert to switch case

set treatment modality.

set treatment modality.

Priority doesn't look right. Should be High I think. Check properties from Denali project.

Priority doesn't look right. Should be High I think. Check properties from Denali project.

LEAHI-TD-FIRMWARE-LDT-3539_Air Infusion - TD
LEAHI-TD-FIRMWARE-LDT-3539_Air Infusion - TD
Vinay, based on your work with rinsepump, Do you have any persistence value in mind?

Vinay, based on your work with rinsepump, Do you have any persistence value in mind?

Can we check some persistence before declaring alarm?

Can we check some persistence before declaring alarm?

recommend running the pump at few sample speeds and observe the measured feedback and fix the tolerance number.

recommend running the pump at few sample speeds and observe the measured feedback and fix the tolerance number.

Rinse pump fault? do we have one? remove concentrate references, commented codes, empty lines.

Rinse pump fault? do we have one? remove concentrate references, commented codes, empty lines.

No, Yes for lowering event. Fill event uses PWM 150 always irrespective of Qb and Venous pressure only lower event used equation based PWM and that is in the range of 60-250 , not default., based ...

No, Yes for lowering event.

Fill event uses PWM 150 always irrespective of Qb and Venous pressure
only lower event used equation based PWM and that is in the range of 60-250 , not default., based on venous pressure it changes

Looks like we are doing a lot of the dialysate temp control in Gen Dialysate mode. Do we not do any heating in PreGen mode? Even if all dialysate heating is done in this mode, should we consider cr...

Looks like we are doing a lot of the dialysate temp control in Gen Dialysate mode. Do we not do any heating in PreGen mode?
Even if all dialysate heating is done in this mode, should we consider creating a service controller (like BC controller) to manage this complex temperature control?

Resolve merge conflicts.

Resolve merge conflicts.

Do we ever want to use the default (250)? Do we always want to use this venous pressure based power level?

Do we ever want to use the default (250)? Do we always want to use this venous pressure based power level?

Why not for release?

Why not for release?

Remove extra blank line.

Remove extra blank line.

Remove extra blank line.

Remove extra blank line.

Remove extra blank line.

Remove extra blank line.

LEAHI-TD-FIRMWARE-LDT-1903_Air Trap Level Control - TD - 04: DEV - Feature Implementation
LEAHI-TD-FIRMWARE-LDT-1903_Air Trap Level Control - TD - 04: DEV - Feature Implementation
For B1.0/B1.9 - Where Diener silencer 2000 pumps, this macro needs to be enabled.

For B1.0/B1.9 - Where Diener silencer 2000 pumps, this macro needs to be enabled.

There are recent changes done on FPGA register in staging for B1.0/B1.9. please merge the latest changes here.

There are recent changes done on FPGA register in staging for B1.0/B1.9. please merge the latest changes here.

Add valve details per HDD (may be 2.0 valves. as we remove beta 1/1.9 in sometime)

Add valve details per HDD (may be 2.0 valves. as we remove beta 1/1.9 in sometime)

add new valves.

add new valves.

Can we follow the same terminology as DD, starting a variable with 'fpga...'. for all IOFP variables?

Can we follow the same terminology as DD, starting a variable with 'fpga...'. for all IOFP variables?

typo - used.

typo - used.

Add as HDF hallsensor. start the comment with capital letter R.

Add as HDF hallsensor. start the comment with capital letter R.