dd-firmware

Clone Tools
  • last updated a few seconds ago
Constraints
Constraints: committers
 
Constraints: files
Constraints: dates
Merge branch staging into LDT-4409-dialysate-composition-beta-2.1-WCID-implementation

LDT-4409 enable dry bicart default

    • -17
    • +12
    /firmware/App/Controllers/MixingControl.h
    • -5
    • +5
    /firmware/App/Modes/ModeGenDialysate.c
    • -1
    • +2
    /firmware/App/Modes/ModePreGenDialysate.c
LDT-4409 dry bicart implementation plus refactoring closed loop control

    • -14
    • +25
    /firmware/App/Controllers/DryBiCart.c
    • -0
    • +1136
    /firmware/App/Controllers/MixingControl.c
    • -0
    • +96
    /firmware/App/Controllers/MixingControl.h
Bamboo Commit: Updated DDCommon.h with build versions from Bamboo.

Merge branch 'LDT-4485-dd-conductivity-sensors-d17' into develop

LDT-4485: fixed pumpid call

LDT-4485: updates to sub pump rpm measure alarm to not monitor during off state.

Merge branch 'staging' into LDT-4485-dd-conductivity-sensors-d17

    • -25
    • +20
    /firmware/App/Monitors/Conductivity.c
Is this normal UF volume or normal UF volume + Iso UF Volume?

Is this normal UF volume or normal UF volume + Iso UF Volume?

Consider moving this validity check into the setTDRequestedGenDState function. And what should we do if it's not valid?

Consider moving this validity check into the setTDRequestedGenDState function.
And what should we do if it's not valid?

Why only these states are valid?

Why only these states are valid?

Remove list of states from comment. It is not a complete list and we shouldn't even try to list them here anyway.

Remove list of states from comment. It is not a complete list and we shouldn't even try to list them here anyway.

LDT-4409 addressed review comments

    • -859
    • +103
    /firmware/App/Controllers/DryBiCart.c
    • -40
    • +0
    /firmware/App/Controllers/DryBiCart.h
LDT-3962 merge latest from staging

in initial fill we are not closing D64, only in supply cycle, just before supply start, we close it and when supply end, we open it again. we need to maintain the pressure balance in chamber F

in initial fill we are not closing D64, only in supply cycle, just before supply start, we close it and when supply end, we open it again.
we need to maintain the pressure balance in chamber F

will address it in new file created for mixing

will address it in new file created for mixing

LDT-3735: Updated validation for service and system records

    • -21
    • +26
    /firmware/App/Services/NVRecordsDD.c
LDT-3735: Added default values for institutional settings

    • -20
    • +35
    /firmware/App/Services/NVRecordsDD.c
LDT-3735: Moved the file NVDriver, NVJobQ and NVMgmt to FwCommon

    • -180
    • +0
    /firmware/App/Drivers/NVDriver.c
    • -764
    • +0
    /firmware/App/Services/NVMessaging.c
  1. … 10 more files in changeset.
Bamboo Commit: Updated DDCommon.h with build versions from Bamboo.

Bamboo Commit: Updated the Copyright section and replaced tabs with 4 spaces

Merge branch 'LDT-4001-hdf-fw-implementation-2-4' into staging

LDT-3975: updates to iofp refinements LDT-1197: updates to power budget constriants and calculation. LDT-3102: updates to flush duration

WIP on LDT-3975-Boost-Pump

    • -31
    • +76
    /firmware/App/Drivers/FluidPump.c
LDT-4001: code review comments

LDT-4001: code review comments

fixed thanks

fixed thanks

Should we change msg ID from speed to rate?

Should we change msg ID from speed to rate?